Page 1 of 1

not mine, not slick, not even ford....

Posted: March 28, 2008, 1:11 am
by blackagatha
but this is what's been keepin me busy on all my breaks. My cousin's '39 "BRAND X".... haha eh, I think it's old enough to pass under my brand scrutiny... hahaha

Image
final ride height after the axle swap

Image
overall view of swap. The axle was from '78 Malibu wagon. I should have taken a pic of IT. that thing is wasted.... hahaha!

Image
upper link mounts (I put a gusset between the tabs), the pipe is welded to the frame, then a split-box gusset was added. I will probably close the box at a later date

Image
The lower brackets from over axle

Image
Spring perches, top is galv. pipe, channel and rusty water pipe. Bottom is original lower perch that was cut off axle due to conflicts. pipe has big gussets to bottom and sides of frame, inside.

Image
Trust me, it LOOKS a LOT more dangerous than it actually was... The 2 Hi Lift Jacks alone would have been terrifying, but we had 2 rachet straps stabilizing it... one was attached to the 3000 pound generator, the other to a sway bar hung over a wall as an anchor. it was rock solid....

Image
His 383 we put in during xmas break. Also the steering rack we had to relocate. That was a BIG project in itself. The engine balancer and rack wouldn't coexist in the location of existing eng mounts, so we moved rack about 8 inches forward with BIG bolts, cost $10 each, and chunks of pipe, and big gussets and plates. it looks really cool. I wish I had more pics...

Image

Image




We gotta get some brakes, a steering column, a radiator, and some hunk of crap to serve as a shifter and he'll be able to drive the thing around... it's getting close...

The whole axle project cost zero in parts, but $60 for gas for the damned generator that doesnt like to run. He doesnt have a 220 plug though. Sadly the truck is at his house. My garage has a nice clean, reliable 220 outlet, and a concrete floor, and a roof and a door.... man it would be nice to be able to work in there...... When we get the thing drivable maybe we start doing work at my place... trouble is ALL the REAL work is gonna have to go down/HAS already gone down at his place... what a pain!

Posted: March 28, 2008, 1:26 am
by blackagatha
Image
it was actually intact at this point. We had just dragged it out from under the car. Now the chassis is no more than knocking, probably locked up engine and front suspension, and "wheelbarrow" handles on the back, I actually cut all the axle framework out with a grinder before I realized I was bein a retard and that I should just fab new...

Image
by far the most hazardous thing I have ever done... precariously perched on a stack of cinderblocks to the edge of the spare tire well, and a single 2x4 up front.... while we were dragging the chassis out from under... When we tried to let it down, the 2x4 snapped and car did a big belly flop in the dirt...

And yeah, I know. It was the WRONG car to get as a donor, but it's too late now... It's a "perfect" -sheetmetal anyways- car that had a crap knocking 305.... Sadly it wasnt something cool with a fresh 350 that was wrecked.... whatever. He needs to sell the front doghouse and whatever he can on craigslist to recoup some of his cost... Anybody interested?

Posted: March 28, 2008, 5:53 am
by Ford4jack
Looking good there BA.
Its motivating to see y'all building what your cousin wants with what y'all got.
There's a lot of folks that just never get a project going because conditions are not perfect to work on it or a kit is not available for what they want to do.

Posted: March 28, 2008, 7:58 am
by frank66
Looks good. Too bad we're not closer, my friend's malibu is in desperate need of floors.

Posted: March 28, 2008, 8:23 am
by Johnny Canuck
Looks like something in which that engine belongs.
A fairly solid truck to start with, should be an alright project once she hits the road!

Is that gonna be a heated tailgate? :lol:

Posted: March 28, 2008, 3:11 pm
by blackagatha
frank66 wrote:Looks good. Too bad we're not closer, my friend's malibu is in desperate need of floors.
That really IS unfortunate. If he can find a way to get it, im sure he can have the whole carcass for cheap. We may see how much it would cost to send the floor pans... Any smaller parts that he wants? A lot of stuff has been cannibalized for the truck, but you know...
Looks like something in which that engine belongs.
A fairly solid truck to start with, should be an alright project once she hits the road!

Is that gonna be a heated tailgate?
YES.finally somebody got it right. SBC goes in a chevy. SBF goes in a FORD... in Jeebus's name we say, AMEN!

Yeah, the truck really does seem pretty solid. The original frame is a wee bit thin in spots, but I think it will be ok. The PO Bolted steel straps to the top and bottom frame rails to try to make it stouter. I welded them down and removed most of the bolts. PO also boxed in the frame up front when they put in the mustang 2 front end, seems decent.
It's funny though, they did a lot of stuff without considering the ramifications.... Like the fact that the truck at one point previously had a SBC and a 4speed, and was a driving unit. Then whoever had it gutted it out and sold it to the most recent PO, who likely put in the M2 front clip. They didnt consider the fact that a SBC would NOT fit with the steering rack.
Looking good there BA.
Its motivating to see y'all building what your cousin wants with what y'all got.
There's a lot of folks that just never get a project going because conditions are not perfect to work on it or a kit is not available for what they want to do.
It really makes me happy to be able to help the kid. And it makes me happy that he's into this. The project has created a LOT of bonding time that I would have never gotten otherwise.

And conditions are FAR from ideal. The kid's flat broke, and his dad took off 10 years ago ripped on prescription drugs, and stole a bunch of money, and hasnt paid much more than a dime in child support. Fact is, I'm glad he's gone, just sucks that he's such a deadbeat. If HE was helping build the truck, it would become a hell-heap like every other project he ever did.

Most kids would find all that to be a stone wall precluding any chance of something cool. Sadly, the kid has WAY too many commitments right now. He's in ROTC AND Cheerleading... CHEERLEADING??!!!?! yeah. he accidentally got himself recruited, with no option. He did a backflip or something in front of the coach and he was caught.
Image
Image
Image


anyway, commitments--- he doesnt have time to make money OR do simple stuff on his truck, so every time I come home I help him out, nothing has been done, and he's still on a zero budget. just happens that he gets his school breaks about the same time I do, so I can help. It's a Little disheartening that he doesnt do anything in between, but I know why, so its ok.

Posted: March 28, 2008, 3:35 pm
by Greg D
Definitely a cool project. Keep us updated.

Posted: March 28, 2008, 3:49 pm
by jakdad
Be a great truck to put a Cleveland in with a built C-4 and 9".

Posted: March 28, 2008, 5:29 pm
by Phil
Rodding at its finest

I have that same T/A shirt :lol:

Posted: March 28, 2008, 5:36 pm
by blackagatha
the bloody hell just happened? I was typing a reply here and the page disappeared and went to the PM page... Probably due to my damned touchpad on the laptop. it pisses me off. every time i accidentally touch it with my hand it clicks somewhere and makes weird things happen.


Anyway, I was sayin that I have definitely thought about a 351C or the such, but you know how it is... And we wanted to put in a Ford9" axle, but he HAD the 10 bolt, so we might as well use it... I figure when he makes the 10 bolt go off like a bomb with the 383 (a bit of a step up in power from the old 305) we'll get a 9" lined up for him and fabricate on some tabs to utilize the 4 link we just put in. OR if he comes across some cash, grind it all out and start from scratch with a custom-cool setup.

At this point, I'm gonna basically guarantee that the turbo 350 trans is going out within the first week he's drivin it, especially if he decides to have ANY fun at all. It drove ok I guess, though I never rode in the wagon, but when we took off the pan, there was huge chunks of friction material in the bottom. Tranny shop dude said they're notoriously filthy trannies, and it'll probably be ok at least for a while.


OH YEAH, I meant to ask what JC meant by heated tailgate in previous post... you talkin about those goofy reflectors, or the goofy "toaster filament" painted on?






oh yeah, and if anybody here has any ideas:
We got the engine running at the end of xmas break, and he and my uncle messed with it some more, but he cant get it to idle. I still need to have a look at it, and get a cooling system installed, but it runs like a striped ass ape, but craps out when you quit jimmying the throttle.

haha oh yeah, I think right before that photo was taken, we were trying to get it started, and it blasted out a BIG backfire straight up in my face... well, I was back a little way, but not far enough!!! I was ringing for like 5 minutes after that....
Hell, you be ringing after hearing the exhaust, The guy that sold us the engine said it's got about 10.5-11.5 compression... {{yea I know, vagaries and engines dont mix, but it seems ok. I guess he was a middle man from some other dude that built it. He flipped out when we told him we pulled the pan and main bearings when we were having big problem, and found out that the old bearings (worn clear thru the bronze) were still in there, and that there seemed to be a slight bend to the crank... He took it back and took it to his own machine shop, supposedly put in new bearings and got crank trued at no cost to us, so that was cool. Cam and timing set are not new, but seem to be within tolerances... I would have rather seen him do like I did with my engine, have professional machine work done, then personally (and Cleanly) assemble a "brand new engine" with fresh parts, etc, but that cost me about $4-5000.... He paid $750. }}

anyways, high compression, and 3" pipes under the running boards, with glass packs. He's gonna piss off the neighbors (and cops!) I actually only ever ecperienced it from being crouched over the engine. It sounds REALLY SWEET from up front. I have a feeling the back will be "BLINDING WITH SOUND"!!!


oh yeah I also wanted to post this
Image
granted it's sky-jacked in the rear with no axle, but just overview of the truck...

Posted: March 28, 2008, 8:41 pm
by frank66
That truck is going to look great. I love trucks of that era. My dad had this one for a while. The side pipes were loud enough to drown out the scraping over speed bumps.

[albumimg]3324[/albumimg]

Posted: March 28, 2008, 9:23 pm
by Fanatic
I only have one word
"SCARY"


will you guys PLEASE be careful!

Posted: April 1, 2008, 12:20 am
by blackagatha
Fanatic wrote:I only have one word
"SCARY"


will you guys PLEASE be careful!

UH YEAH.... I agree entirely. That thing is gonna be a lean mean Rat Trap... Sprung to kill without the slightest hesitation...

With the power the engine is thumping out (unknown really, but I can feel the power in me), the rear end of that thing is gonna have a hard time staying on the ground, except on perfect pavement conditions. I'm REALLY glad it has updated suspension in it, if not it would have likely been a deathtrap...

Posted: April 1, 2008, 8:37 am
by Johnny Canuck
OH YEAH, I meant to ask what JC meant by heated tailgate in previous post... you talkin about those goofy reflectors, or the goofy "toaster filament" painted on?

since the invention of the SBC, Chev trucks have always had the optional heated tailgate.
Keeps your hands warm when you are pushing them.
:wink:

Posted: April 1, 2008, 12:54 pm
by Slick Fan
blackagatha wrote:
Fanatic wrote:I only have one word
"SCARY"


will you guys PLEASE be careful!

UH YEAH.... I agree entirely. That thing is gonna be a lean mean Rat Trap... Sprung to kill without the slightest hesitation...

With the power the engine is thumping out (unknown really, but I can feel the power in me), the rear end of that thing is gonna have a hard time staying on the ground, except on perfect pavement conditions. I'm REALLY glad it has updated suspension in it, if not it would have likely been a deathtrap...
I think Fanatic probably meant be careul & don't let that truck fall off that precarious perch & squash your azz. :twisted:
Looks dangerous as hell to me, even if you do have tie-downs holding it to something, just be careful...or at least stick someting under there to catch it, if it does fall.

Beyond that though, it looks like a fun play toy. :)

Posted: April 1, 2008, 1:30 pm
by 36truck
Jc that truck came out before the sbc so no heated tailgate on that one.

Posted: April 1, 2008, 2:20 pm
by Johnny Canuck
LOL it'll be an add-on like seatbelts

Posted: April 1, 2008, 9:56 pm
by blackagatha
well, sure there was a slight possibility of something bad happening when the truck was up in the air. But i'll put it out there that it was solid as a rock compared to that car.... jeezis. #1, I cant believe I did that, #2, it's amazing that it didnt kill us. and we were basically under the damn thing wrestling the chassis out from under.... WTF were we thinkin man?!?!?!


hahah I like this hand warmer tailgate concept.... sounds like a customcab-style add on.


And I think installing some seatbelts will likely be the most difficult project- there's not really much good to secure a shoulder belt to.... Unlike the slicks, there is no windowframe to speak of to butt a backing plate into, and the wall goes clear to the roof, and SO wide from window to door... The only thing that I would trust would be a roll bar of some sort installed behind the wall, to try to retain a clean look.