Page 1 of 1

engine miss under load

Posted: August 28, 2014, 9:08 pm
by slixtyfive
This isn't totally off subject since it is regarding a ford engine but since it's not in a slick i'll post here.

I have a '51 F1 pickup that i put a rebuilt 302 in several years ago. I don't drive it much and in fact hadn't driven it in a couple years until this summer when i decided to drag it back out. After changing the oil, I pulled the distributor to prime the engine (marked everything well to make sure i put it back in the same) and all went well. Dropped the dist back in, fired up fine and went for a short drive. Ran fine on this drive but i noticed excessive exhaust leaks(it had block hugger headers with original gaskets that came with the headers - ie low quality) and decided i better fix that before driving it more to make sure i didn't cause any damage under the hood. So, a couple weeks ago i pulled the headers off, cleaned up the surfaces and installed some nice new header gaskets and collector flange gaskets and put everything back together. Got in with the Mrs to go for a 'quiet' ride a couple days later, pulled out of the driveway and upon acceleration, snap crackle and pop!!!! (WTH!!) Turned around and went back in the driveway thinking a plug wire was crossed or something (had them off to remove the headers) but nope, couldn't happen as the wire lengths dictated exactly where each goes. Then i thought well, maybe when dropping the headers i broke/cracked a plug. Bought new plugs and just tonight replaced them but still has mis-fire under load. But not on idle or when increasing RPM with no load (neutral in the driveway).

Any thoughts? How do i get a mis-fire from changing exhaust gaskets??!!! Must be a coincidence but either way, very frustrating!

For reference, it has an Accell alum distributor. All components(complete distr with cap, rotor, points, cond) were new when engine was put in about 8 years ago. I'll probably start changing things out but just thought i'd try to get some input here to hopefully shorten the fix time/costs. Probably should be looking at carb too...?

Thanks

Re: engine miss under load

Posted: August 28, 2014, 10:09 pm
by Pack Rat
Go back and check firing order. 7 and 8 crossed?

Re: engine miss under load

Posted: August 29, 2014, 10:45 am
by ICEMAN6166
had a similar issue a few years back, was arcing between two of the contacts inside the cap. replaced cap and was fine ever since.
if you look up in the cap you can see the carbon track between as a big black spot.

Re: engine miss under load

Posted: August 29, 2014, 11:38 am
by slixtyfive
Pack Rat: I don't think I could have crossed the wires as they were custom fit and only the correct one will even reach #8 (didn't remove them from the cap) but I will double check again tonight.

Iceman: I looked inside the cap for that but will admit I didn't have very good light. Will check that again tonight too.


Thanks for the tips.....

Re: engine miss under load

Posted: August 29, 2014, 7:27 pm
by slixtyfive
Checked both again and appear to be OK.

Re: engine miss under load

Posted: August 30, 2014, 9:17 am
by mercuryv8
Based on my recent experience, I would buy a new cap and rotor in. Check all the plug wire ends to make sure one didn't pull apart.

I bought a truck that had been sitting for quite some time. The cap and rotor were in almost new shape when parked. The cap and rotor looked good. But I had a miss. The engine ran a lot better after 20 or 30 min on the road. Which made me check out all sorts of unrelated systems. After finding someone smarter than me I replaced the 6 dollar rotor and the truck runs great.

Nic

Re: engine miss under load

Posted: August 30, 2014, 2:16 pm
by slixtyfive
The thing is that it originally ran fine when i first stared it up after sitting a while. Now it still might be what you suggested and i'll probably try replacing those.

But i was also messing with it a today and it wasn't as bad and in fact after getting through a low rpm it went away (basically mis-fired once and then was ok until shifting again and going through that rpm range again). So i'm thinking maybe vacuum advance isn't working right.....

Re: engine miss under load

Posted: September 3, 2014, 9:23 pm
by slixtyfive
OK - so it turned out to be a plug wire 'crossing' but it was 5/6, not 7/8. I don't understand how this happened since the wires were 'cut to fit' and although the longer ones could clearly be put on a closer plug, when starting with the shortest and working toward the back, they could only reach the 'correct' plug. I only had them off the plugs, not off the cap, during header gasket replacement. When I said I checked it above all I really did was check the wire lengths - I didn't actually check the order on the dist cap.

I'm assuming my wife is messing with me...... moving plug wires around to drive me crazy!!! :shock:

Re: engine miss under load

Posted: September 3, 2014, 10:56 pm
by LM14
Let's go with that story, it's probably her fault!

SPark

Re: engine miss under load

Posted: September 4, 2014, 12:10 pm
by Toyz
Yeah, divorces are cheaper than plug wires anyway!
Paul