Page 35 of 47

Re: Steve's 64 Short-bed Project

Posted: April 27, 2020, 7:50 pm
by SteveCanup
Ran out of time this evening...but making progress...
Image
Image
Image
Image
Image

Thanks to everyone for the suggestions and tips. (and encouragement)...I have managed to get the seam welded again. It will have body filler in it but I can live with it. Hopefully tomorrow I can get a little more time free and move this along. I would love to be spraying primer on that side of the bed by tomorrow afternoon.

Stay tuned....

Re: Steve's 64 Short-bed Project

Posted: April 28, 2020, 2:15 pm
by SteveCanup
Well...I sprayed some primer...still some work to do. But the primer helps me to see where it needs more attention...
Image
Image
Image
Image
Image
Image

I still have a few "wonkies" that I will work on....chasing perfection...

Stay tuned

Re: Steve's 64 Short-bed Project

Posted: April 28, 2020, 8:01 pm
by SteveCanup
Managed to get the passenger side sprayed in primer also...
Image
Image
Image
Image

I need to clean the lens on my camera...lol....I will let the primer shrink for a few days.

I will work on the header panel and inner wheel wells in the meantime....

Stay tuned....

Re: Steve's 64 Short-bed Project

Posted: May 1, 2020, 9:29 am
by SteveCanup
I had an hour or two yesterday evening to get in the garage and work on the bed. I sanded all of the outer panels with 220 and filled a couple of low spots. Sprayed a little more primer on the sides. I still have what I call a "wonkie" on the drivers side. I like to wet the primer down and then you can see the imperfections in the shine.

Hopefully, today I will get out there and work the sides a little bit more. I'm trying not to get in a hurry and say/think "that's good enough." I want to get the sides as straight as possible....which might be impossible with my skill set. I will probably block sand the sides to get them right.

I also welded in a small (2"x8") patch onto one of the inner wheel wells and started sanding the inside of the bed. I will not get it as smooth and nice as the outside, but I want to improve the way it looks.

Stay tuned...

Re: Steve's 64 Short-bed Project

Posted: May 1, 2020, 4:35 pm
by 04sd
A tonneau cover will fix the inside of the bed. :D

Re: Steve's 64 Short-bed Project

Posted: May 1, 2020, 5:13 pm
by SteveCanup
04sd wrote:A tonneau cover will fix the inside of the bed. :D
I like that Idea Bill...lol. I did build a tonneau cover for my '66 that I restored in the mid 1990's. I've been seriously thinking of making another one. This thing is "caving my backside in" as far as working on it. I sanded and welded and pounded (on the inner wheel wells) today and made some progress. Still a ways to go....

Re: Steve's 64 Short-bed Project

Posted: May 2, 2020, 7:30 pm
by SteveCanup
Well after several days of sanding the primer off and reworking some of the body work, I shot some more primer on the bed this evening. I am fairly happy with the result. The plan is to spray some color, if white is a color lol, on Monday. Still working on the inside of the bed. It will not be perfect on the inside because I am planning on using the truck. I have beat some of the dents out of the wheel wells and applied some bondo on the drivers side one. I am planning to prep and paint the rear of the cab before installing the bed. I'm hoping to be sitting the bed on by the end of this upcoming week.


More to come....stay tuned.

Oh...here's some pics...
Image
Image
Image
Image
Image
Image

Re: Steve's 64 Short-bed Project

Posted: May 3, 2020, 6:44 pm
by SteveCanup
Planning on painting the bed tomorrow. I want to paint the back of the cab before installing the bed. I have this to deal with first...
Image
Image
Image
Undoubtedly when the bed was hit years ago it pushed it into the cab and caved in this area. It was filled with almost 1/4" of bondo. I dug it all out and hammered it out to this point. I will have to fabricate a patch panel.

Stay tuned....this will never end....lol....

Re: Steve's 64 Short-bed Project

Posted: May 4, 2020, 4:41 pm
by SteveCanup
Done!
Image
Image
Image
Image

Now to get the upper corner of the cab repaired...

Stay tuned...

Re: Steve's 64 Short-bed Project

Posted: May 4, 2020, 6:13 pm
by 04sd
In the first picture of the cab corner it looks like almost zero clearance between the door and cab?
The out side of the bed looks great.

Re: Steve's 64 Short-bed Project

Posted: May 4, 2020, 8:42 pm
by SteveCanup
04sd wrote:In the first picture of the cab corner it looks like almost zero clearance between the door and cab?
The out side of the bed looks great.
Bill...I had to go back and look at the pic...and you're right. I had never noticed. I don't know if there is anything that I can do about that at this point. I welded a patch panel in this evening and coated the whole mess with....you guessed it....more bondo. Thanks for the compliment on the bed...again, I am not a professional...or an amateur....just a "back-yard" hack.

This truck is the "gift" that keeps on giving....lol....but I love it.

Stay tuned....

Re: Steve's 64 Short-bed Project

Posted: May 5, 2020, 7:44 am
by grump
The bed looks good Steve. Looks like you're getting the hang of body work. It seems most people don't care for it but I enjoy it but then again I started learning in the spring of 1967 and I'm still learning. Keep up the good work.

Re: Steve's 64 Short-bed Project

Posted: May 6, 2020, 8:31 am
by SteveCanup
grump wrote:The bed looks good Steve. Looks like you're getting the hang of body work. It seems most people don't care for it but I enjoy it but then again I started learning in the spring of 1967 and I'm still learning. Keep up the good work.
Thanks!

I haven't worked on the truck much the past day or so...Hoping to get time out there today and finish the cab corner. It is challenging because it has so many curves to it and the metal is shot. I have already cut some of the damaged metal out and started welding patches in.

Stay tuned....

Re: Steve's 64 Short-bed Project

Posted: May 7, 2020, 4:23 pm
by SteveCanup
Primered...then painted....
Image
Image
Image
Image
Image

Now to get the bed set back on....We have an area-wide cruise-in Saturday night. It is literally a cruise in...ride up and down main street and you can park, but you can't get out of your car. If you do the Nazi's will shoot you....

Stay tuned....

Re: Steve's 64 Short-bed Project

Posted: May 7, 2020, 5:23 pm
by SteveCanup
Bed setting...this evening...

Re: Steve's 64 Short-bed Project

Posted: May 10, 2020, 2:38 pm
by SteveCanup
Today...
Image
Image
Image
Image

I am going to get the tailgate sanded, painted and installed this week...stay tuned.

Re: Steve's 64 Short-bed Project

Posted: May 10, 2020, 2:51 pm
by SteveCanup
A Video that I recorded yesterday...
https://youtu.be/aftT1IiI-RM

Re: Steve's 64 Short-bed Project

Posted: May 12, 2020, 5:11 pm
by SteveCanup
I can go "tailgating" again...lol. I had painted the FORD letters red, but I'm thinking that I like the clean white look. At least for now.
Image
Image

Now to get the inner bedsides and wheel wells painted and the treks decking back in...

Re: Steve's 64 Short-bed Project

Posted: May 13, 2020, 8:36 pm
by SteveCanup
Today...roof rot repair. I had been putting this off. It was time to tackle it...
Image
Image

That's all I had time for today....it's progress though.

Stay tuned

Re: Steve's 64 Short-bed Project

Posted: May 21, 2020, 8:46 am
by SteveCanup
Not much has happened with the truck in the past week or so...family stuff intervenes. My 15 year old grandson has been visiting this week and my intention (and his) was to get him in the garage and put him to work on my truck. Other things happened instead....

Anyway...stay tuned....