223 -> 300 distributor swap question
223 -> 300 distributor swap question
I'm considering swapping my 223 loadomatic distributor to one from a 300 and I am wondering how much work will be involved. I pulled my loadomatic distributor today to see if it was a 1/4" or 5/16" shaft. It's a 5/16" so I don't think I would have to mill or modify the 300 distributor shaft. I'm guessing I might have to cut it down a little but that's not a big deal. My question is: will I still have to change the 223 gear over or will the stock 300 gear be ok? I've read several of the tech posts but they all address the older 223 with the 1/4" drive fuel pump.
- bobenhotep
- Posts: 911
- Joined: January 9, 2007, 4:15 am
- Location: Las Cruces, NM
- Contact:

Re: 223 -> 300 distributor swap question
If you have the 5/16 inch oil pump drive the gear off of the distributor will have to be swapped, but it should fit on the 300 distributor without having to machine/ file/ drill anything. Way easier than if you have a 63 or earlier 223.
Dan
Dan
For every person with a spark of genius, there are a hundred with ignition trouble
My '63 short wrongbed
"The Iron Rhino"
300 I6, 3 spd manual, DS II/ HEI ignition.
Stuff I added to Hints and tricks
-300-6 choke tube repair
-duraspark II/ HEI
-Horn ring contact tube repair
-turn signal indicator fix
Mikhail Kalashnikov and Nikola Tesla are the guys i think of when i build things.

My '63 short wrongbed
"The Iron Rhino"
300 I6, 3 spd manual, DS II/ HEI ignition.
Stuff I added to Hints and tricks
-300-6 choke tube repair
-duraspark II/ HEI
-Horn ring contact tube repair
-turn signal indicator fix
Mikhail Kalashnikov and Nikola Tesla are the guys i think of when i build things.

- ezernut9mm
- Posts: 9141
- Joined: July 21, 2006, 9:37 pm
- Location: KCMO

Re: 223 -> 300 distributor swap question
I have a Mallory unilite for a 223 I'll sell ya real cheap. 
always
"i believe i've achieved satisfaction".-bubbles
"should i be gettin" baked for this boys?"-bubbles
i could no longer keep "r.i.p.ing" all of our fallen brothers and sisters, so i say here, slick loads of love and much respect to all you beautiful people.
"i believe i've achieved satisfaction".-bubbles
"should i be gettin" baked for this boys?"-bubbles
i could no longer keep "r.i.p.ing" all of our fallen brothers and sisters, so i say here, slick loads of love and much respect to all you beautiful people.
Re: 223 -> 300 distributor swap question
Thanks for the info. I was planning on swapping to the 300 and installing a pertronix in it at the same time. I'm not super familiar with the Mallory stuff. Seems like that requires an ignition box doesn't it? Thanks again
- ezernut9mm
- Posts: 9141
- Joined: July 21, 2006, 9:37 pm
- Location: KCMO

Re: 223 -> 300 distributor swap question
i was kinda smartassing, keep on going in the direction you are going. its a better one. lol
always
"i believe i've achieved satisfaction".-bubbles
"should i be gettin" baked for this boys?"-bubbles
i could no longer keep "r.i.p.ing" all of our fallen brothers and sisters, so i say here, slick loads of love and much respect to all you beautiful people.
"i believe i've achieved satisfaction".-bubbles
"should i be gettin" baked for this boys?"-bubbles
i could no longer keep "r.i.p.ing" all of our fallen brothers and sisters, so i say here, slick loads of love and much respect to all you beautiful people.
