need some guru advice

The place to talk Slicks. All we ask is that discussion has something to do with slicks...

Moderators: Casey 65, Kid

Post Reply
User avatar
lane
Posts: 19
Joined: November 22, 2009, 9:59 pm
Location: Pasadena, CA
Contact:
United States of America

need some guru advice

Post by lane »

I just bought another 66. It's got a 390, 4-speed manual, 9" rear end and has air conditioning in it. It looks like all this stuff came standard, but I haven't seen anything that says 390 came in these. I do know that 352's were stock. Can anybody tell me what motors came in these or guide me to a place that will tell me more about this particular truck.

Lane
A happy life is a simple life.
User avatar
66ford
Posts: 427
Joined: January 18, 2010, 2:03 pm
Location: Upstate New York

Post by 66ford »

From what i have read(Yhough i may be wrong) Is that the 352 was the largest for a slick?
Image
1966 LWB 352
1969 Fairlane Conv't, 302.
16 and loving life.
R.I.P Cam
User avatar
ezernut9mm
Posts: 9141
Joined: July 21, 2006, 9:37 pm
Location: KCMO
Sweden

Post by ezernut9mm »

yep, 352 through 67, then the 360 in 68.
always
"i believe i've achieved satisfaction".-bubbles
"should i be gettin" baked for this boys?"-bubbles


i could no longer keep "r.i.p.ing" all of our fallen brothers and sisters, so i say here, slick loads of love and much respect to all you beautiful people.
User avatar
Greg D
Posts: 10113
Joined: September 13, 2006, 4:39 pm
Location: Podunk Iowa
United States of America

Post by Greg D »

The 352 is an often propagated and very wrong rumor - ALL FE powered Slicks had 390s.
On the same note - ALL Y block powered Slicks had 312s too.
1964 F 100 - I am going to do "something" with it.......

viewtopic.php?f=32&t=15942

1987 Mustang LX Convertible, 2.3 Auto - cruiser.
1994 F 150 XLT 2WD


~ Yes - I adopted another cat..............

Cam L Milan,
You'll be missed my friend.
User avatar
ezernut9mm
Posts: 9141
Joined: July 21, 2006, 9:37 pm
Location: KCMO
Sweden

Post by ezernut9mm »

Greg D wrote:The 352 is an often propagated and very wrong rumor - ALL FE powered Slicks had 390s.
On the same note - ALL Y block powered Slicks had 312s too.
exactly.
always
"i believe i've achieved satisfaction".-bubbles
"should i be gettin" baked for this boys?"-bubbles


i could no longer keep "r.i.p.ing" all of our fallen brothers and sisters, so i say here, slick loads of love and much respect to all you beautiful people.
User avatar
lane
Posts: 19
Joined: November 22, 2009, 9:59 pm
Location: Pasadena, CA
Contact:
United States of America

Post by lane »

Thank you for your replies. I have another question for you. I'll be rebuilding the 390 that is in the truck currently. I teach at a local technical college that has an automotive program and they will be using it for one of the student projects (but not until next Fall). I have a newly rebuilt 351M that I have in my parts truck (66 F100). Can anyone tell be me if I can bolt up the 351M to the original manual 4 speed tranny in the 65? I can pull the mounts, etc. to mount the motor, but I'd like to use the 351m until I get the other done (for about a year). Is it just a matter of finding the right bell housing and if so, what am I asking for when I look?

I'm hoping these questions aren't too dumb. I've done some restores, but mostly bodywork.

Lane
A happy life is a simple life.
User avatar
lane
Posts: 19
Joined: November 22, 2009, 9:59 pm
Location: Pasadena, CA
Contact:
United States of America

Post by lane »

Sorry, one more question? What does "FE powered" mean?

Lane
A happy life is a simple life.
blackagatha
Posts: 2582
Joined: March 10, 2007, 12:49 am
Location: Arizona

Post by blackagatha »

LOL, good luck trying to use the 351 as a temp...... The 390 is an entirely different beast.

Different motor mounts, different transmission bolt pattern to almost anything else ever made. I guess you might find the right bell, good luck....

FE is the motor designation.... Ford-Edsel. 332 I think, 352, 360, 390, 410, 427, 428 are all FE's.
'63 with 390 & lots of juice. But never enough. Always want more.
ImageImageImage
User avatar
lane
Posts: 19
Joined: November 22, 2009, 9:59 pm
Location: Pasadena, CA
Contact:
United States of America

Post by lane »

Oh, I totally agree on keeping with the 390. I was just trying to buy some time. I've actually got some great punch out of my 351M, more than I thought, but it took some special doing (electric fans, shaved heads, some help from Edelbrock from the motor up, etc.) I'm excited to see what this 390 will do. Everyone's telling me it's a powerhouse in comparison. Thanks for your help. Nice truck - dig the flat black.
A happy life is a simple life.
User avatar
ezernut9mm
Posts: 9141
Joined: July 21, 2006, 9:37 pm
Location: KCMO
Sweden

Post by ezernut9mm »

i think the 351m uses the windsor bell housing and engine stands, so you'd have to change those.
always
"i believe i've achieved satisfaction".-bubbles
"should i be gettin" baked for this boys?"-bubbles


i could no longer keep "r.i.p.ing" all of our fallen brothers and sisters, so i say here, slick loads of love and much respect to all you beautiful people.
BarnieTrk
Posts: 1448
Joined: July 11, 2007, 2:37 pm
Location: Stanton, Michigan

Post by BarnieTrk »

ezernut9mm wrote:i think the 351m uses the windsor bell housing and engine stands, so you'd have to change those.
Ezernut,
If you are referring to the 351W engine as the Windsor, then nope, I believe the 351M/400 uses the same bellhousing as the 460 engines, not the 351W engine.

There were many late 70's trucks & Broncos equipped with the 351M/400 engines and a manual transmission as well as the 460s in the '70s & early '80s - mainly in F250s/F350s.
However, around my area, I'd have to search high & low to locate one. I would guesstimate that the majority of these trucks were equipped with the C6 automatic transmissions.

I have no guesses on interchangeability regarding which engine stands/mounts to use with the 351M into a '66 F100.


Lane,
I wouldn't be to quick to start locating 390 parts....
I suggest you pull a sparkplug and do a cylinder stroke measurement to confirm it is a 390 -- and not a 352 or 360 engine.
Although many parts do interchange, I'd still want to KNOW what size engine I'm truly building first.

IMHO, if I had a 351M rebuilt and just sitting idle in a parts truck, if I could make the swap without too many issues with clutch linkage, bellhousing, motor mounts, etc., I'd seriously consider putting it in your new-to-you '66 and leaving it in there. Sell off the parts or junk out whatever you can from the tired FE engine that came with the '66 truck and never look back!

Good Luck!
BarnieTrk
User avatar
ezernut9mm
Posts: 9141
Joined: July 21, 2006, 9:37 pm
Location: KCMO
Sweden

Post by ezernut9mm »

ok. thanks for the correction.
always
"i believe i've achieved satisfaction".-bubbles
"should i be gettin" baked for this boys?"-bubbles


i could no longer keep "r.i.p.ing" all of our fallen brothers and sisters, so i say here, slick loads of love and much respect to all you beautiful people.
36truck
Posts: 3152
Joined: October 20, 2007, 8:32 pm
Location: Land of Sunshine AZ
United States of America

Post by 36truck »

Yes 351M/400's use the 429/460 Bellhousing bolt pattern. They do however use the 302 Frame mounts. If you can find a 77-79 F150/250/350 2 wheel drive with a 302-351M/400 they will bolt onto your cross member.

This will help you out as to what is what on the perches

http://www.fordification.com/tech/engine-perches.htm.
Tom Williams
ronk16
Posts: 58
Joined: September 13, 2009, 7:16 pm

Post by ronk16 »

dont be afraid to use the 351m. i just finished my 351m with 70 4v heads, price motorsports adapters 4v wieand tunnelram a pair of 1850 holleys, pertronix ignitor 111 module lunati voodoo cam, lifters and push rods, dynos at 685 hp at 7000 rpm and 567 ft lbs at 5600, it sounds like it would be expensive but the biggest price was the heads at 500 bones, all other parts were used execpt for cam and valvetrain. all for about 2000 grand and some patients to look for the parts. good luck on the build
blackagatha
Posts: 2582
Joined: March 10, 2007, 12:49 am
Location: Arizona

Post by blackagatha »

ronk16 wrote:dont be afraid to use the 351m. i just finished my 351m with 70 4v heads, price motorsports adapters 4v wieand tunnelram a pair of 1850 holleys, pertronix ignitor 111 module lunati voodoo cam, lifters and push rods, dynos at 685 hp at 7000 rpm and 567 ft lbs at 5600, it sounds like it would be expensive but the biggest price was the heads at 500 bones, all other parts were used execpt for cam and valvetrain. all for about 2000 grand and some patients to look for the parts. good luck on the build

685 HP for 2 grand?????? wow, I need to start taking lessons from you.....
'63 with 390 & lots of juice. But never enough. Always want more.
ImageImageImage
Post Reply