65 F250 with a 67 F250 Master cylinder

The place to talk Slicks. All we ask is that discussion has something to do with slicks...

Moderators: Casey 65, Kid

Post Reply
GarageTime
Posts: 9
Joined: July 27, 2014, 5:33 pm

65 F250 with a 67 F250 Master cylinder

Post by GarageTime »

Hey to all. First post. Thanks for your time. I've got a 1965 F250 with stock drums all around. I wanted to upgrade to a dual pot master cyl. The 1967 F250 had drums all around and a dual pot master.

I have a NOS 67 master. I dropped it in and put a longer push rod in to bring the pedal back up to correct the height. Just the slightest bit of free-play.

Everything is working as should. I did a "panic brake" test on a gravel drive. All four locked up and left equal slide marks. Steering wheel never pulled L or R.

So now the questions. (assuming I have the correct master cyl. with built in residual valves) Am I good to go? I've read that as long as long as I have the residual valves in place a proportioning valve is not needed on a all drum system. Is this correct? Some say otherwise.

Thanks again for any input or criticism. :wink:
LM14
Posts: 1755
Joined: August 22, 2009, 10:44 pm
Location: Bloomfield, Iowa
United States of America

Re: 65 F250 with a 67 F250 Master cylinder

Post by LM14 »

The '67 MC should have the 10# residual valves built in. If you don't have too much pedal travel or have to pump it up, go enjoy your ride!

SPark
1932 Ford 5 window coupe. 302/C4
1962 8V-390/C6 Unibody Short Bed Soon to be Big Window - The Lincoln that never was
2013 F150 Super Crew Eco Boost 4x4
2015 Ford Edge for the little lady, because she said so!
2007 Mustang GT, 4.6-3V/5 Speed. Only 8680 miles on the clock.

More toys, I need more toys!!!
GarageTime
Posts: 9
Joined: July 27, 2014, 5:33 pm

Re: 65 F250 with a 67 F250 Master cylinder

Post by GarageTime »

LM14 wrote:The '67 MC should have the 10# residual valves built in. If you don't have too much pedal travel or have to pump it up, go enjoy your ride!

SPark
Pedal is high and tight. No sponginess. No pumping. Now I just need to get my brake light switch install done.

Thanks SPark
User avatar
Blackwaterforge
Posts: 893
Joined: March 13, 2008, 9:22 am
Location: Alabama
Contact:
United States of America

Re: 65 F250 with a 67 F250 Master cylinder

Post by Blackwaterforge »

GarageTime wrote:Now I just need to get my brake light switch install done.
I used a electric brake light switch and mounted it in place of the rubber bumper on the brake pedal.


Image
Image

Image
If it cain't be fixed with a sledge hammer it must be an electrical problem!
GarageTime
Posts: 9
Joined: July 27, 2014, 5:33 pm

Re: 65 F250 with a 67 F250 Master cylinder

Post by GarageTime »

I was going to install an inline T at master and screw my pressure switch in and reconnect wires. 3/16 x 3/16 x 1/8 female NPT.

Any thoughts on this method?
User avatar
ezernut9mm
Posts: 9141
Joined: July 21, 2006, 9:37 pm
Location: KCMO
Sweden

Re: 65 F250 with a 67 F250 Master cylinder

Post by ezernut9mm »

seen it done a bunch of times. haven't heard of any problems associated with it.
always
"i believe i've achieved satisfaction".-bubbles
"should i be gettin" baked for this boys?"-bubbles


i could no longer keep "r.i.p.ing" all of our fallen brothers and sisters, so i say here, slick loads of love and much respect to all you beautiful people.
User avatar
foodstick
Posts: 3364
Joined: March 15, 2006, 6:45 pm

Re: 65 F250 with a 67 F250 Master cylinder

Post by foodstick »

You are off to a great start ! Nothing like good brakes on these trucks !
GarageTime
Posts: 9
Joined: July 27, 2014, 5:33 pm

Re: 65 F250 with a 67 F250 Master cylinder

Post by GarageTime »

Thanks for replies
The manual steering keeps my heart rate up.
But I'm getting too old to be "Living on the edge" with a bad brake set-up.
User avatar
bobenhotep
Posts: 911
Joined: January 9, 2007, 4:15 am
Location: Las Cruces, NM
Contact:
United States of America

Re: 65 F250 with a 67 F250 Master cylinder

Post by bobenhotep »

I mounted a switch to work off of the bumpstop bar on the brake pedal. I put it through the bracket above it. I don't like the pressure operated switches, they start leaking after a while and if they were so great they would have kept using them.

Dan
For every person with a spark of genius, there are a hundred with ignition trouble

My '63 short wrongbed

"The Iron Rhino"
300 I6, 3 spd manual, DS II/ HEI ignition.

Stuff I added to Hints and tricks

-300-6 choke tube repair
-duraspark II/ HEI
-Horn ring contact tube repair
-turn signal indicator fix




Mikhail Kalashnikov and Nikola Tesla are the guys i think of when i build things.

Image
ICEMAN6166
Posts: 11470
Joined: July 11, 2006, 11:28 am
Location: Dove Creek, Co. elevation 6842
Poland

Re: 65 F250 with a 67 F250 Master cylinder

Post by ICEMAN6166 »

GarageTime wrote:I was going to install an inline T at master and screw my pressure switch in and reconnect wires. 3/16 x 3/16 x 1/8 female NPT.

Any thoughts on this method?
thats how i did it, still working fine after 14 years.

on my 65 towtruck i removed the rubber from the pedal stop
(different style from the one above)
it worked but the pedal having no rubber banged against the switch and broke it after a while. i redid it using a full nut rather than the thin one supplied with the switch and that fixed the problem but the pedal still hit the switch harder than i liked
1966 F250 4x4
1964 Rambler Ambassador 990
Rest in peace departed Slick family members
Cam Milam
Lesley Ferguson
Steve Lopes
John Sutton
Post Reply