Pulling a 5.0 out of an 83-91 Grand Marquis/Crown Vic

A place for discussion of off topic subjects. Pretty much anything goes - just keep it civil, please!

Moderators: Casey 65, Kid

Post Reply
User avatar
The Big M
Posts: 1360
Joined: August 9, 2006, 3:03 pm
Location: Rocky View County, AB
Canada

Pulling a 5.0 out of an 83-91 Grand Marquis/Crown Vic

Post by The Big M »

Has anyone ever done this? I'm wondering if I can pull the motor and tranny out together, then disconnect them from each other when the whole works is out of the car. I'd probably have to take the front fascia off the car, but I think that can be done fairly easily.

My reasoning is that it may be easier to access the bellhousing bolts when the motor and tranny are out, rather than struggling to find clearance between the bellhousing and firewall (it's pretty tight in there).

Any thoughts? Is this an easier way to do it, or is it better to unbolt the tranny, pull the motor out, then drop the tranny out the bottom? It's a fuel-injected 5.0 with the dual-sump pan, and the tranny is an AOD.
User avatar
Ford4jack
Posts: 707
Joined: July 22, 2006, 7:56 am
Location: Tennessee

Post by Ford4jack »

Never been there or done that on that model car but I bet it was put in as an assembly at the factory.

Might want to put the wheels up on good solid blocks high enough to get good ground clearance if you try to tip it up & out.

One sure way to find out and if it has to be split at least everything is loose and ready to go.

Remember to drain the transmission :lol: that's what I seem to forget about when tipping oil filled things up. :roll:
Phil
Posts: 2125
Joined: June 1, 2007, 9:37 pm
Location: toledo

Post by Phil »

$4 trans plug has saved me some serious messes.

Id pull it together. I have a 97 5.0/AOD in my garage out of a cougar.
It was pulled together.
Ive never done my 460/C6 in my Torino any other way.
Someday I'll get another slick :(
Image
User avatar
mikecarson
Posts: 596
Joined: July 9, 2006, 5:59 am
Location: Richland, Texas
Contact:

Post by mikecarson »

I did it the hard way, lifted the whole body high enough to roll the engine/tranny out while still attached to the chassis.
Mike C
64 CC, Crown Vic project
62 CC
67short 94 F150, 433W
Life should NOT be a journey to the grave with the intention of arriving safely in an attractive body, but to skid in sideways - body worn out and screaming: Woo Hoo, what a ride!"
User avatar
Greg D
Posts: 10113
Joined: September 13, 2006, 4:39 pm
Location: Podunk Iowa
United States of America

Post by Greg D »

I have never pulled and engine and tranny separately. I sold a wrecked 87 Crn Vic S I had to a guy who pulled the 351 & AOD together while the car was still at my house.
1964 F 100 - I am going to do "something" with it.......

viewtopic.php?f=32&t=15942

1987 Mustang LX Convertible, 2.3 Auto - cruiser.
1994 F 150 XLT 2WD


~ Yes - I adopted another cat..............

Cam L Milan,
You'll be missed my friend.
User avatar
The Big M
Posts: 1360
Joined: August 9, 2006, 3:03 pm
Location: Rocky View County, AB
Canada

Post by The Big M »

Thanks guys. I took another look last night and I think I'll definitely pull both out together. My teardown manual says that the engine and tranny must be removed separately, but I'm not convinced. The rad is out and I took off the fan, so there's plenty of room in front. And the car is up on jackstands, so there's plenty of room underneath.
HeavyHauler wrote:$4 trans plug has saved me some serious messes.
That sounds like a good idea. I was just going to drain it.
User avatar
Slick Fan
Posts: 4085
Joined: November 4, 2006, 5:09 pm
Location: UTAH...snow blows!

Post by Slick Fan »

Those little tranny plugs are lifesavers, for sure...as long as you don't bump it with your foot or something. :oops: :lol:

I have yet to remove an engine & tranny together, I guess I'm sort of a masochist. :shock: I should try it next time & see how I like it, I suppose. :)


As far as how the factory did it, with the Crown Vic's being a full frame car, I'm thinkin' they installed them on the rolling chassis & lowered the body on later.
My "Slickitis" affliction began here...
Image


66 F100 CC/65 F100 CC/66 F250 CC
If it starts to rain, they'll tax the splash.
If you want to fish, they'll tax the bass.
If you plant a yard, they'll tax the grass.
If you don't play nice, they'll fine your *$#!
User avatar
The Big M
Posts: 1360
Joined: August 9, 2006, 3:03 pm
Location: Rocky View County, AB
Canada

Post by The Big M »

Yeah, probably. Now where's my torch? :twisted:
User avatar
The Big M
Posts: 1360
Joined: August 9, 2006, 3:03 pm
Location: Rocky View County, AB
Canada

Post by The Big M »

I did a quick web search but couldn't find a trans plug anywhere. Where do you guys get them? It's a bit of a moot point now, as I already drained the trans last night, without spilling on the driveway, no less! Hooray for cardboard!

Should I keep fluid in the trans to store it? I won't be putting it in anything for some time, since the 5.0 needs a rebuild.

Also, are the trans crossmembers in these cars useful for anything? I've heard of using the earlier LTD crossmember in our trucks, but are these any different?

Anyway, with any luck the motor and trans will be out of the car tonight. I still need to unbolt the crossmember, disconnect the exhaust, and unplug the wiring harness. Then it's off to the races!
User avatar
Fanatic
Posts: 1568
Joined: July 14, 2006, 11:39 pm
Location: Leesport, PA

Post by Fanatic »

Back in the day I put a piece of inner tube (remember those) around the end and a hose clamp.
The other option is to have your helper be the DOWN man---while YOU work the hoist!
INEPTOCRACY: (in-ep'-toc-ra-cy) : a system of government where the least capable to lead are elected by the least capable of producing, and where the members of society least likely to sustain themselves or succeed are rewarded with goods and services paid for by the confiscated wealth of a diminishing number of producers.
User avatar
The Big M
Posts: 1360
Joined: August 9, 2006, 3:03 pm
Location: Rocky View County, AB
Canada

Post by The Big M »

Inner tube, great idea! I wish I would have thought of that. As it turns out I didn't manage to drain all the trans fluid until the motor was tilted up. I also didn't get all the coolant drained out of the block either. Oh well...

I did manage to extract the motor and trans together, without a helper and without unbolting the crossmember. The only problem was the exhaust. I tried to get it out with everything ahead of the y-pipe still connected to the manifolds. It worked out alright, except for the little crossover pipe connecting the driver and passenger side catalytic converters. It didn't survive... :lol:
Post Reply