need help with 95 4.6 thunderbird

A place for discussion of off topic subjects. Pretty much anything goes - just keep it civil, please!

Moderators: Casey 65, Kid

Post Reply
95awd2008
Posts: 44
Joined: November 26, 2008, 11:04 pm
Location: kentucky

need help with 95 4.6 thunderbird

Post by 95awd2008 »

well this is what it started doing smothering out loss of power to the point it would not even pull its self. so i towed it home and now it want start at all it cranks over just dont start. so i put new plugs in and checked all the plugwires (used a old plug to test to see if wires had fire) all 8 had fire but looked weak to me the spark was orange/red. changed the coil packs (didnt help). if i crank and crank on it and hold the gaspedal down it trys to hit. but after a lot of cranking it backfired and blew the air filter box apart any help would be great


p.s i hope it ok to post this on here if not just delete it thanks chris
36truck
Posts: 3152
Joined: October 20, 2007, 8:32 pm
Location: Land of Sunshine AZ
United States of America

Post by 36truck »

I've seen a REALLY plugged cat. converter cause a loss of power enough to stop a car. Have you checked out the timing chain/gears.
Tom Williams
95awd2008
Posts: 44
Joined: November 26, 2008, 11:04 pm
Location: kentucky

Post by 95awd2008 »

36truck wrote:I've seen a REALLY plugged cat. converter cause a loss of power enough to stop a car. Have you checked out the timing chain/gears.
i havent checked the timing chain/grears ...but i think the cat. is loose sound like its rattling. could it be the o2 sensor bad? im thinking about changing the crank sensor tomorrow if i get time. can a crank sensor be weak?
User avatar
PFM-64f100
Posts: 1270
Joined: August 7, 2006, 6:37 pm
Location: Haslet, Texas
Contact:

Post by PFM-64f100 »

Being a 95 what is the computer saying? I'm sure by now it's throwing some type of code if not a lot of codes. The little code readers are cheap and can be your friend. You can even buy code readers for ECC-IV and ECC-V computers there just as cheap and a lot easier then counting lights. With it backfiring and blowing up the air filter box I think you timing is way way off. Sounds like a timing belt/chain problem to me.

Just my $.02
64 F100 short bed-style side-460-c6-with side toolbox and Dakota Front Suspension
And a 65 CrewCab

Chris W.

The pickups
65 Crew Cab
http://www.purpleflyingmonkey.com/CrewCab/index.html
64 F100
http://www.purpleflyingmonkey.com/1964- ... index.html
The Torino project http://www.purpleflyingmonkey.com/1971- ... eFile.html
95awd2008
Posts: 44
Joined: November 26, 2008, 11:04 pm
Location: kentucky

Post by 95awd2008 »

PFM-64f100 wrote:Being a 95 what is the computer saying? I'm sure by now it's throwing some type of code if not a lot of codes. The little code readers are cheap and can be your friend. You can even buy code readers for ECC-IV and ECC-V computers there just as cheap and a lot easier then counting lights. With it backfiring and blowing up the air filter box I think you timing is way way off. Sounds like a timing belt/chain problem to me.

Just my $.02
i was thinking it blew the air box apart becouse i keep cranking it over and it built up to much gas in the engine and is not geting the right spark...im going out there right now to see if i can get the crank sensor out
Chico1961
Posts: 27
Joined: February 22, 2009, 9:33 pm
Location: San Angelo Texas

Post by Chico1961 »

Tom, is right on the money! Loosen the exhaust pipe flange at the exhaust manifolds, just enough to let the engine breath, you dont have to take the nuts all the way off, just about a 1/4 of an inch. Be careful when you crank it , you have alot of fuel built up, fire extinguisher handy. It should start. If it starts, dont rev engine, let idle until fuel burns off. Do not hit accelerator at all. Your spark plugs are probably fuel fouled, you may have to pull and dry off with B12. I hope you replaced plugs with motorcraft. Really watch for a backfire you have alot of fuel present. When you seperate the exhaust you will see what I am talking about. Well ventilated area. Good luck ! Holler if you need any help. I am fair on newer stuff, just need help on my slick,
1961 F-100 uni
1961 Futura Ranchero
1961 Harley Davidson Low Rider
1999 cobra convertible
1998 F-150 daily driver
95awd2008
Posts: 44
Joined: November 26, 2008, 11:04 pm
Location: kentucky

Post by 95awd2008 »

Chico1961 wrote:Tom, is right on the money! Loosen the exhaust pipe flange at the exhaust manifolds, just enough to let the engine breath, you dont have to take the nuts all the way off, just about a 1/4 of an inch. Be careful when you crank it , you have alot of fuel built up, fire extinguisher handy. It should start. If it starts, dont rev engine, let idle until fuel burns off. Do not hit accelerator at all. Your spark plugs are probably fuel fouled, you may have to pull and dry off with B12. I hope you replaced plugs with motorcraft. Really watch for a backfire you have alot of fuel present. When you seperate the exhaust you will see what I am talking about. Well ventilated area. Good luck ! Holler if you need any help. I am fair on newer stuff, just need help on my slick,
thanks ill try and loosen up the exhaust this weekend. i had a guy coming out today to scan the computer (check codes) but he didnt show up because the rain i guess if i ever figer it out ill be sure and let everyone know what it was. yes i used motorcraft plugs....thanks chris
User avatar
FORDBOYpete
Posts: 850
Joined: July 21, 2006, 8:30 am
Location: East Central Florida USA

Post by FORDBOYpete »

I agree With Chris 100% both on reading PCM, And probable root cause. I also know modulars are famous for eating
R/H timing drives system. Jasper Engines redesigned & made a new style cam drive gear to rectify that problem,
but they do not sell them, they use them in their own rebuilt 4.6's.

:shock: Please Forgive my stupidity here. :roll:
Without Scanning your PCM to see what it gives you for DTCs or if a thread is started in RAM, but trying
"this & that" to physically diagnose a problem is only making whatever your problem is worse and worse.

When you discover you do probably have a thread, since you ignored the CEL/ MIL for [as you say on the other page]
"forever", do you have a way to translate it's origin & development, or what it is faulting your system from operating?
If not keep reading on.

You need to use OBD I FoMoCo D-Codes. Here is a link to what you need.

http://www.freeautomechanic.com/diagnos ... odes7.html

You can read out OBD I codes by using a VOM hooked to D-Port Data Link & 12v source with a Negative Ground factor.

Analog VOMs will flick or move a needle. Each flick = 1. so 3 flicks = 3 etc.

If you get 1, then a pause, then 1-1-1-1-1, it = 15. CODE 15 = PCM Bad.
It is telling you the ROM in the PCM is corrupted or not functional.

I am not saying that's what your problem is, but I am saying that's where & how you'll find a root or source of your troubles.
The engine operates by a Performance Control Module or PCM. You can not get around that.If you can not find a root source
or primary problem there, you can pretty well rule out computer problems, but I doubt it's the case since
it all began with a CEL/MIL long ago & far away.

But if you rule out any/all PCM or Operating system troubles you'll know you have mechanical problems needing repair.

Backfiring kills Mass Air Flow Sensors by blowing a micro wire measuring air flow rate to hell, so you get no read-out,
which a PCM really must have to run. It's all connected & works together.
Random experimentational diagnostics have
sent many an otherwise perfectly good vehicle to the crusher.

Good Luck with this (these) problem (problems).

FBp :roll:
Change is the Only Constant
Chico1961
Posts: 27
Joined: February 22, 2009, 9:33 pm
Location: San Angelo Texas

Post by Chico1961 »

These codes will be E.E.C. 5 codes. You have driven the car too long with check engine lite on. The codes you get will send you on a wild goose chase! You have to start with basics. Spark, fuel pressure, compression, exhaust backpressure. Once you clean the fuel fouled spark plugs and clear the memory on the P.C.M. Then you can check for a hard fault code. I get customers all the time with Auto Zone said, It needed these parts 500.00 dollars later same problem. Can you fix it? Here are the codes they got. My friend, you have to be able to interpret those codes. They make pinpount procedures. I hope, I don't sound arrogant! Just been doin it for 32 years. Damn, I am old. Wish I would have picked a different proffession, not!
1961 F-100 uni
1961 Futura Ranchero
1961 Harley Davidson Low Rider
1999 cobra convertible
1998 F-150 daily driver
95awd2008
Posts: 44
Joined: November 26, 2008, 11:04 pm
Location: kentucky

Post by 95awd2008 »

Chico1961 wrote:These codes will be E.E.C. 5 codes. You have driven the car too long with check engine lite on. The codes you get will send you on a wild goose chase! You have to start with basics. Spark, fuel pressure, compression, exhaust backpressure. Once you clean the fuel fouled spark plugs and clear the memory on the P.C.M. Then you can check for a hard fault code. I get customers all the time with Auto Zone said, It needed these parts 500.00 dollars later same problem. Can you fix it? Here are the codes they got. My friend, you have to be able to interpret those codes. They make pinpount procedures. I hope, I don't sound arrogant! Just been doin it for 32 years. darn, I am old. Wish I would have picked a different proffession, not!
im probley not the guy for the job..lol i dont have a clue what a E.E.C 5 code is. so it going to be hard for me to read. it might be best for me to strip the car and use the parts for my slick. the t-bird rear cradle swap looks nice. anyone ever used the front susp. out of a t-bird in a slick?
User avatar
FORDBOYpete
Posts: 850
Joined: July 21, 2006, 8:30 am
Location: East Central Florida USA

Post by FORDBOYpete »

Chico 61,
Look, no offense intended here. You are certainly entitled to your opinion. You have every right to express it as you wish.
I must respectfully diasgree. It probably doesn't really matter except in principle. 95awd2008 is apparently
going to use his T-Bird for parts. However, I must reply to comment on inaccuracies I find in this thread.

A-Z & people who rely on it aren't a good reference for anything to me.

The confusion & myths swirling around Automotive Cyber-technology are a result of people unqualified to work with,
or on automotive digital control systems & driveability problems they may represent. It's a science, not Voo Doo Magic.

BUT E.E.C. 5 Codes ? :shock:. . . . AUTOZONE ? :rotflmao:. . . . . 32 years? :hm: . . . . What are you talking about? shrug.gif

All FoMoCo Electronic Engine Control systems are an EEC system. EEC is the abreviation of Electronic Engine Control

EEC systems which do create codes (and not all do) are operating system specific.
EEC IV systems would be CFI & SEFI systems which use speed density logic & codes in older FoMoCo systems.
Many early systems had STAR capability. This onboard ability for systems to self diagnose & Readout it's results.
It thus abbreviates asSTAR = Self Test Automatic Readout.
This began in mid 80's. STAR systems are operating system specific DTC notations. Self Diagnostics atill exist today
in the OBD II PCMs of late model cars.

SEFI is sort of a cross between CFI & TPI speed density, operating systems as FoMoCo developed EECs.

MAFS is where FoMoCo went into OBD I logic and that was around 1993.
That is model and application specific but it makes analyzation very complex so "Uncle" stepped in.
By U.S. Govt. Mandate in 1996 OBD I became OBD II with a uniform code system & "pending code files", as well as
those older fault and/or DTC code presentation such as previous systems also offered from EEC IV onward.

But why am I explaining this ?

Point is a '94 Thunderbird with a 4.6L modular V8 rolled out of Ford's plant equipped with OBD I operating system.
When you get code 15 in OBD I system, it makes no difference if everything mechanical is in perfect order, or not.
Engine will not run correctly & most likely not at all if ROM is scrambled in PCM, which is what a DTC 15 says.

Disconnecting this & that then cranking an engine over to start it further confounds/exacerbates a working PCM.
At the same time it makes no difference to corrupted PCM because if PCM is not working it's not reading or writing DTCs.
Call & response efforts it can not make can not be read or analyzed. Once PCM/ Operating System is corrupted.
Also KAM will not work anymore. KAM or keep alive memory is last resort for diagnostics in flawed systems.

So the more one screws around trying to figure out why there's a problem the worse a problem which existed
or exists becomes as well as the more damage is often inflicted during the shade tree experimentations.

So what I say and what I mean is:
You will not get engines requiring sophisticated operating systems such as OBD I or II to fire up & run well,
if they even run at all with a failed system still wired in, but inoperative for whatever reason there could be.

nono.gif FBp shrug.gif
Last edited by FORDBOYpete on April 7, 2009, 7:10 am, edited 1 time in total.
Change is the Only Constant
User avatar
Greg D
Posts: 10113
Joined: September 13, 2006, 4:39 pm
Location: Podunk Iowa
United States of America

Post by Greg D »

Pete is right about these computer controlled vehicles - he has an extensive back round to draw from. He's just trying to help figure it out the right way. Short cuts will make it worse.
1964 F 100 - I am going to do "something" with it.......

viewtopic.php?f=32&t=15942

1987 Mustang LX Convertible, 2.3 Auto - cruiser.
1994 F 150 XLT 2WD


~ Yes - I adopted another cat..............

Cam L Milan,
You'll be missed my friend.
Chico1961
Posts: 27
Joined: February 22, 2009, 9:33 pm
Location: San Angelo Texas

Post by Chico1961 »

I have an extensive background to draw from also. Image I dont see how dropping the exhaust is going to further confuse the computer. You obviously already have a problem there. It looks really good on paper all your COPY AND PASTED mumbo jumbo down there. But I can tell you from experience, I dont care how badass your computer is, its not gonna tell you that you have a stuffed up exhaust. Thats something you have to try a "shortcut" on.
FORDBOYpete wrote: So the more one screws around trying to figure out why there's a problem the worse a problem which existed
or exists becomes as well as the more damage is often inflicted during the shade tree experimentations.
So Im just wondering...what would become more damaged in my "shade tree experiment" by dropping the exhaust?:hm:
FORDBOYpete wrote:So what I say and what I mean is:
You will not get engines requiring sophisticated operating systems such as OBD I or II to fire up & run well,
if they even run at all with a failed system still wired in, but inoperative for whatever reason there could be.
So you mean to tell me that if you do in fact have stopped up converters ( which doesnt seem like such a stretch to me anyways...
95awd2008 wrote:but i think the cat. is loose sound like its rattling.
) that dropping the exhaust isnt the best way to diagnose that problem?
FORDBOYpete wrote:BUT E.E.C. 5 Codes ? :shock:. . . . AUTOZONE ? :rotflmao:. . . . . 32 years? :hm: . . . . What are you talking about? shrug.gif
What IM TALKING ABOUT is whenever people like you who are scared to spend 5 minutes loosening up the exhaust to easily diagnose the problem decide that it needs something based on what your computer told you and send them to autozone, and then they come to me pissed of because it isnt fixed. I am all about using computer controls to help diagnose your problem, but you cant solely use that, or you will be chasing your tail bud.

And if we are gonna point out inaccuracies we can do that as well... fyi.gif
FORDBOYpete wrote: Point is a '94 Thunderbird with a 4.6L modular V6 rolled out of Ford's plant
Wasnt sure that ford had ever put out a 4.6L modular V6? :oops:




I have never been part of a forum before, but I should have taken my sons advice that sometimes people can be incredibly arrogant. _headdesk__by_Warpedmind125.gif Whenever your ready for round 3... boxing.gif
1961 F-100 uni
1961 Futura Ranchero
1961 Harley Davidson Low Rider
1999 cobra convertible
1998 F-150 daily driver
Post Reply