Page 1 of 1

Steering wonders at times...

Posted: May 20, 2013, 9:38 am
by shaff64
are all the 63 trucks known to wonder at time with the steering? it's sometimes a little scary if your your going around curves.... it seems to have a mind of it's own! I had the front end aligned and the gear box adjusting screw tighten up as much as I dare. It really helped but there are times it will scare you if your not really on the ball to correct it fast. Any ideas?

Re: Steering wonders at times...

Posted: May 20, 2013, 10:20 am
by unibody madness
About all you have left is to replace your spring bushings. Other than that,anti sway bars will make a world of difference, and recomended .

Re: Steering wonders at times...

Posted: May 20, 2013, 12:37 pm
by bruceandersson
If your front end is in good shape, there should not be any scarey wandering aroud the road. You can have either some looseness in yiour components or can get the same effect if something is too tight. Check for looseness at the steering wheel first. There should not be a lot of play, if there is use a buddy to watch each part while you move the wheel to find the cuplrit. I've also had mostly frozen kingpins cause problems as bind.

Re: Steering wonders at times...

Posted: May 20, 2013, 2:46 pm
by shaff64
I did have the steering box out of the truck while I was working on it. I took the steering shaft out of the box way back when, and cleaned out the inside of all the old oil. I noticed the lower bearing was worn so I put another in it. But, I tried to put it in with out removing the sector shaft. So, I wonder if I may have damaged the lower bearing in doing so? After that I did remove the sector shaft to square up the steering but I noticed when I tried to tighten up that lower nut on the box too much the steering wheel ( with out the steering arm hooked up) it felt as it wanted to bind up in one spot so, I backed the nut off. I wonder if I may need to replace that lower bearing again and do it right this time?

It has all new spring bushings, king pins are tight, and I also put disc brakes on the front. so everything up there is new.

I just don't know how tight I should run that big nut down on the top of my steering box?

Anyone been there done that?

Re: Steering wonders at times...

Posted: May 20, 2013, 3:00 pm
by ICEMAN6166
shaff64 wrote:I just don't know how tight I should run that big nut down on the top of my steering box?
both of the adjustments -the screw and the big nut- need to be performed to achieve the correct tolerances.

the procedure is specified in the factory manual.
what seems correct by feel and what is read on the inch-pound torque wrench can be a big difference.

Re: Steering wonders at times...

Posted: May 20, 2013, 3:08 pm
by 62galxe
The screw should be adjusted in the centered position or you can get some binding. if I remember correctly the big nut needs adjusted first.

Re: Steering wonders at times...

Posted: May 20, 2013, 3:20 pm
by shaff64
Thanks guys, I will try to look up that procedure and try to adjust myself one more time before sending off the pros.

Thanks for your response it will really help!

Re: Steering wonders at times...

Posted: May 20, 2013, 8:01 pm
by Toyz
Locate and completely read, then follow, the factory procedure for adjustment. As Ice stated, an lbs/INCH torque wrench is required, and adjustments to the input shaft bearing should be made with the steering off center. Sector shaft preload should be adjusted with steering centered, but checked for specified preload throughout the travel. No perceptible backlash should be noted off-center. Remember, lbs/inch, not lbs/foot!
Paul

Re: Steering wonders at times...

Posted: June 6, 2013, 6:17 am
by shaff64
Well, I'm to the point of giving up on the steering box issue. Can anyone tell me where the best place is to get another one. I see LMC has one for around 430.00 I think I'm just going to order another one. Any help finding the best place to get one I would really appreciate it.

Re: Steering wonders at times...

Posted: June 6, 2013, 2:57 pm
by Hunter's 64

Re: Steering wonders at times...

Posted: June 6, 2013, 3:06 pm
by Hunter's 64
I also looked at rockauto.com they have a rebuild service , you send them your old box and they have it rebuilt and return to you for 288.00 , but they send them to this place http://www.larescorp.com/ and they are the rebuilders you may contacr them and see what they would charge you directly? just a thought .

http://www.rockauto.com/catalog/raframe ... ttype=7416


Danny

Re: Steering wonders at times...

Posted: June 7, 2013, 6:52 am
by shaff64
Thank You... I will give this a try