Page 1 of 1

If you are using the tranny cooler ports on your radiator

Posted: June 9, 2007, 10:51 pm
by Phil
Today I was driving my Fairlane and a guy yells that I am leaking something.
I hop out and see strawberry milkshake looking stuff coming from my overflow. Seems my rad blew the trans cooling guts inside the radiator and my cooling system is FULL of trans fluid. I think a C6 holds about 16 quarts. I bet its a 50/50 mix now. My trans started to slip too. I am hoping thats not destroyed. The mill is a fresh build, I just dropped some coin to get that done so this will sideline me for a while. :(

Moral:
Get a separate trands cooler :?

Bearer of bad news

Posted: June 10, 2007, 1:34 am
by DanSanDiego2000
I had a customer come into my shop just the other day complaining of a coolant leak. The leak was red like trans fluid, so I thought he was just confused. He had topped off his radiator overflow earlier that morning, and now had a bad leak. Turns out he had poured automatic trans fluid into his coolant overflow, and it had destroyed his upper and lower radiator hoses, and his heater hoses in just a matter of hours.
The radiator hoses can handle pressure, heat, ethylene glycol, but obviously not petroleum based oils. Check your hoses,..... I'd be willing to bet they are as soft as butter now, and just waiting to blow up when you bring the system up to heat and pressure. Maybe just replace them as a preventative measure.
Good luck.
Dan

Posted: June 10, 2007, 9:12 am
by FORDBOYpete
FWIW, :hm:

point.gif The Alleged Transmission Coolers in radiators are just a plain, old, steel tube, nothing more folks. :shock: th_inconcievable.gif shrug.gif

If in doubt take one out, You'll be doing what Heavyhauler suggests. :thumright:

FBp Bolt.gif

Posted: June 10, 2007, 11:45 am
by 64 f100
Anything with rubber is affected radiater caps, heater controls with rubber in the valves etc. As to the transmission, drain it and the torque converter, immediately. Fill with fresh fluid and run it thru the gears , long enought to get most of the coolant mixed in and drain it again. If it comes out fairly clean, then refill and see if it works. Engine needs to be flushed also. Raadiater can be left in truck, by plugging the transmision cooler ports. Bypass the cooler untill you have flushed the transmission, and found out if it's going to work. Once you have it working, install an aftermarrket tranny coooler. One other thing you might want to do, try some transmedic in the transmission. You've already done damage to the rubber parts more than likely, so do the transmission first, to see if it's going to work. It is imperative that you get the coolant out of the tranmisson immediatly, if you want to try and save it. The tranny fluid in the radiater is just nasty, and the damge is most likeley already done. Sequence I would do this in is disconnect tranny lines and put in a bypass hose and plug the coolant tube. Drain block and radiater,fluch with fresh water, and refill with mild radiater flush. Drain transmission and torque converter, and refill with cheap transamission fluid. Start it up and warm the engine and transmission up, then drain all again once you've ran it long enough to get the detergent to clean the engine, and shift the transmission thru the gears, dirve some if you can without the transmssion slipping to much. Flush the radiater and engine as described with fresh water. You may be able to save the hoses and such if done soon enough, but don't count on it. The flush itself is hard on hoses and rubber. I may have some used radiater hoses if you want those. Let me know where to send em.

Rich

Posted: June 10, 2007, 1:47 pm
by Phil
Thanks Rich!

Well this is all actually on my freshly rebuilt Fairlane.

So far I have the cooling system flushed out with a hose.
The rad is out, I ran water through the block and the heater core.
I used some marine clean to try to break down the oil but its pointless.

Last night at 2am I dropped the pan and drained it. No sign of water when I poured it out. I then put a couple bolts on the pan and called it a night but not after I P.blastered the converter plug with penetrating fluid.
This AM I tried to pull the torque converter plug but I managed to strip the head off :roll: I then rotated the mill over by hand to see if it had two. No deal. I then dropped the pan, it was about half full of trans fluid.
I decided to change the filter while I was in there and as I removed bolts some water spilled out. About 1/4 of a dixie cup or so.

The plan now is to button it all up, get the aux cooler in place then run a line line into a bucket of clean fluid and run it into an empty bucket until the old stuff is expelled. I'll then hook up the cooler and drive it and hope to burn off any moisture left over.

Thats about the best i can come up with.
Anything in the converter water will kill?
I suspect the pump may already be dead.

Any other ideas? This is new territory for me. Now you wanna talk wiped camshafts and I'm all about it :roll:

Posted: June 10, 2007, 8:58 pm
by 64 f100
Can't get even some vice grips on the converter drain plug? Not good. I don't know how clean your radiater and engine were, and not sure what the antifreeze will do to your tranny. I would guess if the radiater had no rust and was good and clean, which is not often on one of these old trucks, then you might get by okay. The converter need to be drained, but don't know how you are going to do it as is. No other advice I can think of at the moment. Keep us posted on what you do, and how it turns out. I've had things that looked hopeless turn out fairly well in the end.

Rich

Posted: June 11, 2007, 3:02 pm
by Slick Fan
Man, that sucks. Depending on how far you drove it that way, the water may have oil starved some of the bushings & stuff inside the trans. But it's definitely worth trying to flush the fluid & see how it runs, before throwing in the towel.
Like Dan stated, you might want to keep a close eye on your coolant hoses, or just replace them once everything's flushed well.

BTW, have you guys ever seen what ATF will do to the rubber in a brake system? Scary! :shock:

Posted: June 11, 2007, 5:41 pm
by Greg D
Hope your tranny is OK, if nothing got ate flushing will probably fix it. You may have already thought of all this but..... Auto trannys are pretty sensitive to fluid level/pressure so the slippage could have just been a lack of fluid. I'm sure you didn't drive it too awful long that way or you would have probably noticed the slippage before the spueing "milkshake". If that small amount of coolant would have mixed with the ATF while it was running it may not have galled any surfaces. The engine coolant coulda sucked back into the tranny line as it cooled down also, the tranny coolant lines should have had too much pressure to let any in unless they had a pretty big hole. A pin hole would inject a bunch of ATF into your coolant because of the much higher pressure.