Slick 60's

well shes starting to go back together.. planning on getting everything back on the front end and bolted together so when i get ready to paint i can just unbolt fenders from cab and unbolt radiator bolts and paint separate... but this way i can get it back together and running.. it actually went together pretty easy, i had to space the inner fender on the passenger side out about a half an inch to geth it right.. i would have gotten a little more done but when i moved my bed to get to the front piece of the truck i found a freaking huge red wasp nest prolly a foot wide.. i hosed em down with wasp spray.. i swear there was a 1000 of them suckers.. lol there was dead wasps all over my shop.. anyway heres my pics

new bump stops, i went with beltech bump stops.. alot cheaper than original, got all 4 cheaper than 1 original.. lol

therealjoeshmoe wrote:new bump stops, i went with beltech bump stops.. alot cheaper than original, got all 4 cheaper than 1 original.. lol

nice work on your truck but i think that brake hose may be upside down
not 100% on that but to me it does not look right, i believe the hose should come out on the bottom of the bracket to avoid that severe u bend

NOPE THEY ARE ON RIGHT. THAT'S HOW THEY WERE BEFORE, MY AXLE IS JUST SAGGING WAY DOWN. THERE ISN'T A SEVERE BEND IN THE HOSE WHEN THE AXLE IS BACK IN PLACE.. I LOOKED ON THE INTERNET AND FOUND A LOT OF OTHER OLD FORDS ARE THE SAME WAY.. I MAY BE WRONG BUT I DON'T THINK SO.. LOL

guess so
just looked weird

very long time since i messed with 2wd front brake hose

Joe...you're doing it right! I just read through your entire build thread...all I can say is "Great Job!" Mine is done for awhile, so I'll be watching here.
Steve-

SteveCanup wrote:Joe...you're doing it right! I just read through your entire build thread...all I can say is "Great Job!" Mine is done for awhile, so I'll be watching here.
Steve-

thanks.. i know mine is not on the level of some but im happy with how its turning out.. I think ive got a guy lined up to get the truck ready to paint.. i hope i havent forgot how to drive it.. lol

Any updates?????????

Yep...still watching....anticipating...

well, i decided to lower the truck again.. lol i got drop beams and flip kit for it . stay tuned im fixing to start back up shortly lol

Glad to hear that you're still "on it" ...staying tuned....

well more parts gathered.. got a rhinopac new clutch kit, vacation is next week... and its on! as soon as i mow the yard lol

Get that yard mowed.....so we can see the truck stuff....

ok well slickstock got my itch started again! lol anyway got out in the shop this weekend and got to work on ole red a little while. i didnt get everything i wanted done but i did get the whole front end tore back off and got the twin I beams off and ready to install the new drop beams.. I got my bad hub replaced and put new bearings in, and painted my tie rod relocaters.. im gonna ryno line the new i beams tonight and hopefully get them installed this week.. this will be the absolutly last freaking time i take ole red apart!!! its going together for good! stay tuned! lol

What we are looking at sure looks good. Now just keep the pictures coming so we can see the rest of it in the coming weeks.

Hey...you're back! Keep it going! and the Pics too.....

Its always fun to see someone get the FEVER BAD after hitting the last Slickstock.. hopefully it lasts awhile !!

well what do you do when the finish on your aim drop beams does not satisfy you? well you sand them down and prime them so you can ryno line them of course! lol i will be ryno lining them tonight

here they are sprayed with deezee bedliner spray..

ready to bolt under the truck now..

finally got me a new harness for old red.. its a 24 circuit

now i can get the dash painted and put back together!!!