1966 F250 Cummins gauges
- Blackwaterforge
- Posts: 893
- Joined: March 13, 2008, 9:22 am
- Location: Alabama
- Contact:

1966 F250 Cummins gauges
If it cain't be fixed with a sledge hammer it must be an electrical problem!
Re: 1966 F250 Cummins gauges
That's looking very cool.
I like that anvil shifter knob. Undoubtedly you made that!
Bradshaw
I like that anvil shifter knob. Undoubtedly you made that!
Bradshaw
Always know where you will be, when you get where you're going - Jerry Clower
- Blackwaterforge
- Posts: 893
- Joined: March 13, 2008, 9:22 am
- Location: Alabama
- Contact:

Re: 1966 F250 Cummins gauges
Thank you!9Fingers wrote:That's looking very cool.
I like that anvil shifter knob. Undoubtedly you forget that!
Bradshaw
Shifter knob was cast at Lawler foundry in Birmingham in 1933.
That is the year that Vulcan was entered in the Worlds fair.
If it cain't be fixed with a sledge hammer it must be an electrical problem!
Re: 1966 F250 Cummins gauges
I'm not familiar with this custom cab dash insert. What are the two small lamps between the speedometer cluster and each of the two side gauges? Are they turn signal indicators?
Always know where you will be, when you get where you're going - Jerry Clower
- Blackwaterforge
- Posts: 893
- Joined: March 13, 2008, 9:22 am
- Location: Alabama
- Contact:

Re: 1966 F250 Cummins gauges
The dash is from a F800.
I added the lights.
One for oil pressure the other for alternator
I added the lights.
One for oil pressure the other for alternator
If it cain't be fixed with a sledge hammer it must be an electrical problem!
- FarmMotorSports
- Posts: 451
- Joined: November 13, 2010, 6:55 pm
- Location: KS, Lawrence

Re: 1966 F250 Cummins gauges
Which tach are you using, and how is it driven? The originals are cable driven, didn't like the idea of using a factory drive off the front of the cam...
61 F250 Unibody
5.9 Ford Diesel / Allison auto
& 4WD
5.9 Ford Diesel / Allison auto
& 4WD
- Blackwaterforge
- Posts: 893
- Joined: March 13, 2008, 9:22 am
- Location: Alabama
- Contact:

Re: 1966 F250 Cummins gauges
Tach is electric from gas engine.FarmMotorSports wrote:Which tach are you using, and how is it driven? The originals are cable driven, didn't like the idea of using a factory drive off the front of the cam...
Driven by a Dakota digital drive.
Is there a better way to drive it?
If it cain't be fixed with a sledge hammer it must be an electrical problem!
- FarmMotorSports
- Posts: 451
- Joined: November 13, 2010, 6:55 pm
- Location: KS, Lawrence

Re: 1966 F250 Cummins gauges
I don't think there is a better way.... for an electronic tach.
My dash came with a mechanical tach, that I hope to convert to electric.
There is a mechanical tach drive kit made by cummins.
It takes the place of the timing cover plug/ oil fill. It consists of a tang drive that attaches to the cam gear. A threaded cable connector that fills the cover plug and a right angle drive. $$$ in cummins parts...
I'm using a alternator, electronic pulse driven tach to convert the old gauge face and case. If I ever actually do that project. About a $30 investment...
My dash came with a mechanical tach, that I hope to convert to electric.
There is a mechanical tach drive kit made by cummins.
It takes the place of the timing cover plug/ oil fill. It consists of a tang drive that attaches to the cam gear. A threaded cable connector that fills the cover plug and a right angle drive. $$$ in cummins parts...
I'm using a alternator, electronic pulse driven tach to convert the old gauge face and case. If I ever actually do that project. About a $30 investment...
61 F250 Unibody
5.9 Ford Diesel / Allison auto
& 4WD
5.9 Ford Diesel / Allison auto
& 4WD
- Blackwaterforge
- Posts: 893
- Joined: March 13, 2008, 9:22 am
- Location: Alabama
- Contact:

Re: 1966 F250 Cummins gauges
Tach is right at idle.
Should I adjust Dakota digital box til it is right at 2000 rpms and not worry about idle
Should I adjust Dakota digital box til it is right at 2000 rpms and not worry about idle
If it cain't be fixed with a sledge hammer it must be an electrical problem!
- FarmMotorSports
- Posts: 451
- Joined: November 13, 2010, 6:55 pm
- Location: KS, Lawrence

Re: 1966 F250 Cummins gauges
Actually I would want it accurate at 1800 rpm give or take, it is where a 6BT motor makes peak torque and I believe 1700 is where yours peaks.
This is usually the best rpm for pulling power and cruseing economy. I'm not sure where you motor hits the governor, but it has been said that a cummins can run against the governor all day everyday without issues.
So Accuracy at minimum and maximum would be the least important to me.
This is usually the best rpm for pulling power and cruseing economy. I'm not sure where you motor hits the governor, but it has been said that a cummins can run against the governor all day everyday without issues.
So Accuracy at minimum and maximum would be the least important to me.
61 F250 Unibody
5.9 Ford Diesel / Allison auto
& 4WD
5.9 Ford Diesel / Allison auto
& 4WD
- Blackwaterforge
- Posts: 893
- Joined: March 13, 2008, 9:22 am
- Location: Alabama
- Contact:

Re: 1966 F250 Cummins gauges
Thank you
If it cain't be fixed with a sledge hammer it must be an electrical problem!
Re: 1966 F250 Cummins gauges
Well put!FarmMotorSports wrote:Actually I would want it accurate at 1800 rpm give or take, it is where a 6BT motor makes peak torque and I believe 1700 is where yours peaks.
This is usually the best rpm for pulling power and cruseing economy. I'm not sure where you motor hits the governor, but it has been said that a cummins can run against the governor all day everyday without issues.
So Accuracy at minimum and maximum would be the least important to me.
The Ford Orphanage
Life's too short for boring vehicles!
My quest to develop a universal solvent is held up by the lack of a storage container.
Paul
Life's too short for boring vehicles!
My quest to develop a universal solvent is held up by the lack of a storage container.
Paul
