Page 1 of 2

New kid sayin' Hi

Posted: January 19, 2008, 11:05 pm
by TheTruant
Hi everybody, name's Dan, I'm 19 and live in Fredericksburg Virginia. Traded another car I had for a '66 F-250 last fall. Lurked around the site for awhile and thought I'd say hi and show you all some pictures of my truck and what I've done to it. Guess that's about all...hope you don't have dial up :oops:


Here's the motor as I got it. It runs GREAT. After running the numbers it turns out it's a '65 390ci block with '67 Mustang GT cylinder heads and intake. Hooked up some extra gauges under the dash...it runs 80psi of oil pressure on start up and is running 60psi going down the road most of the time

Not to mention that when I stuck the bore scope in one of the cylinders it was clean enough to read .030 over on the top of the piston...hehe...it's a fun truck for sure...sounds good at about 4,000rpm through those worn out glasspacks. :twisted:



Image

Image


Polished and painted valve cover...little nicer than the old one

Image


And my motor and engine bay all painted and put back together. Also re-wired my igniton after having some trouble with later on.

Image

Image


Next issue was the Dodge wheels :shock: :shock: :shock:

Image


Cut out some diamond plate and stuck it on the hubcaps...what Dodge? :lol:

Image

Image

Muuuuuch better!

Image


Put a cheap Autozne seat cover on it for a few weeks but annoyed the hell out of me being loose all the time. So I ordered a replacement seat cover from LMC and put it on.

Image


What was underneath.

Image


Finished product...all the wrinkles and wavy spots are out now that it's been used a bit.

Image

After all that stuff was done I went about making a center console to hold a radio and a couple cup holders.


Paper mock-up


Image

Front half layed out...

Image

Everything cut out...

Image

Also made a little lift out compartment for misc. crap to go in. Made it out of one piece (except the divider).

Image

Here's the fron half done. Lift out compartment is on the left (duh)

Image

Back half bent up and welded on..

Image

Cut out my CD player holder and tacked that in and also added some covers on the side (you'll see why later).

Image

Here it is after getting painted and wired...

Image

And here it is all done and installed

Image

Those covers were for a pair of LED strips I had laying around...stuck them on the side and wired them up to a switch. Gives the floor a red glow at night time, looks really cool.

Image[/B]

You can also see the 12V outlet I put in and the covered switched which runs a pair of back up lights/tailgate eliminators that I cut into the rear bumper...

Image

And here she is a couple days ago after a trip to the car wash.

Image

Image

Image

Image

Posted: January 19, 2008, 11:11 pm
by TheTruant
Oh yeah, also fixed a bunch of bad wiring, put on the missing emblems, undercoated the inside of the cab, etc. whistle.gif

Posted: January 19, 2008, 11:39 pm
by FORDMANLCRACKEL
:welcome: Dan, Looks like a nice truck. You been busy. welcome.gif

Lonnie

Posted: January 19, 2008, 11:46 pm
by castruck_1964
:welcome: Dan nice looking truck and keep up the good work :D

Posted: January 19, 2008, 11:55 pm
by Slick Fan
Welcome aboard! welcome.gif
Nice looking truck, you've been doing great looking improvements on it. :D

Posted: January 20, 2008, 12:24 am
by TheTruant
Thanks fellas wave.gif

About all I have left to do is re-skin that rusty tailgate and finish cleaning up some of the wiring. Got new brakes to put on it one of these days as well.

Posted: January 20, 2008, 1:28 am
by Greg D
:welcome: Dan, you have a real good start going there!

Posted: January 20, 2008, 6:11 am
by GLindley
welcome.gif Good job Dan! I like the colors of your tu-tone! Sharp looking truck!

Posted: January 20, 2008, 7:46 am
by 66fordtrucknut
Welcome to the club from Md. Eastern Shore, Great job, looks like your a fabricator which is what I've done for 30 yrs. Truck looks great!
Charlie

Posted: January 20, 2008, 10:39 am
by ICEMAN6166
welcome.
looks like you have done a great job so far on the truck.
:thumright: :thumright:

Posted: January 20, 2008, 10:53 am
by Johnny Canuck
Hey looks great! Welcome to the club!! :welcome:

Posted: January 20, 2008, 10:59 am
by Fanatic
Welcome aboard!

Even with dial-up it was worth the wait.

Tim

Posted: January 20, 2008, 11:59 am
by Hoofbeat Racer
Welcome to the club. Thanks for all the great pictures! As you can tell we rely on other people's progress to help motivate ourselves :lol:

Keep up the good work!

Posted: January 20, 2008, 12:56 pm
by PFM-64f100
:welcome: Very cool pictures I do like that console with the radio in it. it is better than cutting up the dash to install a radio. Keep up the good work.

Posted: January 20, 2008, 1:25 pm
by TheTruant
PFM-64f100 wrote::welcome: Very cool pictures I do like that console with the radio in it. it is better than cutting up the dash to install a radio. Keep up the good work.
Yep, I was really againist cutting up the dash.


Thanks everbody! :D

Posted: January 20, 2008, 1:48 pm
by f100matt
:welcome: Great lookin truck

Posted: January 20, 2008, 3:45 pm
by MrEvil
Dan that's one heck of a truck you got there. And that's some darn fine fab work you did on that center console. I must say I'm jealous.

And kudos for getting rid of the anatomical cross-sections on your centercaps. The Diamond plate looks good.

Posted: January 20, 2008, 8:55 pm
by samdog66
OUTSTANDING!

Posted: January 21, 2008, 7:00 am
by jwh f-100
Welcome!!! Nice truck!!
Looks like the one a PA member here was selling. Good to see a slick going to a good home. You'll see it in the "Trucks for sale" section. Glad to see it brought us a new member.
Keep up the good work.
Jason

Posted: January 21, 2008, 2:17 pm
by Slick Fan
jwh f-100 wrote:Welcome!!! Nice truck!!
Looks like the one a PA member here was selling. Good to see a slick going to a good home. You'll see it in the "Trucks for sale" section.
Man, I knew I'd seen that truck somewhere, just couldn't remember where. :D

http://fordtruk.com/forums/viewtopic.php?t=2599