302 to 351w t5 swap questions

A place for discussion of off topic subjects. Pretty much anything goes - just keep it civil, please!

Moderators: Casey 65, Kid

Post Reply
64 f100
Posts: 2754
Joined: July 18, 2006, 7:23 am
Location: Carmi, Illinois, 62821

302 to 351w t5 swap questions

Post by 64 f100 »

As some of you may or may not know, My grandson and I recently purchased 66 stepside with a 351w already installed. Unfortunately, the install was done poorly, with a later 4 speed granny tranny. Mostly a butcher job. Cut out the crossmember, butchered floor. etc. Fairly certain the orignal 352 engine stands were used, which led to clutch linkage problems, which offset the z-bar, and caused the throwout arm to be forced sideways. This in turn caused the throwout bearing to ride oddly on the pressure plate causing the fingers to wear out. Clutch plate was in good condition. Flywheel need resurfacing.
Anyway, this has brought me to changing the transmission to something more user freindly, and a little better on gas. My options are a 4 speed overdrive cast iron transmission from a 78-9 Granada, 4 speed aluminum type from 78 Mustang, or van, or a recently acquired T5. I have no bellhousing or flywheel for the T5, but do have the front dust cover. So I'm wondering what options I have. I have the 11 inch clutch setup for the 351w but don't know whether this would work with a T5 bellhousing. I don't have a 28 ounce flywheel for the T5 otherwise, which is obviously of smaller diameter, than the 11 inch I have. Other options include buying an adaptor for the T5, roughly 130$. However, I'm uncertain that this will work with the truck bellhousing I have. Along with these problems, I'm wondering how shifting location on the T5, and shifter length will work out if I use the T5. I do have a set of 2001 bucket seats I can install in the truck, to help in location, but still wondering about a shifter and if it will have to be lengthened to accomidate working in a truck. This will obviously lengthen the throw on the shift.

Questions
1. What flywheel can I use with the t5 bellhousing that is 28 ounce?
2. Will the adapter be user freindly?
3. Will the aluminum 4 speed hold up?

Any suggestions?

Thanks,
Rich
User avatar
Hawkrod
Posts: 1359
Joined: July 21, 2006, 10:57 pm
Location: Apple Valley CA
United States of America

Post by Hawkrod »

The bellhousing you have now will work with an adapter and is probably the easiest way to go. You could buy a T5 bellhousing and use an early 60's 221-260-289 small flywheel and that will work but then you need to deal with clutch linkage as the T5 will be a pull cable setup. As far as the shifter location is concerned, I have taken Ford T5's and mated Chevy S10 tailshaft suff to it to get a forward shift location. It is fairly straightforward and S10 T5's are cheap and easy to get. Hawkrod
User avatar
Johnny Canuck
Posts: 8291
Joined: April 9, 2006, 11:14 pm
Location: Edmonton, Alberta.
Canada

Post by Johnny Canuck »

Rich I dunno if the '78 is the same as the '79 4 spd OD with the aluminum case, but the one (actually 2) I had was a real POS, and I wouldn't recommend it to my worst enemy.
Had to rebuild second gear and all the synchros at 52000 miles. Glass gears they called them, and that was behind a smogged out 302 with barely over a hundred horses. I'm sure it would just fly apart behind a 351. Go with something else besides the aluminum case one, IMHO.
It's a race.. Will hell freeze over or will JC finish his truck first. Stay tuned..
Post Reply