Page 1 of 1

ideal carb for 352

Posted: February 4, 2014, 9:56 am
by therealjoeshmoe
ok i have a 352 with edelbrock single plane intake bored .30 over mild rv cam. and im running an edelbrock 600cfm carb, but i think its not enough for the motor, what would be the best carb for my truck?

Re: ideal carb for 352

Posted: February 4, 2014, 1:17 pm
by foodstick
Joeno, I thought you had fallen of the planet !

Re: ideal carb for 352

Posted: February 5, 2014, 9:19 am
by chris401
therealjoeshmoe wrote:ok i have a 352 with edelbrock single plane intake bored .30 over mild rv cam. and im running an edelbrock 600cfm carb, but i think its not enough for the motor, what would be the best carb for my truck?
My performance preference would be a Holley 600 dp or a spread bore 650dp.

Re: ideal carb for 352

Posted: February 5, 2014, 9:32 am
by therealjoeshmoe
really a 650? mine has a 600 and when i nail it it will fall on its face.. it runs perfect and gets great gas mileage.. but i was thinking it needed at least a 750 but i could be wrong i guess.. any opinions on what would make it stutter when i nail it?? if i hammer it a little slower it will take gas and get with it.

Re: ideal carb for 352

Posted: February 5, 2014, 9:38 am
by therealjoeshmoe
foodstick wrote:Joeno, I thought you had fallen of the planet !
nope im still lurking..

this summer prepare to be amazed..

my truck will be back on the road soon...

woohoo.gif

Re: ideal carb for 352

Posted: February 5, 2014, 12:25 pm
by LM14
It just needs tuning. 600 is right for a 352. I know absolutely nothing about an Edelbrock carb (and don't want to). It's in the transfer circuit between acceleration and cruise, would be an accelerator pump or pump squirter on a Holley, no idea on an Edelbrock.

Size is right, just needs tuning.

SPark

Re: ideal carb for 352

Posted: February 5, 2014, 1:04 pm
by chris401
therealjoeshmoe wrote:really a 650? mine has a 600 and when i nail it it will fall on its face.. it runs perfect and gets great gas mileage.. but i was thinking it needed at least a 750 but i could be wrong i guess.. any opinions on what would make it stutter when i nail it?? if i hammer it a little slower it will take gas and get with it.
you described my experience. I ran into that with a LMC gas tank. Large restriction where line goes into tank. Also fuel pumps like pushing to fuel filter not pulling from. Here is a calculator for carb size recommendation.

http://www.wallaceracing.com/intakecfm.php

Re: ideal carb for 352

Posted: February 6, 2014, 8:08 am
by bruceandersson
A stutter on acceleration is usually the accelerator pump. You really need a strong shot to handle the increased airflow.

Re: ideal carb for 352

Posted: February 6, 2014, 8:45 am
by therealjoeshmoe
ok thanks ill check out the accelerater pump and see but i bought the carb new and it has done this ever since..

Re: ideal carb for 352

Posted: February 6, 2014, 11:51 am
by William-in-St George
The pump shot is adjustable on Edelbrock by moving he shot arm down to the bottom hole. Takes about 30 seconds to do. Careful you don't lose the tiny clip.

Re: ideal carb for 352

Posted: February 8, 2014, 8:35 am
by BarnieTrk
This might help.
Take a look at the bottom of page 3, Adjustments & Troubleshooting:

http://www.edelbrock.com/automotive_new ... 0/1400.pdf

BarnieTrk 8)

Re: ideal carb for 352

Posted: February 8, 2014, 5:45 pm
by cooter
double check that both squirters are pumping fuel when you hit the throttle, could have a shaving plugging a hole. Also check timing, to much advance will do the same. How fast does the advance come on, might need a stiffer spring in the dizzy

Re: ideal carb for 352

Posted: February 8, 2014, 7:40 pm
by hubbtomdaman
Nice Truck

Re: ideal carb for 352

Posted: February 23, 2014, 8:09 pm
by chris401
therealjoeshmoe wrote:ok i have a 352 with edelbrock single plane intake bored .30 over mild rv cam. and im running an edelbrock 600cfm carb, but i think its not enough for the motor, what would be the best carb for my truck?
Did it work out?

Re: ideal carb for 352

Posted: February 28, 2014, 1:11 am
by totten
Sounds to me like you need to lean the Edelbrock 600. They are jetted for perforance. Change the rods from the top of carb.Also slow the secondarys down by a spring change. Spring kit has 5 diff. springs. Check your manual or did you get a cd for a manual? Go 1 step lean to test, keep going until you lose driveabily then back up 1 step. You will have to buy rods and jets kit. Good luck,Tony I had to jet a Edelbrock 500 that way. Ran great!

Re: ideal carb for 352

Posted: February 28, 2014, 10:05 am
by randyr
I used to have the Edelbrock #1406 600cfm carb/Performer intake on a 352 in my '66. Took a while for me to get it to run right. After talking with an Edelbrock tech, he said the carb likes 5.0psi of fuel pressure but the stock Ford fuel pump usually cranks out 8.0psi. I put a fuel pressure regulator on it and cranked it back to 5.0psi. Worked much better but mpg's still sucked! Ultimately jerked it all out and put in EFI 5.0/AOD. It was a good move for me. :D Good luck.

Re: ideal carb for 352

Posted: February 28, 2014, 11:55 am
by William-in-St George
All good advice. Are you using a single plane intake? If you are I'd recommend you get a dual plane either stock or aftermarket. I use Edelbrock cause they are really light weight and work. Stock is also good but you need an engine hoist to install it.