Thunderboy
Posted: October 3, 2008, 7:20 pm
I can't seem to reply to your message
So here ya go::::::
I put some more pics in my album.
http://fordtruk.com/forums/album.php?user_id=40
My setup is a EEC-V OBD 2. I used this because I picked up a 1996 F 150 that was rolled with 16K miles on it. Got 4R70W trans
I still need to clean up some of the wiring to finish things up but life keeps getting in the way!
Everything is under the hood. I made that aluminum box under the heat sink to hold the computer (weathertight) Updated electrical system with the underhood fuse box from another 90s pick-up. I no longer have any fuses at the headlight switch. Custom made intake tube since trucks use a dual throat throttle body. Lots of hours under the hood with wiring diagrams to run everything. I also installed a full electronic 96 Thunderbird instrument cluster to take advantage of all of the capabilities of this set up.
If I did it again............
.I'd use the EEC-IV system. I had to run from the 104 pin computer for all of the wiring. the EEC-IV uses a 60 pin computer.
I'd use a car intake so that I could find other upgrades if I chose.Actually the truck set up is better but there is little performance upgrades for it.
If I was to stay stock, which I am, I'd choose the truck intake
I'd make or find a fuel tank that would utilize a stock type fuel pump (in tank) just to simplify the fuel system.
I really don't have any regrets on how I did the truck but it was a HUGE learning curve with the Fuel Injection/Computer controls. I have done lots of toying in the past but always with carbureted engines. I still need to get to a shop that can get into the system and make everything correct or at least check it. Everything seems fine but I'd like to know for sure. I wired in the plug for a scan tool and don't have any bad codes coming up.
I'll be glad to answer any questions that I can or show you what I did!
I have abit of pretty good write ups for doing the EEC-IV system.
Tim direct e-mail fnatic1543@aol.com
So here ya go::::::
I put some more pics in my album.
http://fordtruk.com/forums/album.php?user_id=40
My setup is a EEC-V OBD 2. I used this because I picked up a 1996 F 150 that was rolled with 16K miles on it. Got 4R70W trans
I still need to clean up some of the wiring to finish things up but life keeps getting in the way!
Everything is under the hood. I made that aluminum box under the heat sink to hold the computer (weathertight) Updated electrical system with the underhood fuse box from another 90s pick-up. I no longer have any fuses at the headlight switch. Custom made intake tube since trucks use a dual throat throttle body. Lots of hours under the hood with wiring diagrams to run everything. I also installed a full electronic 96 Thunderbird instrument cluster to take advantage of all of the capabilities of this set up.
If I did it again............
.I'd use the EEC-IV system. I had to run from the 104 pin computer for all of the wiring. the EEC-IV uses a 60 pin computer.
I'd use a car intake so that I could find other upgrades if I chose.Actually the truck set up is better but there is little performance upgrades for it.
If I was to stay stock, which I am, I'd choose the truck intake
I'd make or find a fuel tank that would utilize a stock type fuel pump (in tank) just to simplify the fuel system.
I really don't have any regrets on how I did the truck but it was a HUGE learning curve with the Fuel Injection/Computer controls. I have done lots of toying in the past but always with carbureted engines. I still need to get to a shop that can get into the system and make everything correct or at least check it. Everything seems fine but I'd like to know for sure. I wired in the plug for a scan tool and don't have any bad codes coming up.
I'll be glad to answer any questions that I can or show you what I did!
I have abit of pretty good write ups for doing the EEC-IV system.
Tim direct e-mail fnatic1543@aol.com