Page 1 of 1

Need help on Cologne V6 Pattern, 2Wd, AOD

Posted: May 29, 2007, 10:47 am
by FORDBOYpete
Okay, Here's a problem I'll never have with a Slick. . . . . :hm:

I have this incredible Aerostar Beater I don't want to part with. It is a 4.0L Cologne Type V6 that runs like the solar system and has 230+K miles. I love my beater. It's a rolling tool shed with tunes, A/C, & creature comforts.

BUT it also has 2 Dana :barf: L/S Differentials one facing forward and one facing rearward, Plus one in the Transfer case that faces both ways because it's a fulltime (partial) 66% X 33% AWD called a 70/30 4X4. . . . .Needles to say the DANA Diffies are about done at 230,000+ miles. I can't see spending $1200 or so to go through both of them. I also have no real need or use for the AWD where I am, but since there is the 3rd fulltime Diffie in the T/C I can't just delete the front diffie & turn off the AWD program. shrug.gif bang.gif :bangin:

I can't get a straight answer where to look for an AOD or A4OD in 2Wd with a Cologne Bolt pattern that I can bolt in to make it 2Wd from the rear Axle or rear wheel drive.

I plenty of feedback on M5ODs, but they're manual & I don't want manual, let alone one of those Crap Can Mazda M5 Clunkers. :barf:
I donated my 88 XLT to the crusher in disgust over the M5OD in it. no.gif :cussing: down_1_Revan.gif

I'm thinking AOD out of a Ranger with a 2.8L or 2.9L because they' Also are the Cologne pattern & came with 2Wd AODs. . . . . secret.gif

Anyway anybody have access to a Hollander Interchange Manual that can help me here? Needs to cover up thru 96 plus Ranger & Aerostar.

Any All Assistance is appreciated :notworthy: worship.gif praying.gif feedback.gif


FBp Bolt.gif

Posted: May 29, 2007, 12:11 pm
by Greg D
I don't have a Hollander handy but it has always been my understanding that with the right flexplate etc. any of the AODs or M5ODs will bolt up to any of that 2.8 to 4.0 family. They do alot of these swaps in in Bronco IIs and Exploders & Rangers. Take a look in the "Serious Explorations" (Ranger/Explorer/Bronco II forum similar to this one) those guys know about everything concerning these things. I looked at getting a 69-74 Capri for awhile and was gonna swap in a 4.0 with a 5 speed in it (shoulda been a fun ride/ ricer my arse, lol!) Hope that helps some, Greg

Posted: May 30, 2007, 1:00 am
by Johnny Canuck
You saying the Cologne matches the small block V8 Pattern Greg? heck everything under the sun must match that pattern including 223's, or is the BS going around this forum is getting as bad as F.T.E... :roll:

Posted: May 30, 2007, 7:05 am
by FORDBOYpete
nono.gif Cologne Pattern only matches Cologne pattern. no.gif

It does not fit BBF, SBF, FE, Y Block, 5 Bolt (early Windsor), Flattie or
the Mazda/ Courrier.

conspy.gif Cologne is a stand alone pattern bs.jpg :bangin: hurrah.gif . . . . Ala Franciose Of course. scared.gif :peepwall: shrug.gif

secret.gif It's part of the World Car :rotflmao: :lol: :roll: :lol:

FBp Bolt.gif

Posted: May 30, 2007, 8:18 am
by Johnny Canuck
Uh huh. That's what I suspected. neener.gif

Posted: May 30, 2007, 9:28 am
by Greg D
Think you misunderstood me JC, what I ment was any tranny from that engine family should interchange. AOD to M5OD irregardless of year and vice versa. Like swapping a M5OD in behind your 2.8 in your 79 Capri or even the 74 capri you have in the back yard that has needed a tranny since 82'. Even if the block pattern were the same they will not interchange with small block trannys, the input shaft is too long.

Posted: May 30, 2007, 6:30 pm
by 61ford
the only automatic that i know of that fits a 4.0 thats not computer controlled is a4ld and you wanna stay far away from those id like to shoot the ford engineers that designed that trans ive got one i hate it all its ever been is trouble.THe later models are computer controlled starting in 95 and ive never been round those but they are supplosely just a revised a4ld so i can emagine there just as bad.If it was me id go manual if i was looking for a trans for a 4.0