Page 1 of 1

International tractor

Posted: March 18, 2008, 7:57 pm
by Paul Merrell
Does anyone know how the transmission on a IH 2500 with a diesel engine with hydro drive work. The tractor won't go forward or reverse. We have a manual but we do not know what is wrong with the tractor and the manual is very confusing with other tractor series in the same manual.

Posted: March 19, 2008, 12:53 am
by Ford4jack
Paul here's a few thoughts

Check the oil level & check the filter.

Check and see if the speed / directional control linkage is turning the shaft for the control cam.
This should be located on the top of the transmission case under the sheet metal guard.

If your unable to get a hydrostatic growl out of the machine the coupler plate from the engine to the shaft might have stripped.

If it has the growl but does not try to move or moves slowly a valve might have stuck or a pressure tube etc might have failed. A quick check would be to start with the machine cold and feel around for hot spots at any valves or tubes you can reach. Feel around the case also. Bypassing oil shows up as heat quickly.

Check the sump oil for heat and foam also.

There should be a place to check the system pressure lube pressure etc a local dealer should be able to tell you where the test points are and the pressure specs.

Just a thought or two from a 2400-A owner
I'm sure there's many other things it could be never been into a IH hydro myself.

Dealers are usually very helpful in helping you troubleshoot a machine.
As my former boss used to say we sell parts also.

Good luck with it hopefully its just a small problem.

Posted: March 19, 2008, 10:28 am
by Ford4jack
Paul I figured I would try to explain how the hydrostatic system works.
Its all rainy here and I need to practice writing and me grammar anyway.

Basically its two pumps with a ring of pistons in them. One is a pump one is a motor.
One just pumps high pressure oil to the other thru a manifold between the two.

The displacement of oil is controlled by how far the pistons move. The piston movement it controlled by a servo with a plate that rides against the pistons.

The servos are set to be in a center position in neutral. When the pump servo pivots forward the motor servo pivots back
oil will transfer thru ports in a manifold between the pump and motor and it goes in one direction. Reverse the servo direction and it goes in an opposite direction. The servos need to be in time with each other.
The manifold has forward / reverse ports in it

The power from the engine is thru a shaft that powers a charge pump to give the system oil to work.
This shaft is also connected to the hydro pump.
A second shaft is connected to the hydro motor to power whatever its connected to.

The control petals or lever to operate the tractor work a valve that controls how much and what direction
the servos move.


I looked in my 2400-A parts book and noticed they listed a petal or a lever control on these.
The petal one works a cam style control for the control valve and the lever one has a valve control.

I would almost bet money the 2500 is set up the same as a 2400 that's what I like about IH they seem to stick to one design.

I also noticed they have a inching petal system. One more thing to check.

A couple of other thoughts are if you change the filter see if there's any rubber debris in there.
O ring chunks etc and cut open or wash out the filter

Watch for fine bits of cast iron or brass they are not a good sign.
The hydro system has to be perfectly clean or the plates that go on each end of the pump / motor will wear and the pressure will fall heat will build etc.

One more thought check and see if the PTO works it should be powered by the hydro motor shaft.
This should let you know if its getting power thru from the engine.

Again good luck on it

Posted: March 19, 2008, 12:56 pm
by Paul Merrell
Ford4jack thanks for your response it does growl when put into gear but we took a cover off and looked in the trans when running in reverse the level of the fluid stays level but when put in forward the level of the oil raises very fast and overflows! We have changed the filters and oil and found one check valve bad and replaced that also have installed new seals in both servos. I don't know about the pto but the backhoe on the rear works. We bought this tractor this way we payed $3000.00 if we could fix it we could have a ok tractor.

Posted: March 19, 2008, 4:14 pm
by Ford4jack
Paul
Looks like if the backhoe's working the power flow from the engine is getting thru to the hydraulic pump.

You might check the center section housing or what I call the manifold the pump and motor for a crack.
These things can run very high pressure and a crack in an housing or piston will leak fast

It looks like the fwd & rev relief valves are located in the center section housing along with the directional shuttle valve.
Might have just washed out a O ring and backup ring off a relief valve.

Should be able to test this with compressed air thru a feed port.
Might try pulling the innards out of the shuttle valve and work the spool by hand to flow air to the relief's.

If you get a bunch of air coming out and cant tell where from just fill the test section with oil and look for a
gush of oil when you hit it with air again.

I would be tempted to drop the oil and scour the sump with a magnet and rag to see if there's any clues there also. Not sure where the manifold sets in relation to the oil level so this might make leak hunting easier also.

Or if its down in the oil it might be easier to look for air bubbles when pressure testing.

Hope this helps you find the problem.

Posted: March 19, 2008, 7:35 pm
by Paul Merrell
Well we did remove the bottom cover when we had the top cover off because we thought there was a bushing missing for the shift cam on the top cover did not find any metal. When we run it it seems to take the oil from the rear housing under the seat and dump it all into the front section thats in front of the seat. We do not know of any dealers that know anything about this tractor. It seems that IH was bought out buy Dresser and then Dresser was bought buy Komotsue. But we got the servo rebuild kits from Case. Do you know of a dealer that has worked on one before.

Posted: March 20, 2008, 8:54 am
by Ford4jack
Paul the dealer in Lexington TN might know about them.
There a case / ford dealer

They had a 2400 on the back lot that they used around the shop but I think they parked it because they got tired of spending time and money on it.

Any older dealership should have the tools and knowledge to repair these.
I believe what you will run into is the dealerships know that a repair bill on one of these can easily go over the value of the tractor so they have a tendency to shy away from them.

You might find a retired IH mechanic willing to work on it Or try a dealer during the winter season when work is slow.

I do believe the best route to take would be to troubleshoot it yourself.
If its something simple cool if its an expensive repair you will come closer to getting your money out of it just selling it to someone as a parts or project tractor.

Might consider used parts if it needs something pricey though that is a spooky thing to do on a hydro unit.

I have an 10 year old parts connection book that lists dealers and yards that carry used parts.
There might be an online version of this now.
If your interested in trying used parts let me know and I will scour thru it and see if there's anybody close that you could check with.

To bad we don't live closer to each other you got my curiosity up on this problem.

I noticed on ebay there's a factory hydrostatic repair manual for the 2400-3500 tractors.
Just punch in ih 2500 and its in the store listings under the auctions page.

Know you have a manual but if its not a factory manual the info you need is spotty at best.

Well once again hope its something simple and good luck on it.

Posted: March 20, 2008, 5:59 pm
by Paul Merrell
We have a parts manual and the shop manual we are going to do some pressure testing Friday and Saturday. I have a borescope and a mirror I hope to find the leak.

Posted: March 21, 2008, 12:48 am
by Ford4jack
Cool deal Paul I'm sure you will find it and hopefully it will be something that you can get to without gutting the tractor.
I need to work on our tractor its weak as tea and the pto has been acting up.
Maybe I will just get a herd of goats to bush hog with. :lol: