I cut some rust out of the face of my cowling and found this behind it.
How do I fix this?
My first impulse was to slather it with JB Weld but I'm not sure if that would hold up very long.
Welding a patch in that tight a space is beyond my meager welding ability.
Any ideas?
Looks to me like you're going to have more cutting to do. Open up the top with a clean, square cut like you just did so that you can access the rot on the inside. Cut that out, replace it and then weld the top back on, then the front.
Bad news is it'll be a bit of work but not too bad. Good news is you can definitely treat the whole inner cowl while you have it opened up.
"If you don't want to stand behind our Troops, feel free to stand in front of them."
I agree with Max that welding is the right way to go as a first choice.
Max, what do you think about brazing the holes shut. I've been using that technique on pinholes on a bunch of Ford air cleaners I'm doing for a friend. It works great for pin holes since it doesn't melt the thin good metal away, like my MIG welder will (even at it's lowest setting), but those holes look a little too big.
If not fixed right that will let water into the cab and start more rust.
Agree cut the top clean, weld in a repair piece and then weld your way out coating everything too.
My take is rust = cancer. It has to be removed or it will come back and haunt you another day. In an area like this, just go through the trouble once and be done with it. Even if you can braze it, it's still a lot of work and would just hate to have everything finished and painted and a year later see bubbles inside that cowl.
Tim, the brazing that you're doing on the air cleaners sounds perfect though!
"If you don't want to stand behind our Troops, feel free to stand in front of them."
I would feel better knowing it was done right.
I'm a little nervous about cutting the top of the cowl though. Not sure how good it will look after I glob it back together.
should I cut the yellow line or the red?
Which is easier to weld back together?
I'd definitely try and avoid cutting the red. I think you'll have enough room to work within the yellow cut-out. IF you did have to cut out the top vents, I'd almost consider doing the whole thing or find a way to limit any distortion when you put it back.
"If you don't want to stand behind our Troops, feel free to stand in front of them."
Oh, and don't cut an inner corner, cut the top outer corner right above your yellow line. Much easier to weld and dress afterwards (ie. grind smooth). If you cut the inner corner where the yellow line is, your weld will have to sit in that groove and unless you're a top notch tig welder, difficult to make look purdy afterwards!!
"If you don't want to stand behind our Troops, feel free to stand in front of them."
Maybe blast or grind off as much rust as you can then cut a nice patch from 12 gage and glue it in place with body adhesive. No distortion and no leaks. Seam seal it all up and you are good to go.
It appears to be an etching primer with "other ingredients" added. I bought 3 cans, but only needed 1. I sprayed, while pulling the tube out. Heavy coats, instructions recomend that the stuff should drip out drainage holes to insure good coverage. Before I forget, I masked off the top of the cowl, to not get overspray all over everything. I got two coats out of one can. I hope I got it well applied, has to be better than what was there before.
Good luck with your repairs.
Driver: 71 F100 Shortbed: Disc swap, 5.0 HO EFI & AOD
Project Vehicle/Mild Custom: 66 F100 CC longbed: Sold
rctcomp wrote:I cut some rust out of the face of my cowling and found this behind it.
How do I fix this?
My first impulse was to slather it with JB Weld but I'm not sure if that would hold up very long.
Welding a patch in that tight a space is beyond my meager welding ability.
Any ideas?
It appears to be an etching primer with "other ingredients" added. I bought 3 cans, but only needed 1. I sprayed, while pulling the tube out. Heavy coats, instructions recomend that the stuff should drip out drainage holes to insure good coverage. Before I forget, I masked off the top of the cowl, to not get overspray all over everything. I got two coats out of one can. I hope I got it well applied, has to be better than what was there before.
Good luck with your repairs.
Good idea, 20 bucks sounds like cheap insurance. Thanks.