Page 1 of 1
Disc Brake Job /Added New Photos of Frontend
Posted: June 1, 2008, 4:09 pm
by 52elwood
Hello Alll
My Disc Brake job is almost done but, NAPA gave me the wrong Tie rod end so will have to complete next weekend but here's what it looks like so far.

Thanks to all, for your help on this project.
Richard
Posted: June 1, 2008, 5:00 pm
by Gritsngumbo
Looks great! Plus you get an A for neatness.
Posted: June 1, 2008, 5:00 pm
by ras4434
OMG, that is almost as pretty as my son right after he was born. Well maybe not right after. GREAT job. Were those parts cleaned up or are they new? I will save the pics to use when I get confused when I do my conversion. Again great job and thanks for the pictures.
Posted: June 1, 2008, 6:36 pm
by Alan Mclennan
Richard , nice work mate! brings back memories but with out grease dirt and tools everywhere

. I noticed your radius arms are made of pressed steel where as mine are cast iron are they after market or original

nice pic`s too!
Alan,
Posted: June 1, 2008, 8:33 pm
by 52elwood
Hey,
Just a replay to Ras4432 & Alan.
The parts are from a 77 f150 I took every thing for the front end and pressured washed the axle, radius arms & spindles and then I wired brushed everything to get the rust and dirt off that didn't come off with the pressure washer. Then before the install I painted every thing with Hammer paint from Home depot. I used the springs from my 66 and then replaced the rotors, calipers, bearings, seals, pads drag link, tie rod ends and bushings that I brought from NAPA. Just follow the Technical form for the Disc Brake swap and every thing works great. I had now problems. The 66 had kingpin problems and the 77 had been replace only a few years back. I will keep the old 66 front end in case someone needs parts.
Richard

Posted: June 1, 2008, 9:40 pm
by Greg D
Damn!
That looks nice !
Posted: June 1, 2008, 11:23 pm
by blackagatha
I wish my front end looked that nice! but alas, when I installed my front disks on the straight axle, I was in a pinch for time and didnt even rightfully clean the axle! I just scraped the crap back from the spindle for the install...
SOME DAY it will be all shiny and Ford Red... Some Day....
and I wish my brakes didnt use those stupid C#@^Y calipers!!! I like your ford ones much better... and they actually have backing plates!
Posted: June 2, 2008, 5:33 am
by DV65CustomCab
Wow. Painting the parts before installing them...

Not how I roll, but that looks awfully nice.
Posted: June 2, 2008, 4:04 pm
by Slick Fan
That's about how the front end on my '66 looked...a looong time ago.
I like the paint color on yours, looks great!

Wow..looks nice!!
Posted: June 2, 2008, 10:48 pm
by winr
Hey Richard...nice job!!!
I am almost through with my disks.
I only painted a bit of the axle also....
http://s153.photobucket.com/albums/s201 ... I_1116.flv
Richard.
Posted: June 2, 2008, 11:42 pm
by MadMaxetc
Alan Mclennan wrote:Richard , nice work mate! brings back memories but with out grease dirt and tools everywhere

. I noticed your radius arms are made of pressed steel where as mine are cast iron are they after market or original

nice pic`s too!
Alan,
They switched to stamped some time in the late 70's Might be 76, but not sure.
Good looking job so far!
Posted: June 3, 2008, 5:01 pm
by Alan Mclennan
MadMaxetc wrote:Alan Mclennan wrote:Richard , nice work mate! brings back memories but with out grease dirt and tools everywhere

. I noticed your radius arms are made of pressed steel where as mine are cast iron are they after market or original

nice pic`s too!
Alan,
They switched to stamped some time in the late 70's Might be 76, but not sure.
Good looking job so far!
Thanks for the info Dan,
Alan,
Posted: June 3, 2008, 9:25 pm
by 52elwood
Hey everyone,
Thanks for all replays. I just picked up the rest of the parts from NAPA, hope
to complete the job this weekend.
I'll post new photos then.
Richard
More Photo's of this weekend
Posted: June 8, 2008, 7:35 pm
by 52elwood
Ok,
Here it is.
Completed the front end install Shocks, Steering box, Adj. Front end and Painted the Cab bottom, Installed new Cab Rubbers. Painted front of Cab.
A lot of work and it was Hot.('

')
See you next week end.
Richard

Posted: June 8, 2008, 8:48 pm
by helicorbin
wow, 52elwood ........you sir are a role model, good attention to detail, hooahh