Page 1 of 1
Dewalt Dry CUt Saw
Posted: May 22, 2014, 10:44 pm
by kstones63
Does anybody have any experience with this saw?
http://www.amazon.com/DEWALT-DW872-14-I ... ry+cut+saw
I am planning on buying one and I wanted some feedback before I buy one.
I am getting ready to build a new trailer for work and this would save a lot of time cutting the 2x6x1/8" tubing for the frame. I have heard that they are supposed to be way better and faster than an abrasive saw.
Kevin
Re: Dewalt Dry CUt Saw
Posted: May 23, 2014, 11:47 am
by Truckrat
Kevin, I have a Makita chop saw I have used for 25+ years and I have
cut all kinds of pipe, tubing, angle, channel, etc with it. Depending on the
material you are cutting, the blades will last quite a while. Quality of blades
(discs) varies a lot too. You can get ones with a webbing material in them
and ones without. I am due to buy some new ones too so I will get to see
how much more they cost now than when the last time I bought some.
I can cut angles with it too, up to 45 degrees. I am sure you will like
using a chop saw to cut your stock with over other types. I have been
pleased with mine. Makes it a lot less work to cut metal. Just my
TR
Re: Dewalt Dry CUt Saw
Posted: May 23, 2014, 12:15 pm
by LM14
Gary, I think the saw he's looking at uses a different blade and runs a lot slower than a normal chop saw.
That being said, I think blades run anywhere from $80-150 a piece. I think you can have them sharpened if you don't knock the carbide teeth off of them.
If I were making the change in chop saws, I would look at a wet cut saw with the opposite turning blades. They cost a bit more but cut very smooth and don't throw chips everywhere.
http://www.amazon.com/J-F225-1-Horsepow ... ZJMZJABY3H
SPark
Re: Dewalt Dry CUt Saw
Posted: May 23, 2014, 10:01 pm
by kstones63
Gary, I have a Makita chop saw but I just don't like the mess with them. I have heard great things about these metal cutting saws and have heard that they are faster and cleaner than an abrasive chop saw.
Steve, That wet cutting saw would be the ideal way to go but I am not sure that it is in the budget. I will check into them a little more and see if I can afford to do that right now.
This trailer is already going to cost a small fortune to build the way that I want it and I have to build it before I can sell my work truck and the trash trailer to recoup the costs. I am going to build a goose neck trailer with a 4x4x8 dumping trash bin on the back of it. It will be a flat bed with a lot of tool boxes on it and a storage for sheet rock and plywood over the goose neck part.
Kevin
Re: Dewalt Dry CUt Saw
Posted: May 23, 2014, 11:38 pm
by LM14
I couldn't afford the wet cut when I had to replace the old chop saw. I ended up with a regular Milwaukee chop saw and the associated mess.
I thought the wet saws were nice and I want you to have the best stuff available! I'm thoughtful like that.
SPark
Re: Dewalt Dry CUt Saw
Posted: May 24, 2014, 6:34 am
by 6166 Junkyard Dog
sorry Kevin I have no input since I still use a old Dewalt Chop Saw that's has been cutting for the past 20 years,, they do make good products or have in the past,, these days it's hard to say maybe se If someone local has it for say and give it a cut run,,, since if there is a problem you can go directly to them instead of having to deal with Amazon over the internet or phone problem if one occurs.........f
Re: Dewalt Dry CUt Saw
Posted: May 24, 2014, 7:53 pm
by Max
Kevin, I have the Milwaukee version (Milwaukee 6190) for a little less than a year now and absolutely love it. I've made a lot of tow bar racks, fire extinguisher mounts, etc. for the airport I work at part-time and this sucker cuts like butter. Virtually no scabs/slaggy remnants to clean up, just cut and weld away!

Re: Dewalt Dry CUt Saw
Posted: May 25, 2014, 10:47 am
by kstones63
Someone had recommended the Milwaukee but I can't find it anywhere now. If I find a site for it, they are out of stock. That is why I started looking at the Dewalt.
Kevin
Re: Dewalt Dry CUt Saw
Posted: May 25, 2014, 12:10 pm
by jamesdfo
Kevin: Will you actually be able to cut through all 4 sides of 2"x6" tubing with that saw in one go? How about Mitres??
Personally, even though it will be more $$ upfront to purchase, (might keep an eye on CL for a decent used one) I would be looking @ a horizontal bandsaw......quieter than a chopsaw, lik the dry saw, no sparks, and the blades cost a fraction of a new wheel for a drycut saw. Several years back, I bought one because I was tired of the noise, sparks & mess from the abrasive wheel chop saw I was using (not to mention the abrasive wheel chop saws accuracy on cuts was not great, particularly on mitre cuts)......so I bought a 5"x6" horiz band saw, and I'm quite happy with it.....my only regret is not going a size or two bigger than I did, but it fit my budget:)
This is the model I bought (but from a different Co), not sure if they sell in USA or not, but Jet has similar models, the dual swivel was what sold me on this one...might also look @ Grizzlytools.com
http://www.kmstools.com/king-canada-5-x ... andsaw-387
Grizzly
http://www.grizzly.com/products/category/410000
Jet (PITA, no pricing on webpage, but you can clik on
buy online or
find a dealer to get pricing
http://www.jettools.com/us/en/c/metalworking-sawing/240
Re: Dewalt Dry CUt Saw
Posted: May 25, 2014, 2:00 pm
by kstones63
The Dewalt specs say that it will cut a 2x6 tubing on straight cuts. I am sure that it won't cut the 2x6 on a 45 degree miter. IT uses a 14" blade.
I have a small horizontal band saw right now but it isn't big enough to handle that kind of material. It doesn't cut straight on large pieces. I have considered getting a really saw like your pic and I am sure that it would handle the job. I am also starting to look for a box pan brake and some other tools so I am trying to get the most that I can on a budget.
Kevin