Page 1 of 1

Rag Joint/ Steering Coupler Confusion

Posted: August 6, 2014, 7:36 am
by ThinLizzy13
My truck (66 F250) hasn't had steering for a while and I finally got around to tearing into it. I originally thought just the rag joint was bad (it is), but once I got things apart, it looks like the steering coupler(I think thats what its called?) is just rotating around the spline on the steering gear box. It doesn't matter if I tighten it down, it just won't grip. It's the metal piece under the rag joint near the number 2 in the picture.

Image

I have a couple questions about it I hope someone can help me with.
1) Its got some space between the bottoms of the coupler and the gearbox. Should it be snug down to it?
2) I've seen on a couple different sites that said the steering coupler (C6TZ-3A525) is different for trucks after serial number 900-001, mine is 873-851. Whats the difference between them and where can I find one for before serial 900-001? (if this is true)

Thanks in advance for any help. This has been driving me nuts and that coupler is a b!tch to get off! :cussing:

Re: Rag Joint/ Steering Coupler Confusion

Posted: August 6, 2014, 11:40 am
by ICEMAN6166
sounds to me like either one of the splines may be worn out especially if they have been turning on each other.
hopefully its the easy one on the coupler.

#1
the bolt controls the placement on the gearbox shaft
the bolt holding the coupler to the gearbox must be removed, there is a groove on the gearbox shaft spline that it rides along and the coupler cannot be removed until the bolt is out.
then you need to remove the 2 nuts from the rubber part
after that pull the steering wheel back out of the tube enough to get the coupler off the gearbox shaft, when the flange on the steering shaft is clear then you might need to open the split in the coupler some to allow easy removal.
#2
the difference in the 2 couplings is the the pins in the rubber
one has a fat and a skinny pin, the other both are the same.

btw it is wise to mark the steering wheel location befor removing so it ends up in the same spot after reinstalling the new coupler.

heres a pic i took of one of the parts trucks i had
someone who was not wanting to buy a new coupler, they just cut out the rubber and bolted the metal pieces together
very bad
Image

Re: Rag Joint/ Steering Coupler Confusion

Posted: August 6, 2014, 11:43 am
by banjopicker66
I think the coupler is not the right one.
I compared some photographs of my original steering setup, the Bendix PS setup I had for a couple of years, and the Ford/Saginaw power steering setup in there now, and they are all slightly different.
Yours looks (or SEEMS to look) more like the one for the '73-'79 power steering option.
I think that the spline counts and/or sizes may be different in between the different gearboxes, which would contribute to failure, if the one on there now is not correct for your steering gear.
Also, the bolt that crimps the coupler onto the gearbox splines is incorrect, so that leads me to think there was something done not quite right.

Re: Rag Joint/ Steering Coupler Confusion

Posted: August 6, 2014, 4:17 pm
by 6166 Junkyard Dog
splines are the same regardless of what gear box or year matching up,, earlier ones had a small and big pin, later ones had both pins same size and then also some later ones had a plastic sleeve that went around the pins,, also some had a small wire for a ground..

Re: Rag Joint/ Steering Coupler Confusion

Posted: August 7, 2014, 7:20 am
by ThinLizzy13
Thanks for all the help guys, this truck would be a lot more difficult to work on without this site :thumright:

Banjopicker - It seems like there isn't something quite right about the coupler that was on there. It looked like it was only halfway on, and any couplers I looked up seemed a little different. There was also alot of other stuff done on this truck not quite right by the PO lol.

Luckily the splines in the coupler were ground out and the steering box gears seem to be ok. Hopin to have the new coupler on today and the truck back on the road.

Re: Rag Joint/ Steering Coupler Confusion

Posted: August 7, 2014, 10:12 am
by banjopicker66
Excellent! Glad it is an easy fix for you, it is sure not fun to think about changing a gearbox.

Re: Rag Joint/ Steering Coupler Confusion

Posted: August 8, 2014, 9:12 am
by ThinLizzy13
Yea I was dreading the thought of a new gearbox. It's on now though and everything is snug and tight :steering:

Re: Rag Joint/ Steering Coupler Confusion

Posted: August 8, 2014, 4:20 pm
by GarageTime
Anyone notice the NG under the truck pictured with the rag-less joint. :lol:

NOT GOOD!

Re: Rag Joint/ Steering Coupler Confusion

Posted: August 8, 2014, 4:58 pm
by banjopicker66
Yep. Very bad.
See Iceman's comment in post Number 2.