Page 1 of 1

hard spot in the road..

Posted: October 26, 2007, 11:27 pm
by dwbr
im at a spot in my engine rebuild, have been working this over in my head till i cant even focus at werk, i started my project small and it quickly spiraled out of control, im at a point where i need to decide to go with a stock 460 crank and rods, pistons bored 40 over or spend another 900 bucks and get the stroker kit with forged rods,pistons, making it a 513. ive allready got all the good bolt on's, edelbrock cam, intake, carb, c9 heads, headers, alum radiator,etc.. the list goes on and on, only thing on the motor that will be original is the block,,one side of me see's the 460 and its power, and what im really going to be doing with it,, but im almost positive at some point im going to be thinking, wonder what that 513 would be like,, whats another 900 bucks more? im almost at the point to just toss a coin...
________
Chevrolet Brookwood specifications

Posted: October 27, 2007, 12:28 am
by Xcessive
if budget permits I'd go with the stroker man.

Posted: October 27, 2007, 12:44 am
by shawns fords
900 bucks is a steal for a stroker kit, I usually see priices for cranks alone for that much. a good set of pistons will run you a good 500 bucks esp forged ones, I havent seen a kit yet for that cheap for either of my engines, I hope the quality of the stroker kit parts is good.

Posted: October 27, 2007, 6:20 am
by Greg D
Only thing that you might want to think about, is the cam, heads and the rest of your parts up to the 514? I'd do it though even if I had to get another cam. Don't know what you were gonna run but you may need a bigger carb too.

Posted: October 27, 2007, 7:49 am
by dwbr
the stroker kit isnt 900, its just 900 more dollars from the cost of the new 460 hardware, .. budget,, its close, i still want to buy rims and tires before i put it back on the road, top end hardware is solid, c9 heads with 3 angle valve job, stainless valves, bowl blended etc, crane stailess roller rockers, hardede pushrods with guides,edelbrock rpm cam, eldelbrock rpm intake, edelbrock performer 800 cfm carb,k&n extreme air filter.. i think the thing that is starting to bother me is i have spent as much money on the engine as i have on the whole truck,, know what i mean ?
________
First-generation Taurus

Posted: October 27, 2007, 8:46 am
by Phil
Is that the Ohio crankshaft setup? $1300

Man I spent more on my Fairlane engine than the car, the interior and paint combined cause I broke it 3 times in a year.

I'd be afraid to spend on a big one and build it myself.
I know I'd mess up on something stupid and have to redo it.

Posted: October 27, 2007, 9:47 am
by shawns fords
OK I see, you have spent a fortune already. might as well spend another 900 for them extra 40 cubes. but then again. do you really need them? is it a full out drag truck? so many people buy a stroker kit just to say they have one yet they dont even need the fuckin thing. I plan on building a stroker engine myself but its for a Drag car. I will be going from 429 cubes to 514 or more. if I already had a 460 crank. I would just run that instead. As long as its a good piece of metal still

Posted: October 27, 2007, 10:50 am
by dwbr
shawns fords wrote:OK I see, you have spent a fortune already. might as well spend another 900 for them extra 40 cubes. but then again. do you really need them? is it a full out drag truck?
you see thats just it, no its not going to be a full drag truck, i plan on taking it to the track, on street night with the guys, they have mustangs, and vettes,..but i also plan on driving thru the sonic on sat nights,..and mine started out as the 429, then i decided to go 460, and then i started looking at the strokers,,my little mind goes berzerk, if i get the stroker i can never say, man i wish i hadda, but then if i get the stroker will i say, i didnt need all that,, hmmm.. i think im just going to go with the stroker
________
MT-100

Posted: October 27, 2007, 9:16 pm
by jeepbut
The hell with new wheels------STROKE IT !!!!!!! Thanks, Lyman.

Posted: October 28, 2007, 5:08 pm
by Jarrod
If 900 won't kill your budget then stoke the thing. But often times adding more cubic inches can lead to other problems. You have good heads for the 460, but will those heads support the 514? Same thing with the cam. The additional cubic inches will change the dynamic of the cam and how it acts during the RPM range? Will your carb and intake run out of steam at the upper end of the power band with the 514? the list goes on. Will the additional power destroy the rest of the drive train when you get on it? A stroker is cool and I want to put a stroker 428 in mine. These are all questions that I need to figure out.

Posted: October 28, 2007, 6:35 pm
by Uncle Skip
Doug.
Give me a call. I need to introduce you to Dale here in Houston. He's doing the same thing and he has extra parts for sale..... aluminum heads..... and who knows what else.
You need to meet him.
And, get in touch with FordboyPete. He's the resident expert on the 460 conversion.
Skip

Posted: October 28, 2007, 7:34 pm
by FORDMANLCRACKEL
Here's some interesting reading, it might help http://www.highflowdynamics.com/ and www.460ford.com
but to answer your question, just skip 514 and go for 545 stroker.

Lonnie

Posted: October 30, 2007, 12:19 am
by blackagatha
get as much out of it as you can!

I put over $3000 into my 390. It's maybe a bit warmer than stock... it makes me sad that I didn't go all the way. SOMEDAY I will have to yank it out again and "upgrade" it. For the time being though, it's a good thing that it's mild, if nothing else, it isn't chugging the gas, it is just drinkin real fast!