effect of altitude on specifications

The place to talk Slicks. All we ask is that discussion has something to do with slicks...

Moderators: Casey 65, Kid

Post Reply
ICEMAN6166
Posts: 11470
Joined: July 11, 2006, 11:28 am
Location: Dove Creek, Co. elevation 6842
Poland

effect of altitude on specifications

Post by ICEMAN6166 »

in the ford factory manuals the specs for vacuum and compression are listed as being taken @ sea level

what effect does being a mile and a half above have on them
obviously as you go up the air is thinner, this is commmon knowledge and carbs are adjusted accordingly

will my actual readings be more or less than the specs and how will this translate to be correct or good

pretty sure the vac reading will be lower than the 17-18 in the manual

compression i have always understood is not the max value but the consistency between cylinders unless they are all very low
1966 F250 4x4
1964 Rambler Ambassador 990
Rest in peace departed Slick family members
Cam Milam
Lesley Ferguson
Steve Lopes
John Sutton
User avatar
The Big M
Posts: 1360
Joined: August 9, 2006, 3:03 pm
Location: Rocky View County, AB
Canada

Re: effect of altitude on specifications

Post by The Big M »

I would think both would be below the published numbers. I know there's a rule of thumb for octane rating where you can reduce it x number of points per a certain increase in elevation.

Found this regarding vacuum:
NOTE: Vacuum readings will vary according to the altitude in different localities. From sea level to 2,000 feet elevation all normal engines should show a vacuum reading between 17 to 21 inches. Above 2,000 feet elevation the vacuum reading will be about one (1) inch lower per each 1,000 feet rise in elevation.
http://www.gregsengine.com/using-a-vacuum-gauge.html

This makes sense considering the vacuum gauge will also be reading a number relative to atmospheric pressure, which as you've stated is much lower at altitude. So the engine could be pulling the same absolute level of vacuum, but the will read lower since your reference pressure is much lower than at sea level.

Similarly for compression, the gauge is also reading relative to atmospheric. The engine can only squish the fuel/air mixture so much, and since you're starting at a lower pressure the max will be reduced at altitude. Also I think the volumetric efficiency of your engine will be be reduced, which effects compression. That is, lower atmospheric pressures (i.e thinner air) will make it tougher to fill the cylinder, so a naturally aspirated engine won't make the same amount of horsepower at altitude as it will at sea level.
BarnieTrk
Posts: 1448
Joined: July 11, 2007, 2:37 pm
Location: Stanton, Michigan

Re: effect of altitude on specifications

Post by BarnieTrk »

Good question, Brian. I guess I hadn't considered those readings as being variables. oops.gif

Good info, Big M! Thanks for sharing..... :cheers:

BarnieTrk :steering:
User avatar
Toyz
Posts: 4334
Joined: March 22, 2011, 6:23 pm
Location: Baja Houston Taxes
United States of America

Re: effect of altitude on specifications

Post by Toyz »

At 7500 elevation your correction factor will be roughly .75, so indicated compression of 160 would equal about indicated 120 at 7500 ft. elevation.

Paul
The Ford Orphanage
Life's too short for boring vehicles!
My quest to develop a universal solvent is held up by the lack of a storage container.
Paul
ICEMAN6166
Posts: 11470
Joined: July 11, 2006, 11:28 am
Location: Dove Creek, Co. elevation 6842
Poland

Re: effect of altitude on specifications

Post by ICEMAN6166 »

this all makes sense to me and goes along fairly close to the actual readings i got

manual states 17-18 as normal vac for 292, mine reads 14 at idle

similarly the compression of 110-120 falls in line too

thanks for helping clarify this
1966 F250 4x4
1964 Rambler Ambassador 990
Rest in peace departed Slick family members
Cam Milam
Lesley Ferguson
Steve Lopes
John Sutton
64 f100
Posts: 2754
Joined: July 18, 2006, 7:23 am
Location: Carmi, Illinois, 62821

Re: effect of altitude on specifications

Post by 64 f100 »

Ice, I don't think your engine will have 160 for compression even if it were new and broken in. Truck engines were of a lower number and although rated at 8.8 to 1 in may or may not have achieved 120 under normal operating conditions. Unless the heads have been changed for high compression I would question the 160 number at sea level. According to my motors manual horsepower dropped from 1958 to 1062 by 300HP. What caused this I cannot say. This was like I said a motors repair manual, and did not list actual compression numbers. For some reason my green 64 repair manual is not here where it should be. So the only source I have for reference is the motors book. As to the affect on a compression gauge of altitude, I don't know. That being said, The compression gauge would be spring loaded or such and not affected, I think, by altitude. If the gauge was affected at all I would think the opposite would be true. Less pressure outside would mean more pressure from cylinder? More likely it's a matter of less density to the air which may cause the compression drop. I'm sure there are articles that will refute my idea for what is, or is not on this. I do think there were modifications to some of Fords heads for higher altitude in slightly larger head chambers. I've heard of these heads as, Denver heads in relation to this. I do remember checking compression on my friends 50 Ford flathead just south of Denver at Castle Rock, and it had 70 lbs on one cylinder and around 50 on the rest.

Rich
User avatar
Toyz
Posts: 4334
Joined: March 22, 2011, 6:23 pm
Location: Baja Houston Taxes
United States of America

Re: effect of altitude on specifications

Post by Toyz »

The MD 292 was rated at 7.9 to 1 compression. Volumetric efficiency would dictate the engine would likely NOT have "120 under normal operating conditions". As far as testing, given "by the book" procedure, engine thoroughly warm, throttle completely open; 150 to 160 would not come as a surprise here at sea level. Not sure of that 300 horsepower drop; a comparison of "net horsepower", as well as rated compression ratio for the MD 292 indicates no change. Since it's a given that both vacuum and compression will be lower at vastly higher altitudes; I see no benefit to "larger combustion chambers" as related to altitude. Seems to me that would be a step in the wrong direction. Full disclaimer: I have done very little actual engine diagnosis at mile-high + altitudes, I hear it can get COLD under those conditions! I DO have faith in proven mechanical formulas, however; I probably have a poor understanding of them, but I tend to believe them.
Paul
The Ford Orphanage
Life's too short for boring vehicles!
My quest to develop a universal solvent is held up by the lack of a storage container.
Paul
ICEMAN6166
Posts: 11470
Joined: July 11, 2006, 11:28 am
Location: Dove Creek, Co. elevation 6842
Poland

Re: effect of altitude on specifications

Post by ICEMAN6166 »

i should mention my compression test was done cold, no spark plugs in any cylinders nor exhaust manifolds in place
the intake and carb were on.
i was really looking to see if #6 the ugly cylinder was drastically lower than the rest, it was not so that settled my worry a lot.
Toyz wrote: Full disclaimer: I have done very little actual engine diagnosis at mile-high + altitudes, I hear it can get COLD under those conditions!
Paul
it does occasionally get cold here but not like my former home and not for long periods of time.my actual experience is its much easier diagnosing mechanics here than in outdoor winter Alaska.
1966 F250 4x4
1964 Rambler Ambassador 990
Rest in peace departed Slick family members
Cam Milam
Lesley Ferguson
Steve Lopes
John Sutton
User avatar
Toyz
Posts: 4334
Joined: March 22, 2011, 6:23 pm
Location: Baja Houston Taxes
United States of America

Re: effect of altitude on specifications

Post by Toyz »

ICEMAN6166 wrote:i should mention my compression test was done cold, no spark plugs in any cylinders nor exhaust manifolds in place
the intake and carb were on.
i was really looking to see if #6 the ugly cylinder was drastically lower than the rest, it was not so that settled my worry a lot.
Toyz wrote: Full disclaimer: I have done very little actual engine diagnosis at mile-high + altitudes, I hear it can get COLD under those conditions!
Paul
it does occasionally get cold here but not like my former home and not for long periods of time.my actual experience is its much easier diagnosing mechanics here than in outdoor winter Alaska.
Not for me; in either situation, I would definitely continue to specialize in "diagnosis via internet"! :twisted:
Paul
The Ford Orphanage
Life's too short for boring vehicles!
My quest to develop a universal solvent is held up by the lack of a storage container.
Paul
BarnieTrk
Posts: 1448
Joined: July 11, 2007, 2:37 pm
Location: Stanton, Michigan

Re: effect of altitude on specifications

Post by BarnieTrk »

As a side note in considering altitude - what does a fella have to do to his tunup settings if traveling from say, 600ft to 4700ft elevation?

BarnieTrk
User avatar
Toyz
Posts: 4334
Joined: March 22, 2011, 6:23 pm
Location: Baja Houston Taxes
United States of America

Re: effect of altitude on specifications

Post by Toyz »

Put your foot in it harder! My experience is:"nothing!" Mixture is going to be a little richer, you might be able to add a little timing and lean the mixture somewhat, but I never bothered. It's also been a heck of a long time since I have varied the altitude that much in a "non-feedback" engine.
Paul
The Ford Orphanage
Life's too short for boring vehicles!
My quest to develop a universal solvent is held up by the lack of a storage container.
Paul
BarnieTrk
Posts: 1448
Joined: July 11, 2007, 2:37 pm
Location: Stanton, Michigan

Re: effect of altitude on specifications

Post by BarnieTrk »

Thanks, Paul.
So, I guess that would mean that I should expect fuel mileage to drop off a tad if I was not to monkey with the 'sea level' tune, correct?

BarnieTrk
User avatar
Toyz
Posts: 4334
Joined: March 22, 2011, 6:23 pm
Location: Baja Houston Taxes
United States of America

Re: effect of altitude on specifications

Post by Toyz »

You moved that well over my weak head quickly!
There is theory and there are real life factors to consider. "IF" your sea level tune were spot on, you would possibly see a decline in fuel economy, since it may take more throttle opening to achieve the same level of performance.
As obvious from my affinity for the Turbofords and slicks; it is probably obvious I am what's known as "cheap"! Thus, when the differential between super premium and regular becomes as skewed as it has been lately, my frugal nature has me running regular in my daily drivers meant for premium fuel. The results of that, IME, is that my non-computer vehicles seem to run a little better and seem a very slight bit more fuel efficient at (reasonable) altitudes. The computer cars seem to see a more pronounced, although still negligible gain, attributable to the 'puter doing it's job and allowing more spark advance, and possibly LESS fuel to maintain an approximation of Lambda.
Just my thoughts and limited experiences; I may have missed reality by a mile!
Paul
The Ford Orphanage
Life's too short for boring vehicles!
My quest to develop a universal solvent is held up by the lack of a storage container.
Paul
ICEMAN6166
Posts: 11470
Joined: July 11, 2006, 11:28 am
Location: Dove Creek, Co. elevation 6842
Poland

Re: effect of altitude on specifications

Post by ICEMAN6166 »

if you look thru ford or other makers carb specs there is a list that tells the correct main jet level for different elevations
mostly the number is one or two below the stock jet
i have not messed with them since coming up to the 7000 ft. level , in fact i have been above 10k on several occasions in the y block powered slick and with the 4.56 the 11-12 mpgs are no different than the sea level to 1k roads in Alaska

yesterdAy on the 100 + mile ride i paid close attention to the vac gauge
stomp the foot down climbing a hill vac is down to 5 hg or a bit less, coast downhill,@ 75 mph it will nearly hit 20
1966 F250 4x4
1964 Rambler Ambassador 990
Rest in peace departed Slick family members
Cam Milam
Lesley Ferguson
Steve Lopes
John Sutton
BarnieTrk
Posts: 1448
Joined: July 11, 2007, 2:37 pm
Location: Stanton, Michigan

Re: effect of altitude on specifications

Post by BarnieTrk »

Thanks, Paul and Brian, for your experience and knowledge!

I was only wondering because I am looking at a job in Peublo, Colorado. If I get the Pueblo job, I'd likely be taking my 390-powered Slick there. Thus, I was wondering just how much change to it's current performance as I would be leaving the 900 ft elevation here in Mid-Michigan to close to 4700 ft in Pueblo. Based on you guys, it sounds like it the ol' 390 would hardly notice the change........ which probably would be a minor concern in the big picture regarding making such a move for us.

BarnieTrk
User avatar
Toyz
Posts: 4334
Joined: March 22, 2011, 6:23 pm
Location: Baja Houston Taxes
United States of America

Re: effect of altitude on specifications

Post by Toyz »

Not knocking your home state, but all else being equal, job and pay wise, I could DRAG a slick from MI to Pueblo. I agree with Brian, if you have a decent gear, (you'll need it in CO), you are likely to notice little difference! In my case, 460, C6, 3.55s; I would be overjoyed to see double digit fuel economy at sea level, let alone a mile above! For a long-term situation, you could invest in a wide-band meter and tweak as needed, or, although Brian would likely disagree, put a throttle body EFI on and let it do the tuning! The EFI is just unbeatable for varying elevations without hands-on changes. They are also becoming more economical; this quarter's LMC catalog has a setup to control both spark and fuel for under a grand, which means SOMEONE is likely selling it for 3/4 of that price point! Again, :2cents: , it would take a bunch of miles to justify the cost based on fuel savings; but if that were our only interest, we probably would not be driving slicks anyway!

Paul
The Ford Orphanage
Life's too short for boring vehicles!
My quest to develop a universal solvent is held up by the lack of a storage container.
Paul
User avatar
MY OL 66
Posts: 223
Joined: January 16, 2009, 9:53 pm
Location: Tucson, AZ
United States of America

Re: effect of altitude on specifications

Post by MY OL 66 »

Toyz wrote:put a throttle body EFI on and let it do the tuning! The EFI is just unbeatable for varying elevations without hands-on changes. They are also becoming more economical; this quarter's LMC catalog has a setup to control both spark and fuel for under a grand, which means SOMEONE is likely selling it for 3/4 of that price point! Again, :2cents: , it would take a bunch of miles to justify the cost based on fuel savings; but if that were our only interest, we probably would not be driving slicks anyway!

Paul
I was just looking through the online LMC catalog and did not find any references to any EFI setups.

Where exactly did you see this???

Thank you.
Steve F
1965 Mustang Coupe
1966 F-100 Shortbed CC/Ranger
2010 Mustang GT Convertible
2010 Shelby GT500 Convertible
BarnieTrk
Posts: 1448
Joined: July 11, 2007, 2:37 pm
Location: Stanton, Michigan

Re: effect of altitude on specifications

Post by BarnieTrk »

Toyz wrote:Not knocking your home state, but all else being equal, job and pay wise, I could DRAG a slick from MI to Pueblo. - Paul
Ok, Paul..... I get a feeling that there may be a story behind your comment above..... spill it, dude.... :P

BarnieTrk 8)
User avatar
Toyz
Posts: 4334
Joined: March 22, 2011, 6:23 pm
Location: Baja Houston Taxes
United States of America

Re: effect of altitude on specifications

Post by Toyz »

Naw, not really, in a former life, I DID drive a C600 with trailer to the UP. It's just that if I'm going to freeze my arse off, I prefer to do it surrounded by some of the nicest scenery imaginable, next to Texas, that is!
It's on the back cover of the latest LMC catalogue, ( the one with our buddy, McTim on the cover), so probably not listed on their website yet. Base part number is 38-4512, but that doesn't yield results on an online search, either.
Paul
The Ford Orphanage
Life's too short for boring vehicles!
My quest to develop a universal solvent is held up by the lack of a storage container.
Paul
Post Reply