Rooster did this on his tan and brown slick, he live s up in jersey where I used to live. His was hidden in the inside of bed but in the wheel well if I remember correctly. His frame was 70’s f100 I think.. are you saying the fuel door is on the inside of the bed? I am needing a set up that has a f...

https://ibb.co/w7zKmg9 https://ibb.co/DwMJBmN https://ibb.co/rpTCBqV https://ibb.co/BqnxFQZ https://ibb.co/ZhTBf71 https://ibb.co/Db4cByL https://ibb.co/vD09TX6 My dad ran this set up for about 14 years hauling some heavy scrap loads. The set up can be cleaned up and done cleaner but its a bolt in. ...

Hey guys. I picked up some 95 f150 bucket seats for my 64. Turns out I gotta ditch the in cab tank, which I wanted to do anyway. Problem is I have zero interest in using the bed floor for a filler door location. I want to fill it up through the outer bedside like a modern truck. What tanks and necks...

Center wire should be orange and it comes from the dash through the instrument voltage regulator same as oil gauge/idiot light, and temp gauge. The ground wire goes from the tab on the edge of the sending unit to a good ground, not on the tank, usually screwed to the brace under the rear window. Th...

unibody madness wrote:are you running a separate ground to the sending unit when out of the tank.? could it be a bad connection when you place it in the tank?

we thought we had moved both wires in just about every position possible trying to rule that out..

are you running a separate ground to the sending unit when out of the tank.? could it be a bad connection when you place it in the tank? yes, and back story is that we replace the DC repop that was never right..junk...and it got to where sometimes it worked some times it didn't but started as only ...

Hey guys, I have a issue with my gas sending unit...it only works outside the tank..but once it's inside it don't work at all even full and the float is good. The wires seem to be fine..only thing I can think of us that the voltage regulator..and the other gauges seek to act fine like they always ha...

Hey guys. I pulled a nice deluxe heater from a 63 f800 firetruck. It needs new seals but the vent door handle is intact and thats why I bought it. So I haven't seem a seal kit so I am assuming Ill have to make my own? And I've found a nos acordion seal for the vent to cowl area on flea bay so its do...

Hey guys. I pulled a nice deluxe heater from a 63 f800 firetruck. It needs new seals but the vent door handle is intact and thats why I bought it. So I haven't seem a seal kit so I am assuming Ill have to make my own? And I've found a nos acordion seal for the vent to cowl area on flea bay so its do...

Hey, Ive been watching the gauge for a while, Ive bent the arm a time or two thinking it was hitting something but now I know its way off when it reads bone dry and I put 12 gallons or so in and it fills it to the brim..is the float defective? Dousnt sound like it has gas in it...drives me nuts kniw...

Hello, I have a nice np435 sitting around and my t98 is a great transmission, even speed shifts pretty nice for what it is but Im at the lowest teeth count gear they made and Im still slow on the speedometer so I was wondering how many gear options the np435 has. And I am aware the bolt pattern is s...

This guy keeps all his old stuff,all the imports get crushed.......going back in the morning for a set of nice fenders and a couple of 16",8hole lock ring wheels for Farmmotorsports..... I live 45 minutes from Springfield, mo where is this exactly? My 64 needs a drivers fender, door panel trim...

http://www.slick60s.com/gallery/image.php?mode=thumbnail&album_id=879&image_id=12698 This is what I used. It is a booster/MC from a 65-66 mustang, all I had to do was redrill two holes in mounting brackets to match firewall and pedal bracket holes. and I used a 3/8" thick piece of alum...

Hello, I got to looking at my bed, while I had the bolts out and..the wood blocks are still intact but the front of the bed seems to be so low its rubbing the back of the cab at the top. My cab has been off and isnt right because I aligned it to make the bed not look so bad at the time. But the fram...

shipwrecked wrote:I used the stock interiors as well.

looks like the verdict is stock interiors. Thanks guys

Getting close to being able to put carpet in my 64, and Im wondering who sells the most durable, high-quality carpet out there, along with mass backing that may help with wind noise? (Already have jute with heat block) Wishful thinking?
As always thanks in advanced.

Hey guys, I'm needing a decent drivers front fender as mine is pretty mutilated from a side swipe. How much is one worth? Anyone have one near or in the south west missouri area? Thanks in advanced.

Ok, is there any strategy for keeping the gas inside my gas tank and not pouring down the side of the truck from the cap? I try not to fill it too full, but it's hard to be accurate. Just filled up yesterday and gas is literally pouring out when I made a right hand turn today. There must be a bette...

I was using a small dia 69 Torino booster, but it had an adapter plate that I made, and then made an adjustable rod to the pedal. Sorry no pictures, took it off and gave it to a buddy for his truck. I like the manual disc feel better than the touchy power stuff. Robert thanks! Ill have to look for ...

mac wrote:So would spacers solve it? I want to keep my bottle caps.

you might look into aftermarket steelies, I've seen some used with 66 and later caps so I'm sure it coud be done they added the clips by riviting them. I may do the same to my 64 as a set of winter wheels