352 distributor removal

The place to talk Slicks. All we ask is that discussion has something to do with slicks...

Moderators: Casey 65, Kid

Post Reply
hubbtomdaman
Posts: 12
Joined: July 4, 2013, 11:35 am
United States of America

352 distributor removal

Post by hubbtomdaman »

I have a 66 F100 with a 352,it has sat for quite a few years and there was like grude rust goop all over the valves train,got it all cleaned up real nice,now I have been trying to get the distributor set,but it would not move,had to use a 2' pipe wrench and finally broke it free.Worked it back and forth until it spins freely all around,problem is the distributor is recessed to deep into the intake that the hold down dosnt even come close to holding it in place.Noticed when I had finally loosened the distributor at the base where it fits into the manifold,there appeared to be like rubber rolling out,is there a seal or gasket that needs to be replaced? I cant get the distibutor to pull out completely,I have beat on it still nothing,I was not going to pull it but there is no way to tighten down the distributor.is there anything holding the distributor in place internally? Hope someone can help,until then I will continue to beat on it and hope I dont break anything!!!
I was prying up on the distributor I was able to get it to come out or at least part of it!!! The top of the distributor along with the center shaft came out,the casing an 1" below where its fits to the top of the intake manifold broke,leaving the remaining lower section of the distributor firmly in place,seated in the bottom of the intake manifold,along with the drive gear,looks like I will be taking the intake off and hopefully get the rest of the distributor out,will call the salvage yards to get another distributor also. I have another question? When I was turning the main crank to find TDC on #1 cylinder to line up #1 position on the distributor,after turning the crank one more complete rotation #1 cylinder was at TDC but the position on the distributor was 180 opposite.How do you know which position on the distributor is #1, when #1 cylinder TDC shows at two different spots on the distributor? How do you know which one is 180 out? Sorry for the stupid question but I'm have brain freeze or old age,probably both.
Thanks for your help
User avatar
Toyz
Posts: 4334
Joined: March 22, 2011, 6:23 pm
Location: Baja Houston Taxes
United States of America

Re: 352 distributor removal

Post by Toyz »

OK, hopefully in order:
Yes, there is an o-ring which seals the distributor to the block.
The stuck shaft is probably a combination of a sludged up and a frozen oil pump drive shaft and the retainer which is supposed to hold it from coming out with the distributor. This would require removing the oil pan and pump if it will not release, which probably needs to be done, anyway, to assess oil pump and pickup condition.
A good penetrant such as PB Blaster or others is definitely helpful in this, especially if given time to soak and penetrate.
The crankshaft makes two revolutions for every cycle, while the cam makes one.
In order to verify TDC on firing stroke, watch # 1 intake valve while turning the engine; immediately after it closes, you will be in the vicinity of the timing mark , and thus, can set timing to #1 cylinder on the distributor.
Note that any "goop" or sludge loosened from the engine internals WILL find it's way to the oil pan and oil pump screen(which is probably already in bad shape. You will need to remove all possible sludge. My suggestions would be Berryman B-12 or Seafoam, and a bunch of diesel prior to pan removal. Frequent oil/filter changes will be mandated after getting it running.
Hydraulic lifters may be a problem; liberal additions of the B-12 or Seafoam may alleviate such problems.
Good luck! I'm sure others will reply with their personal methods and approaches.
BTW, rebuilt distributors are relatively inexpensive; I would not personally bother with a used one unless it was exceptional.
There's plenty of distributor discussion on this site for reference.
Paul
The Ford Orphanage
Life's too short for boring vehicles!
My quest to develop a universal solvent is held up by the lack of a storage container.
Paul
hubbtomdaman
Posts: 12
Joined: July 4, 2013, 11:35 am
United States of America

Re: 352 distributor removal

Post by hubbtomdaman »

Thanks for the info,
Kinda figured I'd have to drop the pan,should have done that from the get go,was just hoping I could nurse it back without having to do all that. Will I be able to drop the pan without pulling the engine,looks like there is enough room,but looks can be decieving. You mentioned using deisel ,Berrymans B 12 or Seafoam, I put fresh oil in her when I started,considering I wont be able to run the engine how should I apply any or all of these,let it mix with the oil or drian and spray down the internals with it
User avatar
Toyz
Posts: 4334
Joined: March 22, 2011, 6:23 pm
Location: Baja Houston Taxes
United States of America

Re: 352 distributor removal

Post by Toyz »

Since you will have the pan off; you can spray down the internals with aerosol B-12, or even carburetor cleaner. On re-assembly and start-up, I would add a pint of Seafoam or B-12 to the engine oil.
You will probably want to closely inspect or replace the oil pump and pickup. Be sure to use a Motorcraft oil filter for reasons described in other topic areas.
Depending on where the distributor came apart, removing that boat anchor intake may be a substantial chore. You will probably find an abundance of sludge in the engine valley and tray.
The pan can be removed with engine in place. Engine needs to be raised to install one inch blocks at engine mounts.
Once pan bolts are removed and pan loosened; remove the oil pump retainers and pump. The crank may have to be rotated to allow pan to be fully removed.
Paul
The Ford Orphanage
Life's too short for boring vehicles!
My quest to develop a universal solvent is held up by the lack of a storage container.
Paul
hubbtomdaman
Posts: 12
Joined: July 4, 2013, 11:35 am
United States of America

Re: 352 distributor removal

Post by hubbtomdaman »

Thanks Paul,
appreciate you sharing your knowledge with me,looks like I have a little work ahead of me.Ihave heard that the intake is pretty heavy,but wiil definatly have to come off,appears that the distributor is frozen toit on the inside ,looking in the intake.Oh well at least I will be able to inspect he inside of the engine to see what other surprises are there for me.Wasnt really ok with the idea of running the engine with all that crude in it,thinking it would work its way up into the heads and cause me a whole ton of greaf by scouring the heck out of the cylinder walls.Off to the bone yard for a distributor and parts store for some gaskets,fun day Ay.good thing its a labor of love
LM14
Posts: 1755
Joined: August 22, 2009, 10:44 pm
Location: Bloomfield, Iowa
United States of America

Re: 352 distributor removal

Post by LM14 »

Use and engine hoist to lift the intake. It's the safest way to do it they are so heavy.

SP
1932 Ford 5 window coupe. 302/C4
1962 8V-390/C6 Unibody Short Bed Soon to be Big Window - The Lincoln that never was
2013 F150 Super Crew Eco Boost 4x4
2015 Ford Edge for the little lady, because she said so!
2007 Mustang GT, 4.6-3V/5 Speed. Only 8680 miles on the clock.

More toys, I need more toys!!!
hubbtomdaman
Posts: 12
Joined: July 4, 2013, 11:35 am
United States of America

Re: 352 distributor removal

Post by hubbtomdaman »

I was able to get a new distributor,origanal equipment,called all around and finally foumd one for $70.Pulled the intake,WOW,there was alot of crud,enough to fill a oil filter box! Pulled the Oil Pan,it did not look to bad,sum sludge,pump and screen not to bad,bottom end doesnt look bad at all,timing chain cover had same crud crap all in it.The distributor is frozen to the block portal,looks like the aluminum distributor and the cast iron combined with moisture has really done a job,tryed to get it out with a chisel,hasnt budged a bit,resolved to start drilling it out,hoping I will be able to get all the shavings flushed out.Iwas going to pull the heads since its tore down this far,but as anticipated,the exhaust manifold bolts are so rusted that a socket wont fit tight enough to get a firm hold and they are starting to round out,not good,since I cant pull the motor I will have to forget about doing anything with the valves.Do you have any suggestions on how to remove old rusty exhuast manifold bolts,I only tried one bolt so far,want to wait to hear from someone who has experience with this issue,thanks
User avatar
unibody madness
Posts: 2147
Joined: December 4, 2008, 4:33 pm
Location: Paradise,CALIFORNIA 95969
United States of America

Re: 352 distributor removal

Post by unibody madness »

If you have a welder weld some new nuts over the old bolt heads, after cleaning them well of course. This will give you new metal to wrench on, and the heat will help loosen them up.
Spend a few days spraying them with a 50/50 mix of atf and acetone, or Kroil oil to help loosen them up
Turk build thread at:
http://slick60s.com/viewtopic.php?f=32&t=18944

It does not matter what you think, it only matters what you do about it!
User avatar
Toyz
Posts: 4334
Joined: March 22, 2011, 6:23 pm
Location: Baja Houston Taxes
United States of America

Re: 352 distributor removal

Post by Toyz »

Luckily; I haven't needed to mess with such in years.
Temperature extremes are your friend; a torch, even propane, dry ice, a bottle of nitrogen :shock: ; anything to shock the metals.
There are several "freeze" type aerosol penetrants on the market now. They may be of some help by combining solvents with the freezing effects.
Be sure to remove the oil pump in order to free the distributor drive shaft; it is usually a prime source of resistance , especially with gummed up tolerances and the retainer clip.
I know this is getting more involved than you anticipated, but you have made a major step toward head removal; it is probably simpler to just bite the bullet and remove the heads. Get a good six point socket and remove the manifold to exhaust pipe fasteners; using plenty of penetrant and heat as mentioned.
Unfortunately, removing the exhaust manifolds will probably result in broken fasteners, and that is considerably easier to deal with on the bench.
I would expect your valve seals to be damaged or non-existent; this can easily be addressed with the heads removed.
Again good luck; it's a tough job, but totally do-able.
Paul
The Ford Orphanage
Life's too short for boring vehicles!
My quest to develop a universal solvent is held up by the lack of a storage container.
Paul
hubbtomdaman
Posts: 12
Joined: July 4, 2013, 11:35 am
United States of America

Re: 352 distributor removal

Post by hubbtomdaman »

I dont have the resources,Yetmto weld heads on the old bolts,but like you said since I already have every thing esle pulled,and the new seals and head gaskets that came with the gaskets set I really wanted to replace them,oh well its not in the cards for right now,
Thanks Paul
longcabjohn
Posts: 356
Joined: January 21, 2012, 1:08 pm
Location: waverly, Tn
United States of America

Re: 352 distributor removal

Post by longcabjohn »

Try metric socket, sometime they work like inbetween standard sizes.



Johnny
If restoring a ford was easy, chevy guys could do it.
hubbtomdaman
Posts: 12
Joined: July 4, 2013, 11:35 am
United States of America

Re: 352 distributor removal

Post by hubbtomdaman »

Been a few days since I last posted,between work and other obligations,I did'nt get a whole lot done.I finally got the distributor out by drilling it out with six holes and breaking it into peices then fishing out the gear.I fudged up the opening at the top of the block a little,about 1/5th of the back seating surface was chipped away or drilled out,but the distributor seats in the block after using a fine round file,so I'm pretty confident it will be alright once the intake is in place and the distributor hold down is in place.I really want to pull the heads considering I have the motor tore down this far and that the fresh oil I put in before I ran into the distributor issue,looked real creamy after only turning it over to see if it would start,makes me believe there is a head gasket leak.I been thinking I could drop the exhaust pipes and pull the heads with the manifolds attached then mess with the manifold bolts once their off,they will be easier to get to anyways.I sprayed it down with trans/naptha and will again for the next two days in preparation for this weekend.Do you have any suggestions you can pass on to me about any of this? Thanks in advance
Tom
User avatar
Toyz
Posts: 4334
Joined: March 22, 2011, 6:23 pm
Location: Baja Houston Taxes
United States of America

Re: 352 distributor removal

Post by Toyz »

I almost always pull the manifolds with the heads. IMO I prefer to tear up the exhaust studs as required, then repair everything on the bench.
Paul
The Ford Orphanage
Life's too short for boring vehicles!
My quest to develop a universal solvent is held up by the lack of a storage container.
Paul
hubbtomdaman
Posts: 12
Joined: July 4, 2013, 11:35 am
United States of America

Re: 352 distributor removal

Post by hubbtomdaman »

Makes sence to pull the maniflods with heads,will be alot easier to mess with those bolts when there will be plenty of room.I should have paid closer attention to the post you made before about removing the manifolds and heads as one,sorry,I was thinking more about using heat and cold to loosen everything.Do I have to worry about the metal cracking from the extreme heat / cold differences,I will be using a propane torch and whatever type of freezing agent I can find,any suggestions? How long should I apply heat and or cold,do you heat up just the bolt or the area around it? I have never done it before and dont want to mess/crack anything? What do you think about the area on the top of the block where the distributor sets in that I messed up a little,will that effect anything?
User avatar
Toyz
Posts: 4334
Joined: March 22, 2011, 6:23 pm
Location: Baja Houston Taxes
United States of America

Re: 352 distributor removal

Post by Toyz »

hubbtomdaman wrote:Makes sence to pull the maniflods with heads,will be alot easier to mess with those bolts when there will be plenty of room.I should have paid closer attention to the post you made before about removing the manifolds and heads as one,sorry,I was thinking more about using heat and cold to loosen everything.Do I have to worry about the metal cracking from the extreme heat / cold differences,I will be using a propane torch and whatever type of freezing agent I can find,any suggestions? How long should I apply heat and or cold,do you heat up just the bolt or the area around it? I have never done it before and dont want to mess/crack anything? What do you think about the area on the top of the block where the distributor sets in that I messed up a little,will that effect anything?
Those manifolds can be somewhat sensitive; I've never cracked one with a torch, and I don't think it's likely with propane, but it's a possibility. It is hard to get the heat/ chill where needed, although heating the hex end of the bolt may relieve tension enough to help. good solvents will definitely help, especially if given a long time to soak.
I would rap on the bolt heads with a fairly large hammer, then try a good six point socket. If you use a breakover bar, you can apply pressure while rapping the business end of the bar with the hammer. Any which don't respond would get chiseled/ground/drilled enough to allow manifold removal. This then allows access to the remaining capscrew to both heat and use a small pipe wrench to aid removal. If any should break off flush with the head, then careful drilling for removal, or just enough for an easy-out, would be required.
If you are uncomfortable with removal progress, just take the heads with manifolds to a local machine shop for removal. They usually know plenty of tricks to make the job fairly easy and inexpensive.
Paul
The Ford Orphanage
Life's too short for boring vehicles!
My quest to develop a universal solvent is held up by the lack of a storage container.
Paul
hubbtomdaman
Posts: 12
Joined: July 4, 2013, 11:35 am
United States of America

Re: 352 distributor removal

Post by hubbtomdaman »

Thanks Paul,
I really appriciate all your advice.Sprayed everything down again with trans/naptha,feeling pretty confident in getting those heads off.Do you have any suggestions on what type of freezing agent/name,and what do you think about the distributor seat/mount at the top of the block that I messed up a bit,should I worry about it?
User avatar
Toyz
Posts: 4334
Joined: March 22, 2011, 6:23 pm
Location: Baja Houston Taxes
United States of America

Re: 352 distributor removal

Post by Toyz »

I'm not sure one of the "freezing" products will do much good due to lack of direct access. If the capscrews are galled or frozen through the manifold, the shocking action might help. Most time, the capscrew is locked in the threaded area. I'll have to look tomorrow for the brand name I have on hand. As previously noted, I have managed to escape such needs for some time.
I suspect a solvent product with "capillary" action such as PB Blaster, Knock'erLoose, or Kroil is probably as effective in your situation.
As to the distributor, if the damage is in the sealing area, you may have to resort to a non-hardening sealant such as #2 Permatex to insure integrity. A hardening or anaerobic sealant might make it extremely hard to adjust timing. Make certain the oil pump driveshaft has the retainer clip at the distributor end. If the damage is not directly in any sealing area, it should pose no problem once burring is cleaned up.
Paul
The Ford Orphanage
Life's too short for boring vehicles!
My quest to develop a universal solvent is held up by the lack of a storage container.
Paul
hubbtomdaman
Posts: 12
Joined: July 4, 2013, 11:35 am
United States of America

Re: 352 distributor removal

Post by hubbtomdaman »

Thanks again Paul,
I have been talking to a few guys at work and they believe I will be able to get the manifold bolts loose with a propane torch,we will see.I dont think the distributor actually seals at the top of the block, justs fits snug and there is no o-ring on the distributor at that location where it makes contact with the block,should be ok.Any last words of advice using a propane torch to loosen bolts before I tackle it tomorrow?
User avatar
Toyz
Posts: 4334
Joined: March 22, 2011, 6:23 pm
Location: Baja Houston Taxes
United States of America

Re: 352 distributor removal

Post by Toyz »

I guess I could play Mom and add "be aware of trapped solvents", but that's not much of an issue with a propane torch :lol: You likely will have no problems; definitely less than trying to remove in place.
Best of luck!
Paul
The Ford Orphanage
Life's too short for boring vehicles!
My quest to develop a universal solvent is held up by the lack of a storage container.
Paul
hubbtomdaman
Posts: 12
Joined: July 4, 2013, 11:35 am
United States of America

Re: 352 distributor removal

Post by hubbtomdaman »

Thanks again for your time Mom,just kidding,I am really appriciative for your advice,will let you know how it turns out/off
Post Reply