292 cu in Y-block V8 heads

A place for discussion of off topic subjects. Pretty much anything goes - just keep it civil, please!

Moderators: Casey 65, Kid

Post Reply
mercuryv8
Posts: 328
Joined: November 8, 2013, 1:20 am
Location: Edmonton, Alberta
Canada

292 cu in Y-block V8 heads

Post by mercuryv8 »

I'm stuck looking for a set of heads for a 292 cu in in a 55 thunderbird. They are a lot harder to find than you would think. The heads we had have a crack, the head shop we sent them to said they are not repairable.

Any Ideas on where I could get a set?

Nic
User avatar
charliemccraney
Posts: 1743
Joined: July 9, 2008, 10:02 pm
Location: Lawrenceville, GA

Re: 292 cu in Y-block V8 heads

Post by charliemccraney »

In general, y block heads are easy to find. If you want the exact same head, to keep the car "correct," that could be challenging. Try Y-Blocksforever or the Y-Block groups on facebook, eBay or craigslist for local stuff.
Lawrenceville, Ga
1961 F100 Unibody
318 Y-block (292 +.070 bore, +.170 stroke), FMS T5-Z w/Mustang 10.5" diaphragm clutch.
64 f100
Posts: 2754
Joined: July 18, 2006, 7:23 am
Location: Carmi, Illinois, 62821

Re: 292 cu in Y-block V8 heads

Post by 64 f100 »

What heads are you looking for? I have a set of 57 big valve ECG heads , in fact I have a couple of sets. The numbers are on the heads , kind of in an odd spot. All the heads are listed on John Mummerts Yblock site . I have a few other heads and access to others. If, you need the exact heads to make the car right, then that might be a little difficult to come up with, depending on which ones you need. First you have to let us know what the head numbers are that you have. These may not even be the correct ones for that car. Anyway, let me know if you are interested and what heads you have. Just remember, yours were cracked and so may be any you buy. Best to buy and pay for heads from somebody that will guarantee no cracks. I would have to take mine to get checked before I sold these to you. This adds to the cost of the heads, by quite a bit around here. Best to have the heads checked before paying for shipping though. I have 1K tied up in one set of heads I have, because I had to go thru so many heads to find a good set.

Rich
1961 F350
1964 Galaxie convertable
1964 flairside, style side, and longbed
1965 Ranger, and shortbed
1966 long bed, and shortbed
A few parts trucks also
1991 Capri
2011 F250
2004 Lexus
jamesdfo
Posts: 1637
Joined: February 15, 2011, 10:32 am
Location: Edmonton, Alberta
Canada

Re: 292 cu in Y-block V8 heads

Post by jamesdfo »

Nic: Call me, I may know someone, if he doesn't have, he will have leads.....
mercuryv8
Posts: 328
Joined: November 8, 2013, 1:20 am
Location: Edmonton, Alberta
Canada

Re: 292 cu in Y-block V8 heads

Post by mercuryv8 »

Thanks for the replies.

I will get the exact casting numbers and do some more research. Its not a numbers car but I will make certain what's heads will work.

James, I will give you a call when I do that.



Nic
bruceandersson
Posts: 906
Joined: August 12, 2009, 9:44 am
Location: Ohio

Re: 292 cu in Y-block V8 heads

Post by bruceandersson »

The challenge with the early y-block heads is that they came with cast core plugs in the ends that have to be there to look correct on a 55 or 56 tbird. Everything (most) made 57 and on does not have these core plugs. You'll need heads from 54-56 to look right and probably from '55 to have the right casting numbers.
mercuryv8
Posts: 328
Joined: November 8, 2013, 1:20 am
Location: Edmonton, Alberta
Canada

Re: 292 cu in Y-block V8 heads

Post by mercuryv8 »

Thanks for all the replies.

We found a set and they are on their way.

Nic
Post Reply