Where to find rubber ash tray rubber bumpers?

BarnieTrk · Post by **BarnieTrk** » February 23, 2010, 1:15 pm

Fellas,

I'm looking for the two, small rubber bumpers that are missing from the dash holes at the top corners of the ash tray opening on my '65 F250.
Not a big deal, but the cigar ash tray shakes & rattles too much!

They are black, round and about 1/4" in diameter.
I didn't see them listed in my DC catalog nor my NPD catalog.

Anyone know where I can locate some of these little bumpers?

If I can't locate some OE-style bumpers, I'll have to cut up some rubber and simply glue them in place....but I'd rather not do that if I can locate some OEM-style bumpers.
Even some used bumpers would be fine, but those that I've looked at in junkers were so hard & dried out that they'd break off trying to remove them.

Thanks in Advance for any & all help, Guys!

BarnieTrk

kenwright396 · Post by **kenwright396** » February 23, 2010, 1:22 pm

Dennis Carpenter has them for $5.00 but there's a minimum $10 shipping order, Ken

http://www.parts123.com/parts123/yb.dll?parta~partsort

BarnieTrk · Post by **BarnieTrk** » February 23, 2010, 1:51 pm

kenwright396 wrote:Dennis Carpenter has them for $5.00 but there's a minimum $10 shipping order, Ken

http://www.parts123.com/parts123/yb.dll?parta~partsort

Ken,
Thanks for the reply!

I couldn't make your link work for me, but I looked (again) through my catalog (the one with the red '66 on the cover) and I finally found them.
They were listed under, "Miscellaneous items, page 91, part# 359422-S. Cool.....

As far as the minimum order deal - I can handle that as I'll likely also get a complete rubber bumper set for around my hood (I'm missing some now) and probably also get the replacement bumpers for at the tailgate-to-box too.
THANKS AGAIN!

BarnieTrk

GDG · Post by **GDG** » February 23, 2010, 3:39 pm

I got mine at the junk yard, while scrounging I picked an assortment from glove boxes, ash trays, fuel tank doors. etc. Now I usually have one that will work when the need arises.
They are also very cheap!!
Doug

bird55 · Post by **bird55** » February 23, 2010, 6:37 pm

I found similar replacements at my local hardware store in those"Dorman" pull-out boxes, Also for the glove box door. Quicker, cheaper.

jwh f-100 · Post by **jwh f-100** » February 23, 2010, 8:24 pm

Dude!!!, Your ash tray is rubber??????

Post by **Greg D** » February 23, 2010, 8:29 pm

jwh f-100 wrote:Dude!!!, Your ash tray is rubber??????

That's that mid year introduction that doesn't rattle over railroad tracks.

BarnieTrk · Post by **BarnieTrk** » February 24, 2010, 9:16 am

Thanks for all the replies and ideas, Fellas!!

Doug,
As I mentioned earlier, my attempts to remove them from junkyard Slicks haven't been good because they would not come out without tearing them up.
I guess I should have been looking in newer trucks for some that might have been the same size.

Bird55,
DOH!

That is a good idea... why didn't I think of that? I will try to match up a set from my local parts store.

Jason,
Easy, Dude...... your head may hurt in the AM, but you'll be fine!

Greg,
LOL!!

Thanks again, everyone!
BarnieTrk

Johnny Canuck · Post by **Johnny Canuck** » February 24, 2010, 10:26 am

I got mine at LMC. Got the ones for the glovebox too. Saved paying shipping charges by riding there in Mike Kimbrell's uni while Slickstock 3 was on

I had no success pulling them out of old trucks either. they would just crumble.

ICEMAN6166 · Post by **ICEMAN6166** » February 24, 2010, 9:19 pm

Johnny Canuck wrote:I got mine at LMC. Got the ones for the glovebox too. Saved paying shipping charges by riding there in Mike Kimbrell's uni while Slickstock 3 was on

I had no success pulling them out of old trucks either. they would just crumble.

as much as i try to save and recycle the ashtray bumpers are about impossible to get out intact. i have much better luck with the glovebox ones but at the price they are best ordered new.

hey thats my right arm sticking out of Caseys truck in the pic