Been gone a little while. What I've been up to.

A place for discussion of off topic subjects. Pretty much anything goes - just keep it civil, please!

Moderators: Casey 65, Kid

User avatar
ripsnorter
Posts: 607
Joined: November 12, 2006, 5:23 am
Location: Washington State

Been gone a little while. What I've been up to.

Post by ripsnorter »

Been gone a little while, so I thought I'd pop back in and see what ya'll had been up to. I just finished reading about 6 pages of posts 8)

Me:

I spent probably 3-4 days rewiring my new '77 4x4 I just bought. Among the lovely ideas the previous owner had were:

"dont know why the tach doesnt work, we think its a bare wire rubbing against the dash cus when you hit the brakes it rubs just right and sometimes works"

Actually what had happened was they had wired the hot wire for the tach into the brake lights. :roll: Apparently they had their foot on the brake when they were wiring it and just grabbed the first hot wire they found.

4 seperate hot wires running straight from the battery through fused links all the way to the back of the truck. 1 of which was wired straight into the left tail light. I guess they REALLY wanted that taillight on. Fortunately all of the 4 were ripped apart, cut, or similiary screwed up and nothing worked.

Melted wires and shorts galore in the fuse block.

like BlackAgatha, I think I pulled at least 20' of excess wire out of the truck. Scratch that, more like 80+ because of the FOUR freakin hot wires running to the rear which served no purpose.

They liked to wire things up with speaker wire. yay.

The list goes on. One of my favorites though was their splicing jobs... they literally had over 8 splices in one 6 inch length of harness. however none of them actually went anywhere. Their thoughts seemed to run along the lines of "I think I'll splice into this. No wait I'll splice into my splice. No wait I wont use any of that. No wait I'll splice into that again..."

I believe I've finally tracked down and fixed 95% of the problems in the truck though. With the exception of the backup light switch not working and a few wires running down to the transmission that I didn't feel like taking the transmission hump out to fix. I now at least have all working gauges, (save the ammeter that I didnt care to screw with) a conversion to the newer ford Mini-Starter, working gas gauges and fuel pump all wired into 1 single switch. I just found that I have a battery drain though, so I've got a little work ahead of me still.

On a high note though... I'm finally getting started on building my shop :D

Words can't describe how excited and relieved I am about this. I've been waiting over a year, (actually more like 10 years if you want to be specific) to get started on this, and its a big "yeehawww" to finally be getting going. I have 2 poles in the ground at the moment, and a pile of 160 2x6s sitting waiting for framing. Trusses are coming in roughly 2 weeks, and I'm hoping to have all the framing done by then and ready for them to set them in place when the trusses get here. I know it shouldnt normally take that long but I'm doing almost all the work by myself and things take about 5 times as long without an extra set of hands. I'm running into one of those rare times in my life when I'm really wishing there were more work hours in a day so I could work longer I'm having so much fun. Darkness coming on is a sad time :lol:

Anyway, I'm still alive and kicking, but busy and having fun at the same time. 8)
User avatar
ripsnorter
Posts: 607
Joined: November 12, 2006, 5:23 am
Location: Washington State

Post by ripsnorter »

I've got a few pictures of my shop site and a few of the wiring mess I had to fix. When I get my camera back I'll post 'em up if anyone cares to see them.
User avatar
ripsnorter
Posts: 607
Joined: November 12, 2006, 5:23 am
Location: Washington State

Post by ripsnorter »

Pics as promised.

Partial pics of some of the wiring mess on the '77.

Image

Image

The as yet non-glorious site of my shop.

Image

Image

Image

Image
ICEMAN6166
Posts: 11470
Joined: July 11, 2006, 11:28 am
Location: Dove Creek, Co. elevation 6842
Poland

Post by ICEMAN6166 »

Rip nice to see you back.
you should have come up here with your backhoe and helped me with my shop before the ground froze. :lol:
1966 F250 4x4
1964 Rambler Ambassador 990
Rest in peace departed Slick family members
Cam Milam
Lesley Ferguson
Steve Lopes
John Sutton
User avatar
Slick Fan
Posts: 4085
Joined: November 4, 2006, 5:09 pm
Location: UTAH...snow blows!

Post by Slick Fan »

That wiring mess is quite the spaghetti mess! :shock: Glad you got 'er figured out. I had a bunch of extra wires from stereo's & CB's in the past to remove from my brown Highboy...most of which was stuffed under the carpet to hide. I'm glad it wasn't as bad as yours. :)

Looks like you're building a pole barn type shop? How big? That's definitely the way I'm going, when I build one for me. :thumright:
Looking forward to progress pics! :D
My "Slickitis" affliction began here...
Image


66 F100 CC/65 F100 CC/66 F250 CC
If it starts to rain, they'll tax the splash.
If you want to fish, they'll tax the bass.
If you plant a yard, they'll tax the grass.
If you don't play nice, they'll fine your *$#!
GLindley
Posts: 562
Joined: July 11, 2006, 9:47 pm
Location: Springfield, MO

Post by GLindley »

Rip, ya gonna pour a concrete floor?
Gene
1961 Intregal cab SWB 223 (getting 302 & TIB)
1969 LWB 302 automatic (Donor for the '61)
2000 F150 XLT SWB (Daily Driver)
User avatar
ripsnorter
Posts: 607
Joined: November 12, 2006, 5:23 am
Location: Washington State

Post by ripsnorter »

Ice: Thats actually my dad's backhoe. Its an old late 60s/early 70s warhorse, very worn out, but it gets the job done :) I spent about 2 weeks (most of it waiting on parts) a few months ago redoing all the power steering etc, so it finally has working power steering. I've been thinking about buying a 'hoe of my own, but I'd probably get a CASE 580C instead since thats what I learned on. Or a CAT.

Slick and Gene: Going to be 20x40 with plans of adding on a 20x25 lean to almost immediately, and hopefully in the next few years extending the main building to 40x100 or even 40x140 if my business does well. And yep, pouring a floor in it. 4" pad with 6" and a hoist in mind in some of the later bays.
User avatar
Jarrod
Posts: 361
Joined: July 17, 2006, 3:11 pm
Location: California

Post by Jarrod »

You said hoe :lol: :lol: :lol: :lol:

Just kidding. I am jealous. I want a shop. My little 50x120 lot won't cut it
Cheers,
Jarrod
User avatar
Slick Fan
Posts: 4085
Joined: November 4, 2006, 5:09 pm
Location: UTAH...snow blows!

Post by Slick Fan »

Jarrod wrote:
Just kidding. I am jealous. I want a shop. My little 50x120 lot won't cut it
You & me both, brotha. :wink:
The wife & I are gonna slap our house on the market next spring & go find something that has more elbow room for a nice big shop. 8) It wouldn't hurt my feelings if the shop was already built, either. :lol:
My "Slickitis" affliction began here...
Image


66 F100 CC/65 F100 CC/66 F250 CC
If it starts to rain, they'll tax the splash.
If you want to fish, they'll tax the bass.
If you plant a yard, they'll tax the grass.
If you don't play nice, they'll fine your *$#!
User avatar
Ford4jack
Posts: 707
Joined: July 22, 2006, 7:56 am
Location: Tennessee

Post by Ford4jack »

Good luck with your shop ripsnorter sounds like it will be nice.

If you get a hoe a C or D series Case is a good choice.
Very simple machines and there low cost to maintain & rebuild as far as backhoes go.
Brakes seem to be a weak point on them but as they say that's what the front bucket is for :lol:

Remember the good thing about extra wiring is copper scrap prices are up.
User avatar
Comet
Posts: 775
Joined: July 5, 2006, 10:03 pm
Location: Charleston, SC

Post by Comet »

Wow, what a wiring mess! Good work in getting that cleared up.
Cool about the shop! I'm buying a new house as soon as mine sells and building a shop myself. Rip, where abouts do you live?
My Slick is rustier than your Slick! :D
User avatar
ripsnorter
Posts: 607
Joined: November 12, 2006, 5:23 am
Location: Washington State

Post by ripsnorter »

Comet, I'm down in lewis county, about 20 minutes south of Chehalis/Centralia area. Theres actually quite a few 5 acre lots around me for sale. We're down on the Cowlitz river. I'm even halfway considering selling my place (10 acres) and moving a little further out. I'm thinking about moving to eastern Lewis County, I figure I can tolerate a 30 minute drive to the freeway if I can find 40-100 acres. (I'm a bit of a hermit heh.)

I'll take some more pics tomorrow and put them up. I couldnt do much yesterday with the windstorm, I did do some though. Today wasnt too productive either, things keep coming up that I need to take care of elsewhere, but I did get all 4 corner posts squared, leveled, set and rocked in. Got all of my other posts in their holes but not set yet. It should go a lot quicker now that I have my corners set.
BigTim
Posts: 890
Joined: August 6, 2006, 4:26 pm
Location: Slickless

Post by BigTim »

ford4jack wrote: Brakes seem to be a weak point on them but as they say that's what the front bucket is for :lol:
Ya think :shock:
Image
BigTim
Posts: 890
Joined: August 6, 2006, 4:26 pm
Location: Slickless

Post by BigTim »

Oh yeah congrats on the barn start Rip, you will really enjoy it.
User avatar
Slick Fan
Posts: 4085
Joined: November 4, 2006, 5:09 pm
Location: UTAH...snow blows!

Post by Slick Fan »

Holy crap! :laughing:
My "Slickitis" affliction began here...
Image


66 F100 CC/65 F100 CC/66 F250 CC
If it starts to rain, they'll tax the splash.
If you want to fish, they'll tax the bass.
If you plant a yard, they'll tax the grass.
If you don't play nice, they'll fine your *$#!
User avatar
Ford4jack
Posts: 707
Joined: July 22, 2006, 7:56 am
Location: Tennessee

Post by Ford4jack »

YEOW :shock:

What happened there someone forget to boom it down?
blackagatha
Posts: 2582
Joined: March 10, 2007, 12:49 am
Location: Arizona

Post by blackagatha »

hahaha that tractor is incredible.


Rip, I would build it 40 ft deep in the first place if the plan is to expand it...

haha my wiring was pretty bad, but NOT Like THAT... Most of what I just re-wired was my own work... It made perfect sense when I was 14... At least it was safe... I was still willing to vouch for that, even as I was ripping it out.

NOW, some of the stuff going on when I bought ol Aggie was kinda loopy... The biggest electrical "bad idea" was the rolled up chunk of a Pepsi can in the fuse slot for the brakelights... They apparently had it keep blowing the fuse, and never checked to see why. The ENTIRE LENGTH of the wire was charred and blistered. Not one inch of wire was not burnt.

That tach wired into the brakelight wire is pretty comical...
'63 with 390 & lots of juice. But never enough. Always want more.
ImageImageImage
User avatar
ripsnorter
Posts: 607
Joined: November 12, 2006, 5:23 am
Location: Washington State

Post by ripsnorter »

blackie:

Its actually 40 feet WIDE and 20 feet Long, not 20 wide and 40 long. Meaning that the trusses are running 40 feet wide and I'm basically building a 20 foot section of a 40x100 shop. I would have loved to have built a 40x40, but can't afford it at the moment. This way however I wont have two different rooflines if I add on. It'll look really silly if I don't add on to it though heh. And once again I've forgotten my camera out in my truck, so I guess I'm updating pictures tomorrow rather than tonight.

And the rolled up pepsi can reminds me of a friend of ours that went to fix a big expensive mill. they kept blowing those big 1" fuses, so they just cut off a chunk of 1" round stock aluminum and used that to replace the fuse. Our friend went out and I believe they ended up with a $20,000 bill to fix all the stuff they had fried by the time they were done. Another neighbor of ours got tired of blowing sheer pins on his tractor's PTO driveshaft, so he welded it solid. Couldnt understand why his gears got chewed to bits after that either :lol:
blackagatha
Posts: 2582
Joined: March 10, 2007, 12:49 am
Location: Arizona

Post by blackagatha »

ripsnorter wrote:blackie:

Its actually 40 feet WIDE and 20 feet Long, not 20 wide and 40 long. Meaning that the trusses are running 40 feet wide and I'm basically building a 20 foot section of a 40x100 shop. I would have loved to have built a 40x40, but can't afford it at the moment. This way however I wont have two different rooflines if I add on. It'll look really silly if I don't add on to it though heh. And once again I've forgotten my camera out in my truck, so I guess I'm updating pictures tomorrow rather than tonight.

And the rolled up pepsi can reminds me of a friend of ours that went to fix a big expensive mill. they kept blowing those big 1" fuses, so they just cut off a chunk of 1" round stock aluminum and used that to replace the fuse. Our friend went out and I believe they ended up with a $20,000 bill to fix all the stuff they had fried by the time they were done. Another neighbor of ours got tired of blowing sheer pins on his tractor's PTO driveshaft, so he welded it solid. Couldnt understand why his gears got chewed to bits after that either :lol:
haha that is sort of a funny roofline, but whatever... it works. Good thinkin about add ons...
Just make the doors tall enough to get big things in... my dad's 89 F350 BARELY fits thru the door, and doesn't fit in the garage, as the bays are too shallow. not good for big repairs...

HAHA safety devices are installed for a good reason.... If they blow, IT MEANS THERE IS A PROBLEM!!!! HAHAHA but people get stupid....
'63 with 390 & lots of juice. But never enough. Always want more.
ImageImageImage
User avatar
ripsnorter
Posts: 607
Joined: November 12, 2006, 5:23 am
Location: Washington State

Post by ripsnorter »

Got some more updated pics.

Sadly I didnt get a whole lot accomplished this week, (getting sidetracked sucks) but at least its coming along.

My four corner poles in.

Image

All the poles in the ground, waiting to be set in rock. Looks like a teepee/A-frame. Maybe I should consider a design change :D

Image

One side planted. This took forever as the holes are 18" in diameter and I have to tamp the rock in with a steel rod every 8 inches or so.

Image

Heres todays shot. All my poles are set and I have a little shelter for my saw and compressor out of the weather. I got my first framing boards nailed in :D You can also see my '63 and part of my '69 4x4 in the foreground.

Image

A closer shot of the start of my framing. Pretty excited about this.

Image

So there you have it. Stay tuned next week and we'll see if I get anymore done :)
Post Reply