Some time back, I decided to tear down the 351w for my grandsons truck. Somewhere along the line I ran across and add for a 69 block and thought that would be a better choice for rebuilding. Very rusty but stock bore. Took it to the machine shop and had it bored cleaned and deck trued. Total came to a whopping 650 for the work. which I thought was very high. Got the block home and started installing cam bearings and cam. When done with that I decided to install the crank. This is when I ran into trouble. Crank went in fine but when I installed the number 3 center thrust bearing the crank locked in place. Thought maybe the crank was bent so installed a different crank with a little wear with the thought that the looser crank might help. No go. Noticed no end play on crank even when only slightly tightened center main bearing bolts. Took all the other main bearings off pulled the center on down and it locked the crank again . I had plastigaged the bearings when I installed the new bearings and had noticed the center being tight.
After loosening and tightening the center cap I notice it walked to the side and thrust bearing showed impression on bottom of one side and to of other. Got suspicious and took the cap off and put a square to it. Some jackass in the past had apparently done some shade tree grinding of the caps ends where it fit the block. It was about 1/32 off from one side to the other causing the bearing to kick to one side. Please bear in mind, I already have roughly 800$ in this block and now have a daytime nightmare. Because the Chinese were buying all our scrap at high prices, every scrap block in the country went to china which makes it nearly impossible to find a cap that will fit close enough to be align honed to fit. I have gotten two , one of which will fit fairly well if I turn it backwards. Otherwise it will have to be lined bored if there is to much that has to be removed, or I would go with four bolt caps. Not having any experience with installing 4 bolt caps, wondering if it is better to get straight four bolt caps or go with ones that have the outer bolts at an angle. I'm thinking at angle are best , but most likely will require being drilled in a machine shop. Some of the caps I've seen come with and drill sleeve but only on straight in bolts.
Since I've already spent a fortune on this block, I have decided to put it aside and bore a 74 block for my grandson, which I what I should have done to start with. I will think on what I will do with the 69 block. 4 bolt mains and a stroker kit may be in it's future, although I've heard there is a problem with stoking one of the early blocks. Anyone have insight on that?
Nightmares in the daytime.
Re: Nightmares in the daytime.
Rich, we are working on Dale's daily driver, which appears to have broken the crank. No problem, 351's trump 302's in our opinions at least!
Long story, here goes!
Not unlike our foreign competitors (and that's what they are!); I have also bought up a bunch of American iron! 351's and 460's are my forte, along with, um, a few assorted slicks!
I had traded some years ago for a marine 351, supposedly just built. The owner had decided to go with a 385 in his boat. After I had added it to my inventory; one of his partners asked what I was going to do with it. I said I would probably eventually use it for the basis of a stroker. He proceeded to show me an obviously well-built 393 short block, so it also followed me home.
Both have set in my engine conex ever since, with the plan of upgrading my full size Bronco once it is emissions exempt.
So, when Dale started talking stroker (whodda thunk!), I thought the marine engine would make an excellent base. Popped the marine manifold off to find a pristine engine with the assembly lube still in place, and obvious signs it was straight from Ford! After further examination with a bore scope, we decided it was too good an engine to use just for the block. Grabbed another engine from the stack, dissassembled and sent to Houston Engine Balancing. No good, core shift! Another try, similar results. Another buddy had a late model block, Dale purchased it; sent it to the shop, and we are awaiting results!
IMO, another factor, in addition to the years out of production, is that anyone looking for an easy Fox body upgrade, is going to at least consider the 351.
Late Model Restoration listed a new 351 based 427 short block delivered, for around $5000.00; out of stock, with no firm idea if or when it might again be available.
Obviously, I have plenty of main caps, they are yours if you want. More than likely, as you know, line boring will still be required.
Paul
Long story, here goes!
Not unlike our foreign competitors (and that's what they are!); I have also bought up a bunch of American iron! 351's and 460's are my forte, along with, um, a few assorted slicks!
I had traded some years ago for a marine 351, supposedly just built. The owner had decided to go with a 385 in his boat. After I had added it to my inventory; one of his partners asked what I was going to do with it. I said I would probably eventually use it for the basis of a stroker. He proceeded to show me an obviously well-built 393 short block, so it also followed me home.
Both have set in my engine conex ever since, with the plan of upgrading my full size Bronco once it is emissions exempt.
So, when Dale started talking stroker (whodda thunk!), I thought the marine engine would make an excellent base. Popped the marine manifold off to find a pristine engine with the assembly lube still in place, and obvious signs it was straight from Ford! After further examination with a bore scope, we decided it was too good an engine to use just for the block. Grabbed another engine from the stack, dissassembled and sent to Houston Engine Balancing. No good, core shift! Another try, similar results. Another buddy had a late model block, Dale purchased it; sent it to the shop, and we are awaiting results!
IMO, another factor, in addition to the years out of production, is that anyone looking for an easy Fox body upgrade, is going to at least consider the 351.
Late Model Restoration listed a new 351 based 427 short block delivered, for around $5000.00; out of stock, with no firm idea if or when it might again be available.
Obviously, I have plenty of main caps, they are yours if you want. More than likely, as you know, line boring will still be required.
Paul
The Ford Orphanage
Life's too short for boring vehicles!
My quest to develop a universal solvent is held up by the lack of a storage container.
Paul
Life's too short for boring vehicles!
My quest to develop a universal solvent is held up by the lack of a storage container.
Paul
Re: Nightmares in the daytime.
The guy I'm using is a one man shop and all he has is a honing setup. Most likely, I will have to inquire around, Nothing closer than 30 miles. That's the guy I use. I have one cap that comes real close if I turn it around backwards. The other one is pretty decent but doesn't fit as well as the one I turned around backwards. If, I have to have it line bored, what is the usual cost for this? I've never had one done before. Have you used the 4 bolt main caps, and which do you consider better? Truthfully, just installing those should bring the value up on the block, but frankly I've seen man o war blocks for 2,000, so where do I call it quits? I was just building two mild torque engines for a couple of trucks. Makes me wonder how I got trapped into this nightmare. Never mind, I know how. Could not resist the C9 block, thought if I was going to build the young man an engine, why not that block. I may take you up on some of those caps, I would gladly pay shipping both ways and make sure you got back as many as you sent. Thank you for offering. While your at it, just send along that new motor you have , I would be pleased to get it out from under your feet, and I would send it back ready for that stroker kit.
Rich
Rich
1961 F350
1964 Galaxie convertable
1964 flairside, style side, and longbed
1965 Ranger, and shortbed
1966 long bed, and shortbed
A few parts trucks also
1991 Capri
2011 F250
2004 Lexus
1964 Galaxie convertable
1964 flairside, style side, and longbed
1965 Ranger, and shortbed
1966 long bed, and shortbed
A few parts trucks also
1991 Capri
2011 F250
2004 Lexus
Re: Nightmares in the daytime.
I'm going with 4 bolt main caps and have found someone to do the main bearing boring. What's another 3 or 4 hundred matter to a grandfather. Really had not intended to get race engine money involved in a rebuild. Life is growing to short at my age to get involved in this kind of snafu.
Rich
Rich
1961 F350
1964 Galaxie convertable
1964 flairside, style side, and longbed
1965 Ranger, and shortbed
1966 long bed, and shortbed
A few parts trucks also
1991 Capri
2011 F250
2004 Lexus
1964 Galaxie convertable
1964 flairside, style side, and longbed
1965 Ranger, and shortbed
1966 long bed, and shortbed
A few parts trucks also
1991 Capri
2011 F250
2004 Lexus
Re: Nightmares in the daytime.
Wow, what is the cost for the four bolt mains and associated machining? You are correct, you are pushing close to my cost for a fresh Dart block; but I'm well aware that sometimes things go that way! Still haven't heard from the machine shop; something about having to replace a sonic test apparatus!
Paul
Paul
The Ford Orphanage
Life's too short for boring vehicles!
My quest to develop a universal solvent is held up by the lack of a storage container.
Paul
Life's too short for boring vehicles!
My quest to develop a universal solvent is held up by the lack of a storage container.
Paul

