Removing Glue from Hardwood floors
Removing Glue from Hardwood floors
Anyone have any experience doing this?
My wife has been nagging me for what seems like a life time to take up our carpet and have hard wood floors. I told her the carpet was glued down by the PO and I really didn't want to mess with it.
Well she decided to do it herself anyway so now my wieght room has no carpet and ugly ass glue streaked hardwood floors.
She's been scraping the glue off by hand since she don't work and has all this spare time but I'm tired of looking at it plus she wants the whole house done.
She tried boiling hot water and said that didn't work and we can't use any harse chemicals because we have indoor pets.
Any ideas?
Signed stuck between my wife and a hard wood floor.
My wife has been nagging me for what seems like a life time to take up our carpet and have hard wood floors. I told her the carpet was glued down by the PO and I really didn't want to mess with it.
Well she decided to do it herself anyway so now my wieght room has no carpet and ugly ass glue streaked hardwood floors.
She's been scraping the glue off by hand since she don't work and has all this spare time but I'm tired of looking at it plus she wants the whole house done.
She tried boiling hot water and said that didn't work and we can't use any harse chemicals because we have indoor pets.
Any ideas?
Signed stuck between my wife and a hard wood floor.
'01 F150 Lightning
490RWHP
Gas Mileage? What's that?
Jerry
490RWHP
Gas Mileage? What's that?
Jerry
-
ICEMAN6166
- Posts: 11470
- Joined: July 11, 2006, 11:28 am
- Location: Dove Creek, Co. elevation 6842

i used to install floor coverings.
new glue is easily removed with goo gone or WD40
other than sanding your wood floor or using a chemical there is no good way to remove old dry glue from hardwood floors.
new glue is easily removed with goo gone or WD40
other than sanding your wood floor or using a chemical there is no good way to remove old dry glue from hardwood floors.
1966 F250 4x4
1964 Rambler Ambassador 990
Rest in peace departed Slick family members
Cam Milam
Lesley Ferguson
Steve Lopes
John Sutton
1964 Rambler Ambassador 990
Rest in peace departed Slick family members
Cam Milam
Lesley Ferguson
Steve Lopes
John Sutton
- Johnny Canuck
- Posts: 8291
- Joined: April 9, 2006, 11:14 pm
- Location: Edmonton, Alberta.

Aba. Ever time I see your name I hear the little voice in my brain sing....
Mamma mia, here I go again
My my, how can I resist you?
Mamma mia, does it show again?
My my, just how much Ive missed you
LOL
No I am NOT gay
Mamma mia, here I go again
My my, how can I resist you?
Mamma mia, does it show again?
My my, just how much Ive missed you
LOL
No I am NOT gay
It's a race.. Will hell freeze over or will JC finish his truck first. Stay tuned..
-
ICEMAN6166
- Posts: 11470
- Joined: July 11, 2006, 11:28 am
- Location: Dove Creek, Co. elevation 6842

was doing a job one time, while we were at lunch the lady of the house spilled a can of oil paint all over the freshly installed linoleum in her kitchen, when we got back, she was in tears. we sent her to buy the gallon can of wd40, and by the time we got done with the rest of the job, the paint was gone, floor good as new but slippery as an eel. got a nice grant
from that lady.
1966 F250 4x4
1964 Rambler Ambassador 990
Rest in peace departed Slick family members
Cam Milam
Lesley Ferguson
Steve Lopes
John Sutton
1964 Rambler Ambassador 990
Rest in peace departed Slick family members
Cam Milam
Lesley Ferguson
Steve Lopes
John Sutton
What, you mean you're not the Dancing Queen?Johnny Canuck wrote:Aba. Ever time I see your name I hear the little voice in my brain sing....
Mamma mia, here I go again
My my, how can I resist you?
Mamma mia, does it show again?
My my, just how much Ive missed you
LOL
No I am NOT gay
I been getting that a lot lately. Seems to be a bunch of ABBA fans coming out of the closet as of late.
I'm thinking we may end up just installing hardwood laminent over the original floor. I'm just waiting for the wife to get tired of scraping so I can tell her I told ya so.
'01 F150 Lightning
490RWHP
Gas Mileage? What's that?
Jerry
490RWHP
Gas Mileage? What's that?
Jerry
- Uncle Skip
- Posts: 4695
- Joined: July 15, 2006, 8:30 pm
- Location: Pearland, Texas

I wouldn't use WD40 for this job because it might get in the wood and keep your new finish from staying on.
Get some of that (aircraft) paint stripper in a can, not the aerosol spray. Brush small patches, say 5'x5', let it sit for about 5 minutes and then use one of those sharp dry wall mud knives to scrape up the glue.
Comes up really nice.
Use a rag and water to wipe the excess up and try not to get it on your hands.
Its a caustic and will burn your skin.
Get some of that (aircraft) paint stripper in a can, not the aerosol spray. Brush small patches, say 5'x5', let it sit for about 5 minutes and then use one of those sharp dry wall mud knives to scrape up the glue.
Comes up really nice.
Use a rag and water to wipe the excess up and try not to get it on your hands.
Its a caustic and will burn your skin.
I'm not arguing with you. I'm just explaining why I'm right.
Pardon me. Does your deaug bite?
Pardon me. Does your deaug bite?
Yeah I figured as much with the WD 40.Uncle Skip wrote:I wouldn't use WD40 for this job because it might get in the wood and keep your new finish from staying on.
Get some of that (aircraft) paint stripper in a can, not the aerosol spray. Brush small patches, say 5'x5', let it sit for about 5 minutes and then use one of those sharp dry wall mud knives to scrape up the glue.
Comes up really nice.
Use a rag and water to wipe the excess up and try not to get it on your hands.
Its a caustic and will burn your skin.
What about fumes with the aircraft paint stripper, like I stated above we have indoor pets.
Too cold to put the birds out.
Oh about sanding Jarod, the glue will clog up the sandpaper.
I was thinking maybe something like a rust remover, can't think of what it's called, goes on a drill, has a 1/2 inch think disk type wheel on it but it's very porous.
Ahh, I found it. HeHe, it would be on a VW restro site.
http://www.vwtrendsweb.com/tech/0401vwt ... to_02.html
'01 F150 Lightning
490RWHP
Gas Mileage? What's that?
Jerry
490RWHP
Gas Mileage? What's that?
Jerry
Those actually work real good (I have a similar set up for my 4" angle grinder) just be careful you don't cut into the wood with them.
1964 F 100 - I am going to do "something" with it.......
viewtopic.php?f=32&t=15942
1987 Mustang LX Convertible, 2.3 Auto - cruiser.
1994 F 150 XLT 2WD
~ Yes - I adopted another cat..............
Cam L Milan,
You'll be missed my friend.
viewtopic.php?f=32&t=15942
1987 Mustang LX Convertible, 2.3 Auto - cruiser.
1994 F 150 XLT 2WD
~ Yes - I adopted another cat..............
Cam L Milan,
You'll be missed my friend.
-
blackagatha
- Posts: 2582
- Joined: March 10, 2007, 12:49 am
- Location: Arizona
-
shawns fords
- Posts: 1111
- Joined: March 31, 2007, 11:34 am
- Location: Foxfield Colorado
- Contact:
ok I tried to reply three times, and had problems with the link to NWFA so ill shorten it up, I do wood floord, 7 years, dust contained, and guaranteed, find someone like us and uses water based finishes, you wont regret it, lol got questions, let me knowABA wrote:Yeah I figured as much with the WD 40.Uncle Skip wrote:I wouldn't use WD40 for this job because it might get in the wood and keep your new finish from staying on.
Get some of that (aircraft) paint stripper in a can, not the aerosol spray. Brush small patches, say 5'x5', let it sit for about 5 minutes and then use one of those sharp dry wall mud knives to scrape up the glue.
Comes up really nice.
Use a rag and water to wipe the excess up and try not to get it on your hands.
Its a caustic and will burn your skin.
What about fumes with the aircraft paint stripper, like I stated above we have indoor pets.
Too cold to put the birds out.
Oh about sanding Jarod, the glue will clog up the sandpaper.
I was thinking maybe something like a rust remover, can't think of what it's called, goes on a drill, has a 1/2 inch think disk type wheel on it but it's very porous.
Ahh, I found it. HeHe, it would be on a VW restro site.![]()
http://www.vwtrendsweb.com/tech/0401vwt ... to_02.html
We use open coat paper to get the glue and whatever else off, dust contained down to less than 1 micron through our HEPA filters

this is the good side
-
shawns fords
- Posts: 1111
- Joined: March 31, 2007, 11:34 am
- Location: Foxfield Colorado
- Contact:
there is alot more to it than just sanding it down, getting it done right, using the vproper filler to fill in the soft grain of the wood to help the durability. getting all of your sanding marks out, so its nice and flat, etc etc we usualyl get most jobs done in two days because we use water based, but I noticed also you live in NC so you might need moisture cured for the more humid climates. I dont know much about them, but can find more out of you need

this is the good side
pour some gasoline, lighter fluid, kerosene,, etc,, whatever ....all over the floor, set it on fire, the glue and the nasty wood floors will burn away,, no more worries 
________
The cigar boss
________
The cigar boss
Last edited by dwbr on March 26, 2011, 12:58 pm, edited 1 time in total.
- Alan Mclennan
- Posts: 9324
- Joined: October 14, 2006, 6:16 pm
- Location: In the shed... Cranebrook NSW




