If you understand what you’re doing, you’re not learning anything.
LITTLE RED: 64 F100 Short Style
BIG RED: 62 F100 Long Uni
BIG “UN": 63 F250 Long Flare
BBW RED: 61 F100 CC BBW Long Uni
CRIMSON CREW: 63 F100 "Stageway" Long Flare Crew Cab
"RANGER": 66 F100 CC Long Flatbed
"AVA" 1963 Avion T-20 Travel Trailer
“Lucille” 1955 New Moon 44’ Travel Trailer
OMG, that is almost as pretty as my son right after he was born. Well maybe not right after. GREAT job. Were those parts cleaned up or are they new? I will save the pics to use when I get confused when I do my conversion. Again great job and thanks for the pictures.
Richard , nice work mate! brings back memories but with out grease dirt and tools everywhere . I noticed your radius arms are made of pressed steel where as mine are cast iron are they after market or original nice pic`s too!
Alan,
Honey, If I say I`ll fix something I will, there`s no need to remind me every 6 months!!
66 f100 tabletop swb 351 Clevo C6 "Beryl"
Hey,
Just a replay to Ras4432 & Alan.
The parts are from a 77 f150 I took every thing for the front end and pressured washed the axle, radius arms & spindles and then I wired brushed everything to get the rust and dirt off that didn't come off with the pressure washer. Then before the install I painted every thing with Hammer paint from Home depot. I used the springs from my 66 and then replaced the rotors, calipers, bearings, seals, pads drag link, tie rod ends and bushings that I brought from NAPA. Just follow the Technical form for the Disc Brake swap and every thing works great. I had now problems. The 66 had kingpin problems and the 77 had been replace only a few years back. I will keep the old 66 front end in case someone needs parts.
Richard
I wish my front end looked that nice! but alas, when I installed my front disks on the straight axle, I was in a pinch for time and didnt even rightfully clean the axle! I just scraped the crap back from the spindle for the install...
SOME DAY it will be all shiny and Ford Red... Some Day....
and I wish my brakes didnt use those stupid C#@^Y calipers!!! I like your ford ones much better... and they actually have backing plates!
'63 with 390 & lots of juice. But never enough. Always want more.
That's about how the front end on my '66 looked...a looong time ago.
I like the paint color on yours, looks great!
My "Slickitis" affliction began here...
66 F100 CC/65 F100 CC/66 F250 CC
If it starts to rain, they'll tax the splash.
If you want to fish, they'll tax the bass.
If you plant a yard, they'll tax the grass.
If you don't play nice, they'll fine your *$#!
Alan Mclennan wrote:Richard , nice work mate! brings back memories but with out grease dirt and tools everywhere . I noticed your radius arms are made of pressed steel where as mine are cast iron are they after market or original nice pic`s too!
Alan,
They switched to stamped some time in the late 70's Might be 76, but not sure.
Alan Mclennan wrote:Richard , nice work mate! brings back memories but with out grease dirt and tools everywhere . I noticed your radius arms are made of pressed steel where as mine are cast iron are they after market or original nice pic`s too!
Alan,
They switched to stamped some time in the late 70's Might be 76, but not sure.
Good looking job so far!
Thanks for the info Dan,
Alan,
Honey, If I say I`ll fix something I will, there`s no need to remind me every 6 months!!
66 f100 tabletop swb 351 Clevo C6 "Beryl"
Ok,
Here it is.
Completed the front end install Shocks, Steering box, Adj. Front end and Painted the Cab bottom, Installed new Cab Rubbers. Painted front of Cab.
A lot of work and it was Hot.('')
See you next week end.
Richard