Slick 60's

Hey Ya'll

I plan on hitting up these cruise-ins. Thought I'd post the list here, I got it from the Creepers Club website.

1st Sat, Apr-Oct Villa Rica, GA - West GA Street Rodders 12th Annual Cruises, Ingles Shopping Center, Hwy 61, I-20 exit 24 - 5:00PM until ????
1st Sat, Mar-Oct Cartersville, GA - Train Depot & Welcome Center

2nd Sat, Apr-Sept Macon, GA - Mable White Baptist Church on Bass Road, 6:00 to 9:00 PM

2nd Sat, Apr-Oct Marietta, GA - Wendy's West Cobb Market Place

3rd Sat, Apr-Oct Canton, GA - Cruise Night at Riverstone Plaza, Po Boys Car Club.

4th Sat, Apr-Oct Cartersville, GA - Hwy. 41 & Main Street

4th Sat, Apr-Oct Dallas, GA - Main Street, Downtown

5th Sat, May & Aug Powder Springs, GA - Cruise night on the town square in Powder Springs



Also, there's a show in Dallas at Paulding Meadows, April 25th. Push Rods club show in Powder Springs, October 31st. I'll post up more as I find the schedules.

Im a member and live in Paulding county. Planning on getting to some of the cruise ins. Would like to meet you. Currently building 2 Unibodys. There not road worthy yet.

Where at in Paulding? I'm in SW Paulding/Temple/Villa Rica area. I went to the Villa Rica cruise in. Those folks don't stay out late at ALL. 7:30 and they were leaving, I was like, what the crap, I just got here. Saw one slick, and a nice panel '55. Will post pics later.

I live off of Cedar Crest Road a few miles off Hwy 41 close to Bartow County. I have owned a dozen slicks through the years. Im currently putting a 2002 Lightning motor and trans in my 63 unibody. I also bought a 61 unibody a few weeks ago in Senoia found it on craigslist. Look forward to meeting you. Plan to make some of the cruise ins. I would post some pics but can not figure out how.

I might drive over one cruise-in night to meet you guys this summer. It's not that far from Birmingham, I just made that drive the other day to pick up a motorcycle for a friend. My 4.6 and overdrive in my slick should not use much fuel once it is up and going.

Deviant1 are you going to run fuel injection or carb on your 4.6?

Cool to see a drive in in Macon. I've not heard of it yet.
I'm going to B'ham for the 45 anny MCA Mustang show with the mach 1.

Power by Ford wrote:Deviant1 are you going to run fuel injection or carb on your 4.6?

I am using fuel injection. I have already had it running briefly, just need the cooling system finished and the exhaust beyond the headers finished.

66 POJ, The mustang event in B'ham is just a few minutes from the house. It should very fun. I have my camera ready to snap some pics.

deviant1 wrote:66 POJ, The mustang event in B'ham is just a few minutes from the house. It should very fun. I have my camera ready to snap some pics.

I will be there Saturday with a group of Mach 1's from http://www.mach1registry.org/forums/index.php

So far I think its around 2000 Mustangs signed up.

deviant1 did you use the factory harness or aftermarket? There is so much unneeded stuff in the factory harness it is going to take alot of time to clean up Im considering one form the Detail zone. Any pointers would be appreaciated.

Power by Ford, I am using a factory harness. I spent many hours finding out exactly where each wire in the harness went and what it did. After I was sure I did not need something, I would remove it usually by unpinning the wire from a connector. If you have not already, go to ModularFords.com and look around...that site has pinouts for about any moduar powered vehicle.
To keep things cleaner and simpler, I made up my own little panel to mount all the important relays and fuses. This made the wiring easier also.

Add to the list:

The Galaxy Diner, the 1st Saturday of every month.
http://www.galaxydineratlanta.com/page17.htm

Tucker Cruise-ins, the 2nd Saturday of every month.
http://www.tuckercruisein.com/Events.html

I usually attend these as they are right around the corner from me.