T5 question I can't find an answer for
T5 question I can't find an answer for
I've been searching off and on for a week now trying to find out if I can use an s10 nwc trans with the mechanical speedo (which I already have on the floor of my dads garage collecting dust) to compliment my f100 with a 223. From what I've learned I have the same bell as a y-block and there are adapters for y-blocks to mustang t5's, and I could use the s10 tailshaft on a nwc mustang t5, but I can't find an adapter for the s10 t5 to ford 223 mounting. I realize mustang t5's aren't hard to come by, but since I already have the s10 t5 with a clutch kit and no plans to use it elsewhere I figured it was worth a shot. Thanks
-
SteveCanup
- Posts: 1096
- Joined: November 7, 2014, 11:08 pm
- Location: Wytheville, Virginia

- unibody madness
- Posts: 2147
- Joined: December 4, 2008, 4:33 pm
- Location: Paradise,CALIFORNIA 95969

Re: T5 question I can't find an answer for
I know I have used the s10 tail shaft housing with a ford t-5.
I have also used the t-5 s10 tail shaft and housing to match the ford t-5, all you need is the overdrive gear, there is a guy on the east coast that I bought mine from.
I do not know if the s-10 tranny will bolt up to the ford bell.
By the way you will need the three speed bell for whatever motor you have in order for the bell adaption to work, I have not heard of a four speed adapter.
john
I have also used the t-5 s10 tail shaft and housing to match the ford t-5, all you need is the overdrive gear, there is a guy on the east coast that I bought mine from.
I do not know if the s-10 tranny will bolt up to the ford bell.
By the way you will need the three speed bell for whatever motor you have in order for the bell adaption to work, I have not heard of a four speed adapter.
john
Turk build thread at:
http://slick60s.com/viewtopic.php?f=32&t=18944
It does not matter what you think, it only matters what you do about it!
http://slick60s.com/viewtopic.php?f=32&t=18944
It does not matter what you think, it only matters what you do about it!
Re: T5 question I can't find an answer for
This might help some...
I know the T5 has been bolted to a 223...
The 223 and 292 do NOT use the same bell pattern...
I found out the hard way !
viewtopic.php?f=1&t=18811&p=161958&hili ... 23#p161958
I know the T5 has been bolted to a 223...
The 223 and 292 do NOT use the same bell pattern...
I found out the hard way !
viewtopic.php?f=1&t=18811&p=161958&hili ... 23#p161958
.
.
.
'' I think what scares me the most about you guys is that I understand you '' ..... KID
'' lookin good, a little paint adds at least 100hp!'' ....... COOTER
'' well an old guy can dream cant he? ''............ICEMAN
''I would donate organs before selling my slick''........ HOOFBEAT RACER
.
.
'' I think what scares me the most about you guys is that I understand you '' ..... KID
'' lookin good, a little paint adds at least 100hp!'' ....... COOTER
'' well an old guy can dream cant he? ''............ICEMAN
''I would donate organs before selling my slick''........ HOOFBEAT RACER
Re: T5 question I can't find an answer for
Well that's good to know. I think I read on h.a.m.b. that The 223 and y-block used the same bellhousing. I emailed John Mummert and Modern Driveline to see if they know something I can't find online. I may also hit up wilcap while I'm in the typing mood. I'm not above taking the bellhousing to a machine shop to have it drilled for the t5. I don't know if that's a viable option or not though. I would really like to use my original bellhousing and clutch pedal linkage. I've tried mounting clutch master/slave cylinders with other cars and never had much luck fabricating the brackets. I've been looking for a t5 on Craigslist (Nashville tn area) but haven't had much luck. Seems they're not as easy to find as I expected, at least not under $300. Thanks again for the advice.
- unibody madness
- Posts: 2147
- Joined: December 4, 2008, 4:33 pm
- Location: Paradise,CALIFORNIA 95969

Re: T5 question I can't find an answer for
Mummert will adapt the three speed bell for either 223 or 292 block, he did one of each for me, but it must be the three speed bell for that motor.
Turk build thread at:
http://slick60s.com/viewtopic.php?f=32&t=18944
It does not matter what you think, it only matters what you do about it!
http://slick60s.com/viewtopic.php?f=32&t=18944
It does not matter what you think, it only matters what you do about it!
- charliemccraney
- Posts: 1743
- Joined: July 9, 2008, 10:02 pm
- Location: Lawrenceville, GA
Re: T5 question I can't find an answer for
The block bolt pattern is the significant difference between a 223 and Y-Block bellhousing. The depth, and transmission pattern will be the same. Because of the bellhousing depth, an adapter cannot be used. The bellhousing has to be modified and the transmission bolts directly to it. You'll need to trim about 3/32" from the input shaft pilot.
Since the bellhousing has to be modified, you may be able to make the S10 transmission work. It will probably be easiest to check with some local fab shops. But before you do anything, make sure the input shaft will be long enough.
Regarding a hyrdraulic clutch, Y-block truck bellhousings from 1957 on have a mount ear for a slave cylinder. If the 223 was the same, then a hydraulic clutch is nearly a bolt on if you can find an original master cylinder.
Since the bellhousing has to be modified, you may be able to make the S10 transmission work. It will probably be easiest to check with some local fab shops. But before you do anything, make sure the input shaft will be long enough.
Regarding a hyrdraulic clutch, Y-block truck bellhousings from 1957 on have a mount ear for a slave cylinder. If the 223 was the same, then a hydraulic clutch is nearly a bolt on if you can find an original master cylinder.
Lawrenceville, Ga
1961 F100 Unibody
318 Y-block (292 +.070 bore, +.170 stroke), FMS T5-Z w/Mustang 10.5" diaphragm clutch.
1961 F100 Unibody
318 Y-block (292 +.070 bore, +.170 stroke), FMS T5-Z w/Mustang 10.5" diaphragm clutch.


