68 Fairlane cowl repair. Pix!

A place for discussion of off topic subjects. Pretty much anything goes - just keep it civil, please!

Moderators: Casey 65, Kid

Post Reply
Phil
Posts: 2125
Joined: June 1, 2007, 9:37 pm
Location: toledo

68 Fairlane cowl repair. Pix!

Post by Phil »

Johnny banged this out today with my POS $50 Sears welder:
I was pretty much a tool caddy. Did a little welding and prepped parts as he stuck em on.

Image

Image

Image

Image

Image

Kid drilled holes in stuff

Image

Image
Someday I'll get another slick :(
Image
36truck
Posts: 3152
Joined: October 20, 2007, 8:32 pm
Location: Land of Sunshine AZ
United States of America

Post by 36truck »

Looks much better now Phil.
Tom Williams
User avatar
Greg D
Posts: 10113
Joined: September 13, 2006, 4:39 pm
Location: Podunk Iowa
United States of America

Post by Greg D »

That looks good!
1964 F 100 - I am going to do "something" with it.......

viewtopic.php?f=32&t=15942

1987 Mustang LX Convertible, 2.3 Auto - cruiser.
1994 F 150 XLT 2WD


~ Yes - I adopted another cat..............

Cam L Milan,
You'll be missed my friend.
blackagatha
Posts: 2582
Joined: March 10, 2007, 12:49 am
Location: Arizona

Post by blackagatha »

I just remembered a question i had, how did you remove the slat panel, cut it or unscrew or what?
'63 with 390 & lots of juice. But never enough. Always want more.
ImageImageImage
Phil
Posts: 2125
Joined: June 1, 2007, 9:37 pm
Location: toledo

Post by Phil »

blackagatha wrote:I just remembered a question i had, how did you remove the slat panel, cut it or unscrew or what?
Not sure what you mean by "slat panel"

If you mean the whole assembly we cut out the OEM with a cutoff wheeel then ground all the spotwelds of the remaining pieces


Did the same with the donor part.

We then drilled holesin the donor part where the spotwelds were
and tacked it all together. Alon the front we were going to but weld the firewall to the nub I left but we ended up lapping it to hide some voids. Seam sealer will cover anything you see and keeep the H2o out but to be honest, you can't see anything at all. John was dissapointed with the welds and the look but I couldn't be happier. Its as good as factory all over.
I have another post showing removal in this section someplace
Someday I'll get another slick :(
Image
User avatar
Johnny Canuck
Posts: 8291
Joined: April 9, 2006, 11:14 pm
Location: Edmonton, Alberta.
Canada

Post by Johnny Canuck »

I am in awe.

This is so far away from any skills that I have, it might as well be on mars

One question Phil, why didn't you soak down the rusty kick panels etc with Ospho while you had it apart?
It's a race.. Will hell freeze over or will JC finish his truck first. Stay tuned..
Phil
Posts: 2125
Joined: June 1, 2007, 9:37 pm
Location: toledo

Post by Phil »

Johnny Canuck wrote:I am in awe.

This is so far away from any skills that I have, it might as well be on mars

One question Phil, why didn't you soak down the rusty kick panels etc with Ospho while you had it apart?
I know I know, I should have but I have been on a scheule and John is only available on Sundays. He missed last week cause I didn't get the cowl stripped and he was sick. Had I missed this Sunday it would have just gotten worse timewise. I need to roll the car around the garage and I wasn't about to move it all hacked up.

On top of time constraints I plan on POR 15ing stuff and that crap doesn't ever stick to clean metal for me, all that rusty stuff is surface.
I am on the fence though about POR, I may Blu lighning it all clean and use my siphon fed POS gun and etch or epoxy prime everything. John said I should have dipped and E-coated it.

I am making this up as I go along and probably skipping important steps but in the end I am building a driver. I'll never do another resto. The cars are just too scary to use. When they are that nice they keep me awake at night.

Also this car, while I like it, its just an impediment to getting to my Unibody :twisted:
Someday I'll get another slick :(
Image
User avatar
Slick Fan
Posts: 4085
Joined: November 4, 2006, 5:09 pm
Location: UTAH...snow blows!

Post by Slick Fan »

Looks pretty darn good, your friend sure makes it look simple. :thumright:
My "Slickitis" affliction began here...
Image


66 F100 CC/65 F100 CC/66 F250 CC
If it starts to rain, they'll tax the splash.
If you want to fish, they'll tax the bass.
If you plant a yard, they'll tax the grass.
If you don't play nice, they'll fine your *$#!
GLindley
Posts: 562
Joined: July 11, 2006, 9:47 pm
Location: Springfield, MO

Re: 68 Fairlane cowl repair. Pix!

Post by GLindley »

Heavyhauler wrote:
Kid drilled holes in stuff

Image
Hey Phil, how quickly did he learn to be careful when the bit is breaking through that it "catches" and breaks your wrist?!?
Gene
1961 Intregal cab SWB 223 (getting 302 & TIB)
1969 LWB 302 automatic (Donor for the '61)
2000 F150 XLT SWB (Daily Driver)
Phil
Posts: 2125
Joined: June 1, 2007, 9:37 pm
Location: toledo

Post by Phil »

Brand new sharp bits + redwood. Even a 6yr old can do it
Someday I'll get another slick :(
Image
GLindley
Posts: 562
Joined: July 11, 2006, 9:47 pm
Location: Springfield, MO

Post by GLindley »

I guess if I was more observant, I'd a noticed the Sawdust and not metal chips!
Being more observant, it's a character flaw of mine, just ask the wife!
Gene
1961 Intregal cab SWB 223 (getting 302 & TIB)
1969 LWB 302 automatic (Donor for the '61)
2000 F150 XLT SWB (Daily Driver)
ICEMAN6166
Posts: 11470
Joined: July 11, 2006, 11:28 am
Location: Dove Creek, Co. elevation 6842
Poland

Post by ICEMAN6166 »

Bodywork is not my strong suit either. glad most of my patches are covered by the floor mats. will never have a show car or truck that i did the bodywork on but i am more interested in driving them than worrying about scratches.
looks real good Phil.
1966 F250 4x4
1964 Rambler Ambassador 990
Rest in peace departed Slick family members
Cam Milam
Lesley Ferguson
Steve Lopes
John Sutton
Post Reply