all you guys got updated pics, here's mine (Dialup WARNING)

The place to talk Slicks. All we ask is that discussion has something to do with slicks...

Moderators: Casey 65, Kid

blackagatha
Posts: 2582
Joined: March 10, 2007, 12:49 am
Location: Arizona

all you guys got updated pics, here's mine (Dialup WARNING)

Post by blackagatha »

Granted I have no recent news, but all of the pics I had of Black Agatha until today were several years out of date, and I decided that I oughta go take some fresh ones... Lots of the pics were the subject of recent posts that I didnt have anything decent to illustrate with...

SO I went out and took lots of pics. Of everything. Some subtle nuances, some things that may be of interest, others of lesser interest! haha


SO, lets begin, shall we???



relatively recent, not today- the light was really bad and a little dirty
Image

the battery clamp I just made
Image
Image

73 econoline MC, wilwood prop. valve
Image

Skip's swaybar conversion (Bronco 2) I think I will flip it around someday?
Image

the headlight relays
Image

rear fender braces I made from wagon axles
Image

rear roll pan, didnt have somebody to light up the brake lights in the bed rolls. You can see the oily spots from what drafts up from the drippy engine. And I hate those tail lights. I want to french something into the roll pan...
Image

erm, main leaky- the intake didnt seal right and it drips down on the pipe
Image

my home made door panels
Image

door pins and relay (needs a bolt) for dome light
Image

auxiliary fuse boxes- put in when I removed a wad of wiring and inline fuses I put in years ago
Image

the strange brake light switch I've mentioned recently
Image

and this one shows the spring I put on the pedal to pull it off of the MC... it is about 1/8 inch from pressing on the brakes. I did this to make adjusting the light switch easier. The light was either staying on all the time or had to push too much brake before it came on. So I made it to where it will come on with just touching the pedal but not actually on the brakes.
Image

hidden backup light switch
Image

and indicator so I remember to shut it off
Image

My repro Mirrors
Image

and the one that points off toward casey65's...
Image

the seatbelts- the backing plate goes all the way into the door and window frames.
Image

you can see the mechanisms here
Image

the backing for seatbelt mech
Image

and the center backer. there is a chunk of a leaf spring that the bolts go thru.
Image

the Rocket Box and assorted crap
Image

the glove box box
Image

Image

extinguisher bolted down
Image

note the terrible hole from PO that I need to weld up nice
Image

and the grille I screwed down over the hatchet wound in the dash
Image

the shitty steering column (damn I wish I had the rest of the stuff to swap out the steering with my Flaming River brushed SS column)
Image

hiding antenna- not electric
Image

terrible coverage when I painted hood
Image

bad hinges
Image

bad coverage on roof... wtf!
Image

vent window rubber- 6 years old? already cracked all to hell
Image

i finally got some nice period correct wipers
Image

I hate this freaking gas tank
Image

definitely not a factory switch
Image

very not good. I need to modify the pan, and raise the drivetrain a few inches. the axle hits the pan and made a horrible crease
Image

the sway bar also hits
Image

I can raise drivetrain several inches without modifying floor
Image

and a few without changing brake cylinder.
Image

my current engine mount arms
Image

these damned power lines were inducing some voltage on aggie and was shocking me during oil change- yeah I know it wasnt Aggie's fault, doesnt shock any where else. the lines buzz loudly!
Image

So Sexy- except for them crappy tail lights!!!! grr!
Image
Image

you DONT want to meet her from this angle!!!!
Image
'63 with 390 & lots of juice. But never enough. Always want more.
ImageImageImage
User avatar
jwh f-100
Posts: 1903
Joined: June 11, 2007, 6:25 pm
Location: Equinunk, PA
United States of America

Post by jwh f-100 »

BA. Yeah pics are good. Aggie is a cool truck. Don't cut her up. The engine looks great. That front bumper has some attitude.
As far as your taillights. You could hit a trucking supply store. I bet some 4" grommet mount stop&tail with some 2" back up lights would look nice in your roll pan.

You had asked about my trans adapt/axle clearance in the other post. It is a 302 plus I have it raised a little higher than I'd prefrer so the z-bar would line up perfectly. Is that a FE truck pan?? Maybe there are some different pan options for you so you will not need to modify your drive train. The lower the better for handling.

EDIT: BA, This is an after thought but if nothing else, for now lower your suspension bumpers?????

What size steering wheel is that? How does she steer?
Last edited by jwh f-100 on June 6, 2008, 2:37 pm, edited 1 time in total.
Jason

Beer will change the world.

I don't know how but it will.
User avatar
lefty
Posts: 152
Joined: April 25, 2008, 1:08 pm
Location: Central Northeast Texas!!

Post by lefty »

Definately check out some different pans... You want to keep the roll center as low as possible so it wont dive in the corners as much. Raising the motor would need a stiffer sway bar and stiffer springs.
'61 Uni SWB BBW Custom Cab 302 T-5 w/ Power brakes
It ain't pretty either!
Image
BIGTRIP
Posts: 256
Joined: January 30, 2007, 6:49 pm
Location: looking at TX
Contact:

Post by BIGTRIP »

nice truck! I will have to examine those pics and research that type of brakelight switch. its funny you would mention raising your engine because I was just talking about lowering mine with shorter box tubing. I
will make a thread for opinions after I get some good pics.

I thought I had drivetrain problems until I saw where your axle is beating the hell out of your oil pan. ouch.
Being stroked is nice, but I would rather be blown!
User avatar
Slick Fan
Posts: 4085
Joined: November 4, 2006, 5:09 pm
Location: UTAH...snow blows!

Post by Slick Fan »

BIGTRIP wrote:I will have to examine those pics and research that type of brakelight switch.
That's a 50's Chebby style brake light switch; http://www.fredstruckparts.com/ListItems.aspx


Cool Aggie pics, Man! The primered areas on my truck used to do that rust-thru thing, too. Primer is porous & doesn't seal very well, so after a while, it will eventually start surface rusting. No biggie, just sand again & re-primer..should be good for a couple more years. :D

I agree, you should try something different for an oil pan. At frist, I was thinking you could use a 4x4 pan, but it looks like the rear crossmember you made will interfere with that. Maybe if you moved the crossmember forward, you could use the 4x4 pan.

I like your truck, it reminds me of mine a lot, from my younger days. :)
My "Slickitis" affliction began here...
Image


66 F100 CC/65 F100 CC/66 F250 CC
If it starts to rain, they'll tax the splash.
If you want to fish, they'll tax the bass.
If you plant a yard, they'll tax the grass.
If you don't play nice, they'll fine your *$#!
willy3486
Posts: 817
Joined: July 11, 2006, 10:31 am
Location: Smithville TN

Post by willy3486 »

As far as your backup goes heres what I did to mine. I got a small switch that only makes contact when you press it in and when you release it the switch no longer makes contact. I took a piece of metal and bent it to the shape I needed to mount it and to mount the switch also. I then mounted it to the cap so that when it is in reverese it makes contact. No problems when you forget it. Mine a 3 speed but looks like you could fabricate something for a floor or automatic as well. Or even get one off a newer truck at a junkyard and retrofit it.
User avatar
jakdad
Posts: 1968
Joined: July 18, 2006, 4:07 pm
Location: Katy,Texas

Post by jakdad »

Awesome truck!! Here are a set of tail lights that would look cool in or on your roll pan. Good luck,

http://cgi.ebay.com/ebaymotors/1940-For ... dZViewItem
Jim
truckerdaddy66
Posts: 114
Joined: January 22, 2007, 9:14 am
Location: new caney, tx.

Post by truckerdaddy66 »

Nice truck!
Cool looking roll pan,love those tiny rust holes in tail gate,mine has em too! Gives it character and I like little dings and dents in a truck. I'm a rat rodder at heart. Keep up the good work. and P.S. THE 390 IS JUST THE TICKET!

Truckerdaddy66 New Caney ,Tx.
blackagatha
Posts: 2582
Joined: March 10, 2007, 12:49 am
Location: Arizona

Post by blackagatha »

yeah as far as handling goes, I know raising the engine will hurt it. but my pan is getting a hell of a beating. It is a standard car pan I think, as far as that xmember is concerned, it wouldnt be a big deal to fab a new one. that was the easiest part of the whole project.

yeah, that is the main detriment to dealing with a straight axle... the whole thing moves... hit a 3 inch speedbump, the engine also hits the speedbump... or so it thinks so...

oh, and about the bump stops, the engine mounts I put in actually raise trouble for installing the bumpers. the studs sticking out of the bump stops arent long enough to got thru the mounts too. they werent low enough to do any good anyway though. I really should do something about them, but I cant figure out what...

I think I may wind up modifying a pan, perhaps. hard telling. Especially when I wind up dropping her, I'm definitely going to need to raise the engine a bit. And another indication that it sits too low is that the fan is swinging less than a 1/4 inch from the front xmember. not an ideal location, I want to make up a fan shroud, but with that tight clearance it may be an issue. I might end up putting an electric fan on her, which would be the best bet, but I think they're ugly- the one I got is all shiny metal and ford red... it looks cool.

as far as the rusty primer goes... I got terrible coverage to start with, my spray gun is a POS, it seems that it either wanted to spew it out like spackling or just enough for it to look black for a few days but was so miserable thin that it was crap. you can see on the roof especially, it is not just rust showing thru, but also some of the remaining factory red primer and stuff showing thru.

I need to get some real satin black paint on it.... I am tempted to rub it down and just rattle can it... the spraygun made such terrible results and cost so much that it would be basically the same.... The rear rollpan was sprayed in rustoleum Automotive black primer, is even enough color for my taste, smooth as a baby's ass, whereas most of the rest of the truck feels like a freakin pumice stone. I oughta spray the whole thing with the Rusto.
and the bed needs some attention too.... it's pretty rough. bad cracked bondo in the left fender, rust holes in stake pockets and tailgate.... and the whole thing needs to be torn down and rebuilt so it will quit it's infernal SQUEAKING!!!
'63 with 390 & lots of juice. But never enough. Always want more.
ImageImageImage
truckerdaddy66
Posts: 114
Joined: January 22, 2007, 9:14 am
Location: new caney, tx.

Post by truckerdaddy66 »

Hey Blackaggie , wet sand it with 400 paper ,get some brown paper from dollar general, buy good masking tape from the hardware store. Spring for some high dollar oil base rustoleum,a couple of quarts will do it, gallon of napha to thin the paint. Thin it to about 6 or 7 second dripping off stir stick method . Sand her in the morning, wash her good with soap and water.Let her dry good, tape her off and paint her . Over time she will fade in the hot desert sun( satin look). It will make a night & day difference ,you can can always spend the big bucks later!

Be sure to get some hardener from tractor supply ,or buy paint there too . Find a upright low presure paint gun gravity feed .I used kabota orange and its bright. I want to try to pin stripe it myself w/black paint like in the Old school rat rod mags.

Well enough of me, keep on trucking.

Truckerdaddy66,New Caney ,Tx.
jeffw

b

Post by jeffw »

hey aggie got right,, we should make this the everyone show your pics thread,, very very interesting!! thanks aggie,, got some ideas from your truck,, If everyone agrees, I'll post too!! aggie I see we like the same tunes??

[albumimg]4259[/albumimg]
BIGTRIP
Posts: 256
Joined: January 30, 2007, 6:49 pm
Location: looking at TX
Contact:

Post by BIGTRIP »

I'm not too shy about showing my truck. it is what it is, right?


hey B.A., I was thinking about you saying you wanted to french taillights in the roll pan. it used to be back in the day when mini trucks were all the rage they would take the long thin caddy tails and french them in either the stock location or the roll pan. I always thought it looked pretty cool but overdone at the time. these days you almost never see it so it may be something to think about.

caddy lights
http://www.stylintrucks.com/parts.aspx? ... od_ids=695
Being stroked is nice, but I would rather be blown!
blackagatha
Posts: 2582
Joined: March 10, 2007, 12:49 am
Location: Arizona

Post by blackagatha »

mhmm caddy lights... dunno. I was thinkin some pointy ovals I saw on ebay would look good....

haha the radio... it is alright, kinda sucks though. no mp3, blares if you turn it up past 25, cant hear it below 20 when drving, 23 on freeway
'63 with 390 & lots of juice. But never enough. Always want more.
ImageImageImage
User avatar
jakdad
Posts: 1968
Joined: July 18, 2006, 4:07 pm
Location: Katy,Texas

Post by jakdad »

Here's a guy that can fix you up. Taillight King make swap meets all over. I have bought lights from him at Texas swap meets. He has almost any OEM lights you can think of as well as after market. The Lincoln Cosomo lights would look killer on your truck, but very rare and $$$$$$$.

http://www.taillightking.com/hot_rod_li ... mblies.htm
Jim
rctcomp
Posts: 27
Joined: June 4, 2008, 9:42 pm
Location: Grantsville, Ut

Post by rctcomp »

B.A.
Great truck! It's hard to restore a daily driver. Drove a 65 Fairlane for years, definitely spent a lot more time just keeping the thing on the road that I did making it look good. Judging by the pics, your making a helluva lot more progress than I ever did.

Can you give me some more information on your seatbelt setup? How did you fab the top backing plate? Where did you get the mechanisms?

Thanks and looks good.
blackagatha
Posts: 2582
Joined: March 10, 2007, 12:49 am
Location: Arizona

Post by blackagatha »

rrg!
Last edited by blackagatha on June 19, 2008, 4:03 am, edited 1 time in total.
'63 with 390 & lots of juice. But never enough. Always want more.
ImageImageImage
blackagatha
Posts: 2582
Joined: March 10, 2007, 12:49 am
Location: Arizona

Post by blackagatha »

yeah, doing mods to my Daily Driver is hard... everything must be on a strict schedule, and if something doesnt get done on time I got trouble. If it is not done, hopefully I can at least put it back together in time to (go back to school).

I'm goin HOME (IE GARAGE) in a few days... oh man, I cant wait!

The biggest plan for the summer is to fabricate a rear sump oil pan that looks like the cantons... I'm not sure about the funny front pot though. I want to get maximum clearance between the pan and axle though, esp important for when I get around to a drop stance. I think I should be able to get a newfound 6-7 inches...

and I think I should be able to cut my pickup tube in half and weld in a section of conduit or something.... anybody see any problems with conduit? if so, any suggestions?

OH, and does anybody have suggestions on a cheap dipstick setup for the rear sump? I'm pondering whether the current stick might work, I think the stick itself would be ok, but need a longer tube. any suggestions for a long skinny steel tube? OH, maybe a fat brake/fuel line... that would be great.

and what to plug up the existing dipstick hole with...

While I'm at it, I think I will bite the bullet and actually pay for parts... but only $65 for a fancy crank scraper to remove the oil slingers, and weld a screen to it to cut off the windage cloud. OH, the site for the thing (this particular part/price was on ebay) said they had a zero clearance Teflon version... Ima gonna look into pricing on that one too... sounds special.

http://cgi.ebay.com/ebaymotors/Dual-cra ... dZViewItem

and
http://www.crank-scrapers.com/New_products.html

I know most research shows that this wont really do much below about 6500 rpm, but it couldnt hurt... I figure I might as well... it might keep some froth down?

I think I will likely put in a bung with a plug for time being for a future oil temp guage? or is this just dumb? I saw mention on a few different sites of such a thing.

OH, and I will definitely be fabricating a slam pan for the bottom of the sump.... I am sick of my pan looking like it's about to die. I want it to be able to take some occasional abuse/mishap without getting split open
'63 with 390 & lots of juice. But never enough. Always want more.
ImageImageImage
rctcomp
Posts: 27
Joined: June 4, 2008, 9:42 pm
Location: Grantsville, Ut

Post by rctcomp »

blackagatha wrote:rrg!
wha.gif
User avatar
Jimbo302
Posts: 31
Joined: June 26, 2008, 3:23 am
Location: Dallas TX

Post by Jimbo302 »

I was curious if I could get any more info on that front sway bar setup? Does it drive well with it?
Truckfarmer2
Posts: 328
Joined: May 8, 2008, 11:01 am
Location: Central Illinois
United States of America

Post by Truckfarmer2 »

Aggie, have you looked into a FE oilpan from a 4x4 truck? They are the rear sump type. If you can't find one locally, I know where to get one.
If you continue to buy imports, where will your children work?
Post Reply