Trans and Ignition Questions
Posted: June 7, 2020, 4:49 pm
Hello Everyone,
I just got my F100 back running after 2 years chasing ignition and fuel problems (got discouraged and let it sit.) So I'm going to get it driving again. I have a few questions for those more familiar with these old trucks, as I've only ever worked on my truck.
I don't have much experience related to points ignition: I ran an Accel points eliminator for years until they started acting up, couldn't get it to work right so right now it's got all new Echlin points, condenser, coil, plugs, wires, cap, rotor etc. Just rebuilt the carb. Runs pretty good. I set the points initially with a feeler gauge at .019. Now I have a loaner dwell meter (that is unproven) and it's showing dwell at 550rpm at 40 degrees, should I mess with it? Also noticed they must be out of alignment because it's hitting high on the movable side of the point...how do i get it centered?
Now when I drive it it runs pretty good but when you let off the gas and cruise downhill @2-2500 RPM it snaps pretty loud out of the exhaust. It clears up if you keep a little throttle. It runs worse if I play with the timing in either direction. I thought it might be lean for the RPM so I fattened up the fuel/air to 2-1/4 turns on the autolite 2100, it helped a little. What else could it be? Valve lash maybe?
Transmission Questions: It has a 292 with a 3 speed trans. I know it's been swapped because the door tag said the truck has optional overdrive and the switch is still under the gas pedal but the trans looks nothing like what's in the shop manual. I'm trying to ID the trans. It has a 9 bolt side cover, shifter linkage on the side, non-syncro first. Side cover says AB-2227-B. Can't find a ID tag on it. Any idea what it would be? I'd like to get it rebuilt at some point.
It leaks oil pretty good. Can't tell if it's coming from the Y or the 3 speed or both. But it'll make a good puddle in 5 minutes of idling at temperature. I noticed it's collecting at the lowest point of the bell housing... then loading up the crossmember and axle where it drips from. I cleaned the bell housing off really well and theres a small hole in it, dead center, perfect hole..like it was on purpose...and oil collects there. Is that some kind of factory weep hole?
Thanks sticking out the long read and have a good evening!
I just got my F100 back running after 2 years chasing ignition and fuel problems (got discouraged and let it sit.) So I'm going to get it driving again. I have a few questions for those more familiar with these old trucks, as I've only ever worked on my truck.
I don't have much experience related to points ignition: I ran an Accel points eliminator for years until they started acting up, couldn't get it to work right so right now it's got all new Echlin points, condenser, coil, plugs, wires, cap, rotor etc. Just rebuilt the carb. Runs pretty good. I set the points initially with a feeler gauge at .019. Now I have a loaner dwell meter (that is unproven) and it's showing dwell at 550rpm at 40 degrees, should I mess with it? Also noticed they must be out of alignment because it's hitting high on the movable side of the point...how do i get it centered?
Now when I drive it it runs pretty good but when you let off the gas and cruise downhill @2-2500 RPM it snaps pretty loud out of the exhaust. It clears up if you keep a little throttle. It runs worse if I play with the timing in either direction. I thought it might be lean for the RPM so I fattened up the fuel/air to 2-1/4 turns on the autolite 2100, it helped a little. What else could it be? Valve lash maybe?
Transmission Questions: It has a 292 with a 3 speed trans. I know it's been swapped because the door tag said the truck has optional overdrive and the switch is still under the gas pedal but the trans looks nothing like what's in the shop manual. I'm trying to ID the trans. It has a 9 bolt side cover, shifter linkage on the side, non-syncro first. Side cover says AB-2227-B. Can't find a ID tag on it. Any idea what it would be? I'd like to get it rebuilt at some point.
It leaks oil pretty good. Can't tell if it's coming from the Y or the 3 speed or both. But it'll make a good puddle in 5 minutes of idling at temperature. I noticed it's collecting at the lowest point of the bell housing... then loading up the crossmember and axle where it drips from. I cleaned the bell housing off really well and theres a small hole in it, dead center, perfect hole..like it was on purpose...and oil collects there. Is that some kind of factory weep hole?
Thanks sticking out the long read and have a good evening!