hard spot in the road..

A place for discussion of off topic subjects. Pretty much anything goes - just keep it civil, please!

Moderators: Casey 65, Kid

Post Reply
User avatar
dwbr
Posts: 474
Joined: July 16, 2007, 4:23 pm
Location: Pasadena TX

hard spot in the road..

Post by dwbr »

im at a spot in my engine rebuild, have been working this over in my head till i cant even focus at werk, i started my project small and it quickly spiraled out of control, im at a point where i need to decide to go with a stock 460 crank and rods, pistons bored 40 over or spend another 900 bucks and get the stroker kit with forged rods,pistons, making it a 513. ive allready got all the good bolt on's, edelbrock cam, intake, carb, c9 heads, headers, alum radiator,etc.. the list goes on and on, only thing on the motor that will be original is the block,,one side of me see's the 460 and its power, and what im really going to be doing with it,, but im almost positive at some point im going to be thinking, wonder what that 513 would be like,, whats another 900 bucks more? im almost at the point to just toss a coin...
________
Chevrolet Brookwood specifications
Last edited by dwbr on February 6, 2011, 11:57 pm, edited 1 time in total.
Xcessive
Posts: 136
Joined: October 26, 2007, 7:04 pm
Location: Farmington, Utah
Contact:

Post by Xcessive »

if budget permits I'd go with the stroker man.
shawns fords
Posts: 1111
Joined: March 31, 2007, 11:34 am
Location: Foxfield Colorado
Contact:

Post by shawns fords »

900 bucks is a steal for a stroker kit, I usually see priices for cranks alone for that much. a good set of pistons will run you a good 500 bucks esp forged ones, I havent seen a kit yet for that cheap for either of my engines, I hope the quality of the stroker kit parts is good.
User avatar
Greg D
Posts: 10113
Joined: September 13, 2006, 4:39 pm
Location: Podunk Iowa
United States of America

Post by Greg D »

Only thing that you might want to think about, is the cam, heads and the rest of your parts up to the 514? I'd do it though even if I had to get another cam. Don't know what you were gonna run but you may need a bigger carb too.
1964 F 100 - I am going to do "something" with it.......

viewtopic.php?f=32&t=15942

1987 Mustang LX Convertible, 2.3 Auto - cruiser.
1994 F 150 XLT 2WD


~ Yes - I adopted another cat..............

Cam L Milan,
You'll be missed my friend.
User avatar
dwbr
Posts: 474
Joined: July 16, 2007, 4:23 pm
Location: Pasadena TX

Post by dwbr »

the stroker kit isnt 900, its just 900 more dollars from the cost of the new 460 hardware, .. budget,, its close, i still want to buy rims and tires before i put it back on the road, top end hardware is solid, c9 heads with 3 angle valve job, stainless valves, bowl blended etc, crane stailess roller rockers, hardede pushrods with guides,edelbrock rpm cam, eldelbrock rpm intake, edelbrock performer 800 cfm carb,k&n extreme air filter.. i think the thing that is starting to bother me is i have spent as much money on the engine as i have on the whole truck,, know what i mean ?
________
First-generation Taurus
Last edited by dwbr on February 6, 2011, 11:57 pm, edited 1 time in total.
Phil
Posts: 2125
Joined: June 1, 2007, 9:37 pm
Location: toledo

Post by Phil »

Is that the Ohio crankshaft setup? $1300

Man I spent more on my Fairlane engine than the car, the interior and paint combined cause I broke it 3 times in a year.

I'd be afraid to spend on a big one and build it myself.
I know I'd mess up on something stupid and have to redo it.
Someday I'll get another slick :(
Image
shawns fords
Posts: 1111
Joined: March 31, 2007, 11:34 am
Location: Foxfield Colorado
Contact:

Post by shawns fords »

OK I see, you have spent a fortune already. might as well spend another 900 for them extra 40 cubes. but then again. do you really need them? is it a full out drag truck? so many people buy a stroker kit just to say they have one yet they dont even need the fuckin thing. I plan on building a stroker engine myself but its for a Drag car. I will be going from 429 cubes to 514 or more. if I already had a 460 crank. I would just run that instead. As long as its a good piece of metal still
User avatar
dwbr
Posts: 474
Joined: July 16, 2007, 4:23 pm
Location: Pasadena TX

Post by dwbr »

shawns fords wrote:OK I see, you have spent a fortune already. might as well spend another 900 for them extra 40 cubes. but then again. do you really need them? is it a full out drag truck?
you see thats just it, no its not going to be a full drag truck, i plan on taking it to the track, on street night with the guys, they have mustangs, and vettes,..but i also plan on driving thru the sonic on sat nights,..and mine started out as the 429, then i decided to go 460, and then i started looking at the strokers,,my little mind goes berzerk, if i get the stroker i can never say, man i wish i hadda, but then if i get the stroker will i say, i didnt need all that,, hmmm.. i think im just going to go with the stroker
________
MT-100
Last edited by dwbr on February 6, 2011, 11:57 pm, edited 1 time in total.
jeepbut
Posts: 652
Joined: April 15, 2006, 8:15 pm
Location: Corpus Christi, Texas
United States of America

Post by jeepbut »

The hell with new wheels------STROKE IT !!!!!!! Thanks, Lyman.
User avatar
Jarrod
Posts: 361
Joined: July 17, 2006, 3:11 pm
Location: California

Post by Jarrod »

If 900 won't kill your budget then stoke the thing. But often times adding more cubic inches can lead to other problems. You have good heads for the 460, but will those heads support the 514? Same thing with the cam. The additional cubic inches will change the dynamic of the cam and how it acts during the RPM range? Will your carb and intake run out of steam at the upper end of the power band with the 514? the list goes on. Will the additional power destroy the rest of the drive train when you get on it? A stroker is cool and I want to put a stroker 428 in mine. These are all questions that I need to figure out.
Cheers,
Jarrod
User avatar
Uncle Skip
Posts: 4695
Joined: July 15, 2006, 8:30 pm
Location: Pearland, Texas
United States of America

Post by Uncle Skip »

Doug.
Give me a call. I need to introduce you to Dale here in Houston. He's doing the same thing and he has extra parts for sale..... aluminum heads..... and who knows what else.
You need to meet him.
And, get in touch with FordboyPete. He's the resident expert on the 460 conversion.
Skip
I'm not arguing with you. I'm just explaining why I'm right.
Pardon me. Does your deaug bite?
User avatar
FORDMANLCRACKEL
Posts: 1237
Joined: July 11, 2006, 9:48 pm
Location: williamston, n.c.
Contact:
United States of America

Post by FORDMANLCRACKEL »

Here's some interesting reading, it might help http://www.highflowdynamics.com/ and www.460ford.com
but to answer your question, just skip 514 and go for 545 stroker.

Lonnie
The most rewarding job i ever had was being a dad.
1988 Ranger Build http://s275.photobucket.com/albums/jj31 ... %20RANGER/
blackagatha
Posts: 2582
Joined: March 10, 2007, 12:49 am
Location: Arizona

Post by blackagatha »

get as much out of it as you can!

I put over $3000 into my 390. It's maybe a bit warmer than stock... it makes me sad that I didn't go all the way. SOMEDAY I will have to yank it out again and "upgrade" it. For the time being though, it's a good thing that it's mild, if nothing else, it isn't chugging the gas, it is just drinkin real fast!
'63 with 390 & lots of juice. But never enough. Always want more.
ImageImageImage
Post Reply