Mid-70s Torino

A place for discussion of off topic subjects. Pretty much anything goes - just keep it civil, please!

Moderators: Casey 65, Kid

Post Reply
User avatar
slixtyfive
Posts: 458
Joined: January 19, 2007, 2:03 pm
Location: Eastern Iowa
United States of America

Mid-70s Torino

Post by slixtyfive »

Does anyone here have access to a 1972-1976 Torino? I need a measurement across the roof if you can help!

Thanks
"It's better to be gone but not forgotten, than to be forgotten but not gone." Gary Allan
36truck
Posts: 3152
Joined: October 20, 2007, 8:32 pm
Location: Land of Sunshine AZ
United States of America

Re: Mid-70s Torino

Post by 36truck »

I will be able to measure that for you when I get back to MI. Next week. If someone else can do it sooner that would be good.
Tom Williams
User avatar
slixtyfive
Posts: 458
Joined: January 19, 2007, 2:03 pm
Location: Eastern Iowa
United States of America

Re: Mid-70s Torino

Post by slixtyfive »

That would be great - i'm actually needing two dimensions across the roof from side to side:

1. the width at the bottom lip along the sides (top of door)
2. the width at the 'body line' where the roof turns down along the sides.

Thanks much!
"It's better to be gone but not forgotten, than to be forgotten but not gone." Gary Allan
36truck
Posts: 3152
Joined: October 20, 2007, 8:32 pm
Location: Land of Sunshine AZ
United States of America

Re: Mid-70s Torino

Post by 36truck »

Across roof side to side 4'4". I should have had my puter with me when I went to measure as I didn't get your other measurement. What are you trying to do? I can get a friend of mine to measure it for me later as he has some work to do for me.
Tom Williams
User avatar
slixtyfive
Posts: 458
Joined: January 19, 2007, 2:03 pm
Location: Eastern Iowa
United States of America

Re: Mid-70s Torino

Post by slixtyfive »

Thanks
Is the 4'-4" at the point where it bends down or at the point where the top of the doors meet up on the sides??

I've been gathering parts for a 'Vintage stock car' that will be comprised of a mustang body on a shortened torino frame. I can order a cage kit from Speedway for a torino(frame and body) which will obviously work with the frame but I'm trying to figure out if that cage will work for the mustang roof. (concern is that the cage 'halo' will be too wide)

Unfortunately, I gutted and scrapped the torino body a couple years back and didn't think to measure the roof before scrapping it......
"It's better to be gone but not forgotten, than to be forgotten but not gone." Gary Allan
36truck
Posts: 3152
Joined: October 20, 2007, 8:32 pm
Location: Land of Sunshine AZ
United States of America

Re: Mid-70s Torino

Post by 36truck »

The 4' 4' is the outside at the bend by the windshield. I would think you could cut down the cage if needed. Is the cage a kit? That would make it easy to modify. What year Mustang are you using the 71/73 should not be too far off.
Tom Williams
User avatar
slixtyfive
Posts: 458
Joined: January 19, 2007, 2:03 pm
Location: Eastern Iowa
United States of America

Re: Mid-70s Torino

Post by slixtyfive »

Thanks for the info - looks like it will be a bit too wide. I had also thought about narrowing it and that would work fine for the halo but chances are the main hoop (vertical behind driver) would also be too wide at the top. Narrowing that would make it not work with the frame.

Oh well, not a big deal to make a custom cage but was hoping to save some time with the pre-bent kit.

Thanks again for the help.
"It's better to be gone but not forgotten, than to be forgotten but not gone." Gary Allan
Post Reply