MadMaxetc's 1963 Build
- slickmainer
- Posts: 2555
- Joined: October 8, 2007, 6:41 pm
- Location: Auburn Maine
- Contact:

All in good time...all in good time.Max wrote:Awesome sized shop! I have enough crap for half of that right now but in a week would probably have it filled up.
Now you need some good ol tin signs for the walls, good sound system, the before-mentioned fridge and you're fallout shelter/bunker is complete!!
You bet its a good deal. The pole barn system is the most economical way to go. My building was put up by Morton buildings. Morton is a little more pricey but they are hard to beat. They have the best warranty in the business and absolutely stand behind it. When they were putting up my building I ask how much weight I could lift on one of the trust. The guy said it is designed to hold X number of pounds of snow load, you could lift an engine with it if you wanted. I have a chain hoist hanging on one of the trust and while I have never tried lifting an engine I have used it to lift the cab and the bed off and back on my truck. The investment in a good shop is priceless, it will pay you back many times over.MadMaxetc wrote:I had it built by "The Barn Guys"Michelle wrote:Who did you buy your building from?
$19k in it right now. After Electrical and Finishing the inside it shouls be less than $25k
Very good deal for 30' x 40'.
Chris, you should come down and see it some time!
Michelle
Democracy is two wolves and a sheep voting on what to have for dinner. A Republic is a well-armed sheep.
I hope I always stay crazy, because I know if I ever become sane, it will drive me crazy.
Democracy is two wolves and a sheep voting on what to have for dinner. A Republic is a well-armed sheep.
I hope I always stay crazy, because I know if I ever become sane, it will drive me crazy.
- Alan Mclennan
- Posts: 9324
- Joined: October 14, 2006, 6:16 pm
- Location: In the shed... Cranebrook NSW

Maybe an Aussie number plate might fit as well!Max wrote:Awesome sized shop! I have enough crap for half of that right now but in a week would probably have it filled up.
Now you need some good ol tin signs for the walls, good sound system, the before-mentioned fridge and you're fallout shelter/bunker is complete!!
Honey, If I say I`ll fix something I will, there`s no need to remind me every 6 months!!
66 f100 tabletop swb 351 Clevo C6 "Beryl"
Slick Stock 3 KCMO
Slick Stock 4 Altoona
Slick Stock 5 KCMO
Slick Stock 6 Altoona
Slick Stock 7 Salina KS
Slick Stock 8..............................
66 f100 tabletop swb 351 Clevo C6 "Beryl"
Slick Stock 3 KCMO
Slick Stock 4 Altoona
Slick Stock 5 KCMO
Slick Stock 6 Altoona
Slick Stock 7 Salina KS
Slick Stock 8..............................
- dotcentral
- Posts: 1341
- Joined: August 18, 2006, 5:13 pm
- Location: Charlotte, NC
I think that would be cool to have plates from all different states and countries.Alan Mclennan wrote:Maybe an Aussie number plate might fit as well!Max wrote:Awesome sized shop! I have enough crap for half of that right now but in a week would probably have it filled up.
Now you need some good ol tin signs for the walls, good sound system, the before-mentioned fridge and you're fallout shelter/bunker is complete!!
Think you could bring an old one next time you come to see us Yanks!?
- Alan Mclennan
- Posts: 9324
- Joined: October 14, 2006, 6:16 pm
- Location: In the shed... Cranebrook NSW

I have been collecting license plates since I was a kid. I have boxes of plates stored. I have a complete collection of Texas plates from the first one until the 80's. Past the 80's they are not much fun as they all has stickers. I have plates from all states and Canadian provinces. I even have a bicentennial collection from ever state (even the states that did not issue a bicentennial plate I have a 76 plate) I have a large collection of truck plates as well. I also have a birth year collection. I could wall paper my shop with them, but I need the space to hang parts and other junk.MadMaxetc wrote:I think that would be cool to have plates from all different states and countries.Alan Mclennan wrote:Maybe an Aussie number plate might fit as well!Max wrote:Awesome sized shop! I have enough crap for half of that right now but in a week would probably have it filled up.
Now you need some good ol tin signs for the walls, good sound system, the before-mentioned fridge and you're fallout shelter/bunker is complete!!
Think you could bring an old one next time you come to see us Yanks!?
Michelle
Democracy is two wolves and a sheep voting on what to have for dinner. A Republic is a well-armed sheep.
I hope I always stay crazy, because I know if I ever become sane, it will drive me crazy.
Democracy is two wolves and a sheep voting on what to have for dinner. A Republic is a well-armed sheep.
I hope I always stay crazy, because I know if I ever become sane, it will drive me crazy.
- Alan Mclennan
- Posts: 9324
- Joined: October 14, 2006, 6:16 pm
- Location: In the shed... Cranebrook NSW

Yes Michelle!, but have you got an Aussie one yet?, see you in Iowa! 
Honey, If I say I`ll fix something I will, there`s no need to remind me every 6 months!!
66 f100 tabletop swb 351 Clevo C6 "Beryl"
Slick Stock 3 KCMO
Slick Stock 4 Altoona
Slick Stock 5 KCMO
Slick Stock 6 Altoona
Slick Stock 7 Salina KS
Slick Stock 8..............................
66 f100 tabletop swb 351 Clevo C6 "Beryl"
Slick Stock 3 KCMO
Slick Stock 4 Altoona
Slick Stock 5 KCMO
Slick Stock 6 Altoona
Slick Stock 7 Salina KS
Slick Stock 8..............................
I don't thank I do have an Aussie plate yet.Alan Mclennan wrote:Yes Michelle!, but have you got an Aussie one yet?, see you in Iowa!
Michelle
Democracy is two wolves and a sheep voting on what to have for dinner. A Republic is a well-armed sheep.
I hope I always stay crazy, because I know if I ever become sane, it will drive me crazy.
Democracy is two wolves and a sheep voting on what to have for dinner. A Republic is a well-armed sheep.
I hope I always stay crazy, because I know if I ever become sane, it will drive me crazy.
I need your guys thought on something.
In the new shop, I was going to put down the epoxy floor covering. I got 4 gal at the ace than whent out of bizz for 70% off. The problem is, I didn't get enough. If I get more at full price I will go out of my budget. Keep in mind that I am going to get bought out by the city in 10 years.
So:
Do I spend another $400 and do it.
Or do I use what I have in the garage and just do a bare floor in the Shop?
In the new shop, I was going to put down the epoxy floor covering. I got 4 gal at the ace than whent out of bizz for 70% off. The problem is, I didn't get enough. If I get more at full price I will go out of my budget. Keep in mind that I am going to get bought out by the city in 10 years.
So:
Do I spend another $400 and do it.
Or do I use what I have in the garage and just do a bare floor in the Shop?
Me personally, I wouldn't do it unless I covered the whole floor. But, you could get creative and say leave the area around the workbench bare and just do where the trucks are parked or something like that...
"If you don't want to stand behind our Troops, feel free to stand in front of them."
1964 Ford F100
1967 US Army M416
1964 Ford F100
1967 US Army M416
If you are going to do a lot of welding in your shop, you might think about leaving a section devoted only to welding and grinding. The weld splatter will pit the epoxy and leave it looking terrible in short order. The heat is what melts the epoxy.
I have my parking garages epoxy coated and think they are great. I only did the final assembly in this garage so I didn't do any welding in it. I thought about doing my shop but a painter friend that does garage coatings talked me out of it because of the amount of welding that I do.
For what it's worth, the epoxy coatings look great, are easy to take care of and I think would help the appraisal value on the house. Only you know how much damage that you will do to the floor.
I hope this helps,
Kevin
I have my parking garages epoxy coated and think they are great. I only did the final assembly in this garage so I didn't do any welding in it. I thought about doing my shop but a painter friend that does garage coatings talked me out of it because of the amount of welding that I do.
For what it's worth, the epoxy coatings look great, are easy to take care of and I think would help the appraisal value on the house. Only you know how much damage that you will do to the floor.
I hope this helps,
Kevin
kstones63
_______________________________________
63 F100
29 Ford Sedan Delivery
99 F250 PSD, 4x4, CC
95 F350 Flatbed Dually Diesel
_______________________________________
63 F100
29 Ford Sedan Delivery
99 F250 PSD, 4x4, CC
95 F350 Flatbed Dually Diesel
That does help. I will be doing a lot of welding. I also don't think it will help in the resale value because i will most likely get bought out by the city. I am also getting toward the High end of what I could sell this place for already.kstones63 wrote:If you are going to do a lot of welding in your shop, you might think about leaving a section devoted only to welding and grinding. The weld splatter will pit the epoxy and leave it looking terrible in short order. The heat is what melts the epoxy.
I have my parking garages epoxy coated and think they are great. I only did the final assembly in this garage so I didn't do any welding in it. I thought about doing my shop but a painter friend that does garage coatings talked me out of it because of the amount of welding that I do.
For what it's worth, the epoxy coatings look great, are easy to take care of and I think would help the appraisal value on the house. Only you know how much damage that you will do to the floor.
I hope this helps,
Kevin
