Search found 891 matches
- November 9, 2017, 7:16 am
- Forum: Truck Talk
- Topic: Tail gate won't open
- Replies: 2
- Views: 766
Re: Tail gate won't open
When you take the latch handle off, you have access to the rods that release the tailgate. Use vise grips on the rods and make sure they move away from the side they lock. if they both move, then you are binding somewhere else.
- November 8, 2017, 7:37 am
- Forum: Truck Talk
- Topic: carb - boiling gas - diagnosis
- Replies: 7
- Views: 1482
Re: carb - boiling gas - diagnosis
I'd take the top of the carb off and see what might be in the float bowl. If you have sediment or rust, you still have an issue with the fuel system. Its pretty easy to replace the fuel lines. I'd also check the filler neck. If it is rusty inside, the sacale can get into your system. Also check the ...
- November 8, 2017, 7:30 am
- Forum: Truck Talk
- Topic: Engine possibilities for a 64
- Replies: 4
- Views: 941
Re: Engine possibilities for a 64
One great feature of our slicks is that the engine compartment is big enough to fit almost any engine you could consider. I do not know about the coyote engine having the same mount points as the earlier small blocks. This engine is so much larger due to the overhead cams, that most conversions comp...
- November 7, 2017, 12:24 pm
- Forum: Truck Talk
- Topic: Headlight switch stuck
- Replies: 14
- Views: 1688
Re: Headlight switch stuck
You've got a tricky problem, normally the answer would be take it out - but you cant take it out without pulling out the knob and shaft. The switch was available from NAPA as of a few years ago and is definitely available from suppliers as is the know and shaft. I'd disconnect the battery, and spray...
- November 6, 2017, 7:44 am
- Forum: Hints and Tricks
- Topic: Disc brake conversion 1977 f150 on 1966 f100
- Replies: 0
- Views: 3484
Disc brake conversion 1977 f150 on 1966 f100
This is just and FYI. This was the third time I've done this conversion. The firs two times, I just used everything from the 150 bolting the radius arms and ibeams in place of the 66 version. I also used all the f150 steering linkage. This time I was not able to use the f150 radius arms because on t...
- October 31, 2017, 7:19 am
- Forum: Truck Talk
- Topic: N Series Video
- Replies: 2
- Views: 683
Re: N Series Video
I like the N series. Like to try and make one into a pickup like some of the new f550s i've seen.
- October 31, 2017, 7:15 am
- Forum: Projects & Builds
- Topic: Ryanjay11's 65 F100 build
- Replies: 58
- Views: 25192
Re: Ryanjay11's 65 F100 build
You did a great job in a short time frame. Sounds like it is a riot to drive. There will be good dry days that you'll be able to stretch its legs through the winter, it'll just give you time to take care of those little things.
- October 30, 2017, 6:27 am
- Forum: Truck Talk
- Topic: Stock style master cylinder
- Replies: 12
- Views: 1642
Re: Stock style master cylinder
Was it rebuilt? I always go new on brake parts.
- October 27, 2017, 6:26 am
- Forum: Projects & Builds
- Topic: '62 F100 Uni - yes another Crown Vic swap
- Replies: 157
- Views: 74447
Re: '62 F100 Uni - yes another Crown Vic swap
Loved the video. Looks like a ton of fun and once again great work!
- October 23, 2017, 6:20 am
- Forum: Projects & Builds
- Topic: Ryanjay11's 65 F100 build
- Replies: 58
- Views: 25192
Re: Ryanjay11's 65 F100 build
Looks great, what are you going to do with all the extra time once the little things are ironed out?
- October 20, 2017, 7:30 am
- Forum: Projects & Builds
- Topic: '62 F100 Uni - yes another Crown Vic swap
- Replies: 157
- Views: 74447
Re: '62 F100 Uni - yes another Crown Vic swap
I want to know what piratical purposes you are up to. ![Wink :wink:](./images/smilies/icon_wink.gif)
![Wink :wink:](./images/smilies/icon_wink.gif)
- October 18, 2017, 6:12 am
- Forum: Off Subject
- Topic: Overhaulin
- Replies: 17
- Views: 4103
Re: Overhaulin
I like the show, though I wish they would show more of the 'how-to'. Personally I enjoy the work and tend to be bored with a vehicle once it is done. The cars/trucks I've kept the longest are the ones I haven't done much to other than keep them running. I have no use for a vehicle that is too nice t...
- October 17, 2017, 6:43 am
- Forum: Truck Talk
- Topic: 66 trans ?
- Replies: 2
- Views: 771
Re: 66 trans ?
I didn't think it would matter as it is just going through a cooler.
- October 17, 2017, 6:42 am
- Forum: Truck Talk
- Topic: Carb Troubles Autolite 1100
- Replies: 7
- Views: 1645
Re: Carb Troubles Autolite 1100
I wonder if your float is too high. That could provide excess gas at all time, but also allow the idle mixture screw to have no real effect.
- October 16, 2017, 1:50 pm
- Forum: Projects & Builds
- Topic: my shipwrecked '63
- Replies: 1020
- Views: 288294
Re: my shipwrecked '63
Glad you seem to be easing slowing back to task. I think you'd fined stainless tubing a royal PIA. Stainless is harder, thus harder to form and more brittle. Then you have issues with sealing for the same reason. I put stainless fuel lines on a car once and I'll never use it again. Looks good but mo...
- October 6, 2017, 6:12 am
- Forum: Truck Talk
- Topic: Styleside Box floors
- Replies: 13
- Views: 1637
Re: Styleside Box floors
Since they can do multiple lengths, I suspect they are rolling these (like a gutter machine) and not stamping them. That's why the profile is consistent front to back through the piece. Still a lot of work to have created the machine to run these out. Gotta appreciate someone filling the gap.
- October 6, 2017, 6:08 am
- Forum: Truck Talk
- Topic: Pictures
- Replies: 3
- Views: 849
Re: Pictures
There was a post earlier. If you use firefox or chrome, you can use an extension to get the pics to display. We were not the only site hit by this. So much great information compromised! After I installed the extension, I can now see all the old photobucket pics. Here's the link I used: https://chro...
- October 5, 2017, 6:18 am
- Forum: Truck Talk
- Topic: Styleside Box floors
- Replies: 13
- Views: 1637
Re: Styleside Box floors
Didn't we already have an option in the 73-79 8' floors that have been available for a while. They are complete and come with cross braces. These do not have the correct stamping on the front and back edges (neither do the 73-79 as the frame width changed). They are certainly better than what so man...
- October 4, 2017, 6:12 am
- Forum: Truck Talk
- Topic: source of door leak
- Replies: 4
- Views: 1186
Re: source of door leak
Those leaks sure look like they are coming from inside the panels, which would indicate a leak at the rain gutter.
- October 4, 2017, 6:10 am
- Forum: Projects & Builds
- Topic: Ryanjay11's 65 F100 build
- Replies: 58
- Views: 25192
Re: Ryanjay11's 65 F100 build
I have been watching your posts. Great work. Keep the post coming.