Page 1 of 1

1993 pickup 300 six question

Posted: December 9, 2015, 3:29 am
by Kid
I just bought a 1993 F-150 Short box and it is going to be my Daily driver and I have a few questions! I want to build the 6 up a little? Can I do much to it? What is the wheel bolt pattern, ( I dont have it home yet, Going to go get it this weekend ) I want to run some chrome wheels and tires on it that I have in the summer. It is a pretty clean little truck, Has minor rust in the front fenders at the bottom rear of the wheel opening so that will be an easy fix!....................>Kid

Re: 1993 pickup 300 six question

Posted: December 9, 2015, 6:29 am
by ThinLizzy13
Sounds like it's gunna be a good truck. Wheel pattern should be 5 x 5.5

Re: 1993 pickup 300 six question

Posted: December 9, 2015, 7:27 am
by bruceandersson
I think the 93 is injected, so I think your best mod would be to tune the computer. It should already have the split exhaust manifolds so it has the ability to breath better than older engines. The wheels are the same bolt pattern as the slicks, they changed this in 96 or so to a metric pattern.

Re: 1993 pickup 300 six question

Posted: December 9, 2015, 1:10 pm
by Toyz
Fenders are cheap enough that I wouldn't consider rust hole repair. Like any other vehicle, tuning can be of value if done by the right person. I don't know of many experienced people providing tuning for the pre- OBD II sixes. Along that line, be aware that, much like the slicks; Ford made significant changes in the '94 trucks, and again with the OBD II trucks. Wheels do n fact retain the ancient near-zero offset; bolt pattern changed with the advent of the '97 new body style in January '96, although the old style "Heritage" trucks were produced into '97. Check the dasboard mount brackets at the bottom of the ends of the dash, especially passenger side. If broken or cracked; repair before it gets expensive! Check for recalls affecting your truck!
Paul

Re: 1993 pickup 300 six question

Posted: December 11, 2015, 4:41 pm
by Alan Mclennan
Don`t forget the pic`s Darrell! :D

Re: 1993 pickup 300 six question

Posted: December 11, 2015, 8:22 pm
by slick4x4
I have a parts truck for you
Has a six & five (I think) speed
guy drove it here... I'm going to make a trailer out of the bed.... Someday....

Re: 1993 pickup 300 six question

Posted: December 12, 2015, 10:35 am
by 36truck
The 300 6cyl are great little trucks. They run forever. The older 300's you would do headers & intake & carb to hop them up. Not very well versed with the fuel injected motors.

Re: 1993 pickup 300 six question

Posted: December 12, 2015, 12:39 pm
by Truckrat
Cool deal Darrell! Not much difference bodywise from my 85 other
than the front grill area between the two. LMC has a lot of stuff to fit them.
What color is yours? Is it manual or auto trans? Pics please! TR

Re: 1993 pickup 300 six question

Posted: December 12, 2015, 2:53 pm
by Kid
Thanks guys. It has an auto in it and the front fenders rust is pretty minor but I can buy new ones for $60 so not going to waste time fixing, I will just replace them. Just going to see if I can find someone to look into tuning the computer a little. It is going to be my daily driver so not going to do much till spring when I get my 65 out. It is a nice little truck, blue in color and runs out pretty good. I will see if I can get a pic of it here somehow...................Kid

Re: 1993 pickup 300 six question

Posted: December 12, 2015, 7:04 pm
by Toyz
Might look into Wester's Garage or one of the Tweecer forums.
Paul