Page 1 of 1
Auto tranmission help
Posted: January 3, 2008, 9:04 am
by willy3486
Heres a question for you mechanics. I have a 91 Mazda pickup. I think its the last year before they made the ranger the same. Here is some background on it. I just got it about a month back. I had the carb changed out to a webber, and the carb had the wrong jets. But I am suppose to be having the correct ones sent to me. I got a mechanic to put it on and give it a tune up,going through it. Anyway it runs fine but before today after it was warmed up, it run rough probably due to the jets and the choke needs some adjustments. Today I drove it to work and the same old crap. But the difference today it got to where it wouldn't hardly pull. The engine was running fine but I had to go to about 3-4 k rpm to get it to pull at times compared to 1500-3k rpm normally. But it wasn't slipping. It seemed to run fine just no power to get up the hills and it got to where I couldn't get it over 30-40. I checked the transmission stick and I think it needs some. I can't tell if it has enough or that when I put the stick in after cleaning it that it gets some on it making me think it has some. I am thinking that it gets some on it throwing me off. What do you think folks. It got to where it wouldn't go over 60 then 50 and now about 30. But engine wise it runs smooth. I am going down the road to a store when it opens and get some tranny fluid just to see. I had a caviler that did the exact same thing and I added tranny fluid and it worked great until I solid it about 5 years later.
Update I let it set for about 1 1/2 hours and the transmission fluid is op where it should be . But that is with it not running. So it will probably go down I am guessing when I start it. Am I correct?
Posted: January 3, 2008, 11:07 am
by Slick Fan
Your dispstick should tell you how to check the fluid level...with it idling in park, or otherwise. I haven't seen an auto tranny dipstick yet that didn't want to be checked with the engine running.
The fluid level will always read high with the engine off.
It helps to look at both sides of the dipstick when checking fluid level. Quite often, one side will get wiped on the side of the tube & give a false reading, where the other side reads more true.
Posted: January 3, 2008, 12:09 pm
by willy3486
Thanks for the reply. I checked it again and it still looked low . I went to the store and got some quarts. I put in one and tried it out. It drove better but I am going to check it again later. I think it will be fine now. I am not used to Auto transmissions needing fluid and it seemed odd. But who knows how long if ever that it had been checked. I checked it when I got it but I misread it I think , I was use to my other ones.
Posted: January 3, 2008, 7:32 pm
by Phil
Are you losing fluid due to a leak?
I had my tranny cooler inside my radiator burst.
THAT was a huge disaster.
Posted: January 3, 2008, 9:03 pm
by Greg D
Automatic transmissions have a fluid & filter change interval just like engines, newer stuff could be different. Most I have had are in the 25 -30,000 mile range. Auto trannys hate 3 things, too much heat, dirty/burnt/low fluid, low pressure due to a clogged filter. I have heard of them running 200-300,000 miles with proper maintenance and seen alot go out at 125 to 150,000 miles if not taken care of. I have seen people take meticulous care of a car and all but the fluid level ignore the tranny only to have it blow at 130K when the rest of the car is near perfect and be completely confused by this. One other note, don't EVER let anyplace talk you into flushing an automatic transmission, drop the pan and change the filter too.
Posted: January 3, 2008, 9:25 pm
by ICEMAN6166
[quote="Greg D"]
Auto trannys hate 3 things, too much heat, dirty/burnt/low fluid, low pressure due to a clogged filter.
theres a 4th thing they hate, that is me and the feeling is mutual. 
Posted: January 3, 2008, 9:30 pm
by Phil
ICEMAN6166 wrote:Greg D wrote: Auto trannys hate 3 things, too much heat, dirty/burnt/low fluid, low pressure due to a clogged filter.
theres a 4th thing they hate, that is me and the feeling is mutual. 
I have 5 dead auto trannys in my garage.
I'm feeling rejected myself
Posted: January 4, 2008, 1:48 pm
by Slick Fan
I've heard that if an auto tranny has been ignored long enough for the fluid to get discolored, you're better off just leaving it alone. If you change it, the fresh fluid will probably end up flushing something loose & killing the tranny.
I've tried both ends of this theory myself & currently have a '91 Exploder with 245K on the clock, nasty looking fluid, leaks ever so slightly, but shifts great! I'm scared to change it.
