Page 1 of 1

O/T: Source of Used RTJ Gaskets??

Posted: July 7, 2011, 11:47 am
by jamesdfo
Anybody work in a plant where they use RTJ gaskets?? I have an idea that would require a number of R18's, but they are EXPENSIVE to buy new, and R18 is kind of an uncommon size.........would be looking for about ten or so, would prefer in SS, 304 or 316, but could get by with CS. Willing to pay........ a bit

Image

It is a metal "Ring" gasket, used with flanges that have a corresponding groove machined in them. See link below for pics....

http://www.flexitallic.com/pro_metalic_r.html


http://www.flexitallic.com/pro_metalic.html


http://www.smithgaskets.com/ring.html

The size I need is R18, and it's not common (I think that R18 is for 1-1/4" pipe). The "R" number is stamped right on them, on the O.D. as I recall.
**Just had a look online, and an R18 would be used in a 1" 2500# Joint, as well as in 1-1/4" 300# thru 1500# Joints
R18 has an O.D. of 2-11/16", I.D. is 2-1/16"
All sizes/dimensions listed in these tables....
http://teadit-na.com/catalog/index.p...products_id=71




Thanks!
James

Posted: July 7, 2011, 7:53 pm
by Hoofbeat Racer
oddball size James. I could get you countless R24s but would raise some eyebrows about R18s.

Posted: July 7, 2011, 8:51 pm
by jamesdfo
Mark: Yah, I know:(........my buddy Steve works in many gas plants south of Grande Prairie, and he seldom sees any R18's....and even in CS, they are like $15.00 or more new off the shelf......

James

Re: O/T: Source of Used RTJ Gaskets??

Posted: October 29, 2011, 9:17 am
by jamesdfo
Well, the search continues, but upon further thought, I will actually need sixteen :oops:

James


jamesdfo wrote:Anybody work in a plant where they use RTJ gaskets?? I have an idea that would require a number of R18's, but they are EXPENSIVE to buy new, and R18 is kind of an uncommon size.........would be looking for about sixteen or so, would prefer in SS, 304 or 316, but could get by with CS. Willing to pay........ a bit

Image

It is a metal "Ring" gasket, used with flanges that have a corresponding groove machined in them. See link below for pics....

http://www.flexitallic.com/pro_metalic_r.html


http://www.flexitallic.com/pro_metalic.html


http://www.smithgaskets.com/ring.html

The size I need is R18, and it's not common (I think that R18 is for 1-1/4" pipe). The "R" number is stamped right on them, on the O.D. as I recall.
**Just had a look online, and an R18 would be used in a 1" 2500# Joint, as well as in 1-1/4" 300# thru 1500# Joints
R18 has an O.D. of 2-11/16", I.D. is 2-1/16"
All sizes/dimensions listed in these tables....
http://teadit-na.com/catalog/index.p...products_id=71




Thanks!
James

Re: O/T: Source of Used RTJ Gaskets??

Posted: June 9, 2012, 10:17 am
by jamesdfo
BTT^

Soooooo, no one on here works in a plant that uses RTJ's??


Thanks!
James

Re: O/T: Source of Used RTJ Gaskets??

Posted: March 15, 2014, 11:06 pm
by jamesdfo
BTT^