Page 1 of 1

68 Fairlane cowl repair. Pix!

Posted: March 2, 2008, 10:08 pm
by Phil
Johnny banged this out today with my POS $50 Sears welder:
I was pretty much a tool caddy. Did a little welding and prepped parts as he stuck em on.

Image

Image

Image

Image

Image

Kid drilled holes in stuff

Image

Image

Posted: March 2, 2008, 10:46 pm
by 36truck
Looks much better now Phil.

Posted: March 2, 2008, 10:59 pm
by Greg D
That looks good!

Posted: March 3, 2008, 1:15 am
by blackagatha
I just remembered a question i had, how did you remove the slat panel, cut it or unscrew or what?

Posted: March 3, 2008, 7:01 am
by Phil
blackagatha wrote:I just remembered a question i had, how did you remove the slat panel, cut it or unscrew or what?
Not sure what you mean by "slat panel"

If you mean the whole assembly we cut out the OEM with a cutoff wheeel then ground all the spotwelds of the remaining pieces


Did the same with the donor part.

We then drilled holesin the donor part where the spotwelds were
and tacked it all together. Alon the front we were going to but weld the firewall to the nub I left but we ended up lapping it to hide some voids. Seam sealer will cover anything you see and keeep the H2o out but to be honest, you can't see anything at all. John was dissapointed with the welds and the look but I couldn't be happier. Its as good as factory all over.
I have another post showing removal in this section someplace

Posted: March 3, 2008, 9:14 am
by Johnny Canuck
I am in awe.

This is so far away from any skills that I have, it might as well be on mars

One question Phil, why didn't you soak down the rusty kick panels etc with Ospho while you had it apart?

Posted: March 3, 2008, 9:28 am
by Phil
Johnny Canuck wrote:I am in awe.

This is so far away from any skills that I have, it might as well be on mars

One question Phil, why didn't you soak down the rusty kick panels etc with Ospho while you had it apart?
I know I know, I should have but I have been on a scheule and John is only available on Sundays. He missed last week cause I didn't get the cowl stripped and he was sick. Had I missed this Sunday it would have just gotten worse timewise. I need to roll the car around the garage and I wasn't about to move it all hacked up.

On top of time constraints I plan on POR 15ing stuff and that crap doesn't ever stick to clean metal for me, all that rusty stuff is surface.
I am on the fence though about POR, I may Blu lighning it all clean and use my siphon fed POS gun and etch or epoxy prime everything. John said I should have dipped and E-coated it.

I am making this up as I go along and probably skipping important steps but in the end I am building a driver. I'll never do another resto. The cars are just too scary to use. When they are that nice they keep me awake at night.

Also this car, while I like it, its just an impediment to getting to my Unibody :twisted:

Posted: March 3, 2008, 12:51 pm
by Slick Fan
Looks pretty darn good, your friend sure makes it look simple. :thumright:

Re: 68 Fairlane cowl repair. Pix!

Posted: March 3, 2008, 1:13 pm
by GLindley
Heavyhauler wrote:
Kid drilled holes in stuff

Image
Hey Phil, how quickly did he learn to be careful when the bit is breaking through that it "catches" and breaks your wrist?!?

Posted: March 3, 2008, 1:20 pm
by Phil
Brand new sharp bits + redwood. Even a 6yr old can do it

Posted: March 3, 2008, 1:23 pm
by GLindley
I guess if I was more observant, I'd a noticed the Sawdust and not metal chips!
Being more observant, it's a character flaw of mine, just ask the wife!

Posted: March 3, 2008, 3:41 pm
by ICEMAN6166
Bodywork is not my strong suit either. glad most of my patches are covered by the floor mats. will never have a show car or truck that i did the bodywork on but i am more interested in driving them than worrying about scratches.
looks real good Phil.