Page 1 of 1

This Model A is incredible!!!!!!!!!!

Posted: March 26, 2008, 7:28 pm
by Greg D
Custom built/restored for a Rally Driver to appear as stock as possible. There is even a switch to make it run rough so it can sound like a stock A! There are 200 incredible pics in the second link of it's restoration.

http://www.youtube.com/watch?v=iFSGSL3Nrmc

http://www.mat.fi/project1929fordmodel-a.htm

:shock:

Posted: March 26, 2008, 8:13 pm
by MadMaxetc
OMG!!! :)

That is bad ass!

Talk about attention to detail!!

For those with dial up, Skip to pictures 124 139 164 174 178 186 189 199 and 200.

That is VERY well done!

Posted: March 26, 2008, 8:23 pm
by FORDMANLCRACKEL
Those boys are master craftsmen. Love the engine. Its a top of the line sleeper. I dont think they would have a bit of trouble building a Slick. I enjoyed the vid. the most. :rocker:

Lonnie

Posted: March 26, 2008, 8:41 pm
by Paul Merrell
My Uncle has a Model A but its nothing like that! I would love to drive it one time and smoke some ricer!

Posted: March 26, 2008, 8:43 pm
by MrEvil
Now that is a flipping awesome project. I can only picture the look on some honduh drivers face watches that Model A take off like crap through a tube.

Gives new meaning to the song Hot Rod Lincoln even though the engine isn't a lincoln engine.

Posted: March 26, 2008, 9:13 pm
by Greg D
Paul Merrell wrote:My Uncle has a Model A but its nothing like that! I would love to drive it one time and smoke some ricer!
I found it posted in the Mustang GT registry.
My reply was imagine the look on some ricer kids face when you spank him with it, lol.

Posted: March 26, 2008, 10:49 pm
by Johnny Canuck
That is THE coolest hot rod I have EVER seen. Bar none.

Thanks for that Greg. :thumright:

Posted: March 27, 2008, 1:22 am
by Alan Mclennan
That is one well built A model, the detail is astounding, I`d say this is not their first car and I hope not their last. One thing did strike me as strange was they had racing harnesses but only a timber frame in the body!, still a very nice sleeper 8)


Alan,

Posted: March 27, 2008, 10:09 am
by Garbz
Alan, Thats ironwood ya know....NHRA certified....

Garbz

Posted: March 27, 2008, 3:55 pm
by blackagatha
WHOW.

what IS that engine, does anybody know? DOHC Hemi of sorts, looks like a flathead.... amazing.

Those aluminum "wooden" wheels are a slick concept.

Those harnesses coming out of the rear seat are quite odd. too bad it doesnt have 4 harnesses coming out of a more rational location.

Also, we were discussing "pull off angle" of seatbelts in my crash worthiness design class. A "pull off angle" such as that would crush the hell out of the spine. The ideal angle is actually vertical (90 degrees) to 80 degrees back. 30 deg. is liable to crush spine. That Thing had an angle of like negative 50... you get into a situation that a harness like that would normally help, and you'd wind up wishing you had left the car with no belts at all...
Especially with those ultra-low backed seats... might fit properly for a midget...

other than that, I like it...

Posted: March 27, 2008, 4:02 pm
by Greg D

Posted: March 27, 2008, 7:49 pm
by Johnny Canuck
Nere saw the aluminum wood wheels part.. what pic is that?

Posted: March 27, 2008, 8:01 pm
by GLindley
Johnny Canuck wrote:Nere saw the aluminum wood wheels part.. what pic is that?
I didn't wait for all 200 pics to load so I can't say if there is a pic of the rims, but just before the 3 minute mark on the You Tube video, there was a close-up of one of the rims.

Posted: March 27, 2008, 8:41 pm
by Greg D
There are several pics of the process of making the rims, spectacular.

Posted: March 28, 2008, 12:10 am
by blackagatha
Johnny Canuck wrote:Nere saw the aluminum wood wheels part.. what pic is that?
I think pic 120 or so was the beginning of the seg on wheels.