Page 1 of 1
Sell or Scrap?
Posted: September 13, 2008, 7:34 pm
by ABA
I got a 4barrel intake for a FE block, yes a cast iron one.
I was going to use it but have since changed my mind.
Should I sale it or scrap it?
I got a c6 tranny off a 460 that has been setting up so it's only good for a core and I got a 8.5 pumpkin off a T-Bird that I doubt I will ever need that I am seriously considering selling for scrap.
The intake would add another 80lbs.
Anyone here interested in the intake let me know. I'll let it go cheap.
It's all cleaned up and painted and ready to install.
Posted: September 13, 2008, 7:59 pm
by FORDBOYpete
ABA,
Post the number on intake for us so we know what it is.
THANX
FBp 
Posted: September 14, 2008, 6:38 am
by ABA
I took it off a 352 in a '65 Galaxy.
I got the chrome valve covers too but I'm keeping them.
I'll have the # in a few.
Posted: September 14, 2008, 7:18 am
by DV65CustomCab
I'd take it, but the shipping wouldn't be worth it.
I see them on Ebay pretty frequently (intakes) and they rarely get bids. Not exactly rare I guess. But, they do flow very well. No reason to go aluminum unless weight is a concern, and on these trucks, it ain't!

Posted: September 14, 2008, 9:44 am
by shawns fords
I have two of them sitting here myself a 65 and a 68 intake, nobody wants either one. I am not going to scrap them out the 68 intake is off a S code mustang (mine) and the older one I cant even remember where I ended up with it but It is taller than the later one by a good inch and a half. they are not worth a fortune but should be saved for someone doing a restoration with the specific intake needed
I could use that C6 tranny
Posted: September 14, 2008, 9:54 am
by ABA
You're welcome to the tranny Shawn. It was good when I pulled it. It's just been on the ground for over a year now. It was in my '69 LB. I parted it out and the trans is all I got left.
# on the intake is:
C5AES425C
The S may be an 8. Depends on how the light hits it.
Posted: September 14, 2008, 10:04 am
by shawns fords
I am sure shipping would be a killer on me for tha trans, thanks for the offer. unless you plan to bring it to slick stock 2010 lol I am sure someone down there could use it for something
I dont have a reference to that intake in my interchange catalog but it looks like its a C5AE-9425-C which I believe is a 4 bbl intake from a car probably a T bird or Fairlane I would have to look around for my other identification book to see if I can figure it out, I also think it is probably the same intake I have downstairs lol
I am sure FBP or someone else already knows
Posted: September 14, 2008, 10:12 am
by Greg D
Just out of curiosity, you keeping the 2 bbl or ditching the FE?
Posted: September 14, 2008, 10:21 am
by ABA
Keeping the 2 bbl.
Back when I was looking for power steering parts I grabbed this intake, valve covers, power steering brackets off a ;65 Galaxy at the salvage yard.
Gas prices being what they are and my driving being what it is I know if I got a 4 bbl I'm going to use it so it's in my budgets best interest not to install this intake.

Posted: September 14, 2008, 10:34 am
by 66 POJ
I've got two 2 barrell intakes

Guess they will be door props or counterweights for something.
Posted: September 17, 2008, 11:41 am
by dotcentral
You could always post them for sale on craigslist. That is where I got my cast iron intake.
I just bought a C6 for my 352, supposed to be good, but if it isn't I'll send you a pm about yours.
Posted: September 17, 2008, 6:43 pm
by ABA
Thanks but the C6 I got is for a 429-460, it will not work on our FE blocks.