Page 1 of 2

Learning to paint (like it or not)

Posted: March 7, 2009, 9:37 pm
by Phil
So the guy I hired to paint my 68 convertible didn't work out.

I decided that spending another $3000 to finish the rest of the car (he painted the roller 1st) wasn't in my budget so I rebought my materials that he used up and started doing the body work on the easy stuff like i asked him to do last December.
I did this in about 7 hours. The trunk had a dent and one of the fender extensions had a hole busted in the side. I fixed those flaws and epoxy primed today.
He left my parts in bare steel since March 08 so I had to do a LOT of resanding. I'm gonna work from back to front and assemble in that order.

Wish me luck.

PS those doors are going in the dumpster

Since I wasn't really expecting to do this the garage is its usual cesspool disaster.

This is definitely a shining example of how not to do this:

Image

I keep trying to get a shot of this quarter but it just won't do it because of the intensity of the color.
The human eye and hand picks it up though. I am seriously debating taking a (body) hammer to this and using some filler in a few spots. Maybe the trim will help hide the waves. :roll:

Image

I hope to apply my newfound hobby to my slick someday. Ill stick with white though. It hides a LOT

Posted: March 7, 2009, 11:17 pm
by 36truck
Congrats Phil on grabbing the bull by the horns & doing your own body work.
The parts look good in primer. :D

Posted: March 8, 2009, 12:04 am
by Greg D
Yea, don't be hard on yourself - those parts look good. Just remember the key ingredient in body work is patience. Good for you Phil!

Posted: March 8, 2009, 5:35 am
by STOFFER
it's hard to do body work, it's even harder if you rush thru it, just take your time and try some guide coat next time prior to going to color


guide coat is like cheap/old paint that you spray on top of your primer, not enough to color it in but enough so when yoou sand it it highlights the low and high area's

Posted: March 8, 2009, 8:15 am
by Phil
STOFFER wrote:it's hard to do body work, it's even harder if you rush thru it, just take your time and try some guide coat next time prior to going to color


guide coat is like cheap/old paint that you spray on top of your primer, not enough to color it in but enough so when yoou sand it it highlights the low and high area's
I have a surfacer and some guidecoat so I should be able to do it.
The "professional" did the quarters. He also did some work on a front fender that needed the end patched on. It was going great but the body line is pretty much sanded off now. I got a few tips on how to fix this so that's this week's project.

As for patience I used that all up in November when the guy painted a CRX, a Porche and a Corvette while my stuff sat

Posted: March 9, 2009, 6:08 am
by STOFFER
just remember when it's all done and people ask how much it cost that awsome paint job, you can tell 'em you done it your self

Posted: March 9, 2009, 12:19 pm
by Phil
I'm kind of expecting, "hey man who destroyed your car?" :lol: :lol: :lol:

Posted: March 9, 2009, 6:42 pm
by Anthony
hey Phil, you can always answer, nobody I did it all myself... :mrgreen: . Anthony

Posted: March 10, 2009, 12:21 pm
by Slick Fan
That picture looks a hundred times better than my attempts , so you're doing something right. 8)

Posted: March 15, 2009, 9:10 pm
by Phil
One of my cali doors arived from a buddy in Bakersfield. He packed it amazingly well and sent it greyhound. It came a week later. I stripped it and primed it. It was $200 shipped. I saved a buck and bought a driver's side off Ebay for $160 shipped it arrived the same day. The guy just tossed it in a box. No packing material at all. If I ran around it with a hammer and bahed over all the pinchwelds I coud not have messed it up worse. best yet the door latch area I asked specifically about was all cracked and wasted.

I welded in a patch from a donor door and wasted a whole day fixing it.


Pics from today

Image


#0000 steel wool is my friend

Image

This is the extension I fixed with JB weld
The repair is pretty much the area behind the reflector-the ridge running all down the part.
All that was missing except about 1/2 in either direction. Hard to explain and best of all hard to see.
You can see I didn't fix the strip at the bottom. Too brittle

Image

Bad door, bad repair

Image


good door

Image :shock:

Posted: March 15, 2009, 9:19 pm
by Greg D
Looking good Phil, I have a hint you may like for the thin spot. I'll PM it after I get home so I can give you the right info.

Posted: March 15, 2009, 11:33 pm
by DCarr
Nice work,Phil. Hope my first attempt looks that good.

Posted: March 16, 2009, 4:43 pm
by kstones63
That is looking good so far. :) I sprayed mine with Sherwin WIlliams Direct to metal high build primer. You can spray it on really heavy and it will fill a lot of imperfections and waves in the metal. THis material block sands very easy to make a great finish. Mine is going to paint on the 28th (hopefully) so I will know then how the primer did work.
Keep up the good work. You need lots of patience and time.
Kevin

Posted: March 16, 2009, 8:05 pm
by Phil
kstones63 wrote:You need lots of patience and time.
Kevin
I am failing on both counts on this one. I also lack space :evil:

Posted: March 17, 2009, 2:26 pm
by Phil
Some progress

Took a 1/2 day today and shot PPG K36 Surfacer primer. 4 coats.

Only a couple disasters.
I put the trunklid on the stand and I must have gotten some paint stripper on it. It crinkled the epoxy a little.
Either that or its not completely cured and the foam wrap got into it. Either is a bad deal. I think its OK though.
I cleaned it all up with degreaser and set it in the sun for an hour or so then shot it.
The 1st coat didn't react so after 15 min I did another coat.

Other disasters: I kicked over a can of K 36 :evil: And $pilled about 3/4 cup.

I am beat but I plan to drag out the hood and start working it over.

Image

pic of my truk off the balcony with its Ram bed cover :oops:

Image

Posted: March 17, 2009, 2:40 pm
by Greg D
You are getting ALOT more done than me. That metallic blue with the white stripes would look pretty cool on your Uni, I add an early Mustang style side strip too IMHO though.
Looking good Phil.

Posted: March 17, 2009, 9:01 pm
by scoutmaster
phil, your car is looking good . it sure looks like alot of work but i'm sure it will be good to say you did it yourself.
See Ya!
Dave

Posted: March 17, 2009, 11:14 pm
by DCarr
Phil ,I now have no more excuses-I must do my own paint. Thanks for the update
& the confidence booster. The parts are looking good.

Posted: March 18, 2009, 6:22 am
by Phil
So far things are OK. Ive been OK with shooting primer outside, you sand a lot off anyway. When its warm the Bondo hardens well, you have plenty of light to work in and lots of space. Unfortunately I live in the city so I require tolerant neighbors.

Now that I am onto paint stage I am a little worried about how to handle it. I have access to a spray booth at work but I have to be low-key about it. Hard to do with fenders the size of a couch. Yesterday it was 70 degrees so it was cake. Its supposed to be raining and 67 today and I work all day. The next 10 days its under 50 deg.

I still have doors and fenders to sand and a hood to fix so maybe I can have it all ready for paint at the same time. In a perfect world Id assemble the car now and sand it all together for straightness and shoot it all at once. As it is I may avoid runs with doing it with individual stuff laying down on a bench

The worst thing yesterday was I decided to clean out my garage in prep for spraying. I moved the car outside and looked at the "good" side that has been against the wall. The *%$#ing painter left a huge run the full length of the quarter. I am seriously considering redoing his work when the rest is sprayed. The other quarter looks like it was done with his face.

I did get the trunk, extensions, cowl panel, stone guard, hood lip and scoop ready for painting at the end of last night.

Posted: March 18, 2009, 7:05 am
by Greg D
With your space constraints you may consider this option.
90% of a good paint job is prep, you obviously have that handled.
You could edge & inside paint all of it at home.
Assemble, align & block it down.
Drive it to MAACO for the final color coats.
This has been done as a low buck paint job in most of the major magazines for years. The down side of the cheap MAACO paint jobs is the lack of proper prep - you have that done though. They do a good job spraying the paint at those places and probably get more practice than your average body shop. Wouldn't cost you a nickle to give them a call about it. You are now looking at a final coat for the whole car so this could be a good option for you.
Just a thought.