engine carnage with pics update 3-24

The place to talk Slicks. All we ask is that discussion has something to do with slicks...

Moderators: Casey 65, Kid

Post Reply
ICEMAN6166
Posts: 11470
Joined: July 11, 2006, 11:28 am
Location: Dove Creek, Co. elevation 6842
Poland

engine carnage with pics update 3-24

Post by ICEMAN6166 »

bad juju

so got into cleaning the cylinders out from the head gasket blow cleaned 6 of them out and the tops of the pistons off then when #6 was down in the hole i see this fine thing, appears that coolant was in the hole for the whole winter and eroded the cylinder wall.
pretty sure the decriptive word is (censored)

Image

Image

hey, cylinder bores are supposed to be smooth as a babys butt, this one is more like a teenagers acne pocked face.

not sure if it can be honed out, pistons are stamped .040 meaning engine has been bored.i checked it is indeed 3.790
i special ordered a full gasket set, so im already out that $
only choice at this point is to try to clean it up best as possible and put it back together and it will run because it was running the other day until the rings start to get eaten and it begins to burn oil and loose compression.
probably be ok for local use for a while but definitely not a long trip of thousands of miles

going to need to replace it im sure
not much for y blocks on cl around here

all for a $5 thermostat
AAARGH!
Last edited by ICEMAN6166 on March 24, 2016, 8:50 am, edited 1 time in total.
1966 F250 4x4
1964 Rambler Ambassador 990
Rest in peace departed Slick family members
Cam Milam
Lesley Ferguson
Steve Lopes
John Sutton
tomrooster
Posts: 613
Joined: July 28, 2006, 8:31 pm
Location: Monroe NJ
United States of America

Re: engine carnage with pics

Post by tomrooster »

Brian, I don't think it's all that bad, not good but you will probably never know the difference. It would be nice if it didn't happen but you should have years of service left. My 2cents. Tom
1966 F250 Camper Special parts truck
1966 F 100 w/391 ft
1965 F 100 project
1958 Edsel Pacer Convertible
1953 ford Customline 2 door
1952 8N
1967 triumph Bonneville

I'm still not a good welder but I've become a good grinder
User avatar
Toyz
Posts: 4334
Joined: March 22, 2011, 6:23 pm
Location: Baja Houston Taxes
United States of America

Re: engine carnage with pics

Post by Toyz »

Keep in mind that two stroke pistons often run across interrupted surfaces. Might rig a flex hone to favor the damaged area. Hone the heck out of it; maybe increase the oil viscosity, and Chive On! If it don't make Slickstock, we'll get you up to the Divide; it's all downhill from there!
Paul
The Ford Orphanage
Life's too short for boring vehicles!
My quest to develop a universal solvent is held up by the lack of a storage container.
Paul
BarnieTrk
Posts: 1448
Joined: July 11, 2007, 2:37 pm
Location: Stanton, Michigan

Re: engine carnage with pics

Post by BarnieTrk »

ICEMAN6166 wrote:bad juju

so got into cleaning the cylinders out from the head gasket blow cleaned 6 of them out and the tops of the pistons off then when #6 was down in the hole i see this fine thing, appears that coolant was in the hole for the whole winter and eroded the cylinder wall.
pretty sure the decriptive word is (censored)

hey, cylinder bores are supposed to be smooth as a babys butt, this one is more like a teenagers acne pocked face.

not sure if it can be honed out, pistons are stamped .040 meaning engine has been bored.i checked it is indeed 3.790
i special ordered a full gasket set, so im already out that $
only choice at this point is to try to clean it up best as possible and put it back together and it will run because it was running the other day until the rings start to get eaten and it begins to burn oil and loose compression.
probably be ok for local use for a while but definitely not a long trip of thousands of miles

going to need to replace it im sure
not much for y blocks on cl around here

all for a $5 thermostat
AAARGH!
Bummer on the cylinder wall corrosion, ICEMAN.

But I'm with TomRooster, I'm betting it'll hone/clean out without too much effort. Considering you're not racing it or pounding on it while bogging it through some mud hole, that you'll drive it sensibly, let it warm up, use good motor oil & change it & its filter adequately, I'd bet with a new set of file-to-fit rings - it'll serve you just fine.

Once rebuilt and given a 500 mile run-in, I would be interested to see what a compression test would reveal between cylinders....

BarnieTrk
slick4x4
Posts: 5725
Joined: April 19, 2008, 10:01 pm
Location: kipp kansas
United States of America

Re: engine carnage with pics

Post by slick4x4 »

I agree with the others
Hone it & run it
I bet you wouldn't notice anything (like smoke)
For a long time

If you get to Salina and its on its last leg
I know a guy that has some spare engines & a shop :D
.
.
.
'' I think what scares me the most about you guys is that I understand you '' ..... KID
'' lookin good, a little paint adds at least 100hp!'' ....... COOTER
'' well an old guy can dream cant he? ''............ICEMAN
''I would donate organs before selling my slick''........ HOOFBEAT RACER
ICEMAN6166
Posts: 11470
Joined: July 11, 2006, 11:28 am
Location: Dove Creek, Co. elevation 6842
Poland

Re: engine carnage with pics

Post by ICEMAN6166 »

well heres an update
took the wifes phone with the pics when i went to pick up parts
the owner of the store does a lot of engine rebuilding and we had a long discussion on the matter
heres the gist
we agreed that its pretty impossible for that to have happened over the winter especially considering i had new coolant and the value being near -65F (i have a tester and test before every winter)
he thought i could hone but not likely to improve it much and since there are no sharp edges and it does not stick and ran fine before the only issue i might have is a slight puff of oil when the piston went past that spot. since i never had to add more than 1 quart between changes and run 15w40 in it its probably going to be ok for quite a while
add to that the rings going past it are as he said going to do more than i could honing
also mentioned that if i removed the piston i might have to get rings if something happened and they come in sets of 8 so what an unneeded expense i could incur and what do you do with 7 sets of +.040 rings
anyways both heads and rockers are back on already
going to finish it up tomorrow and do a compression test both before i fire it up and after its ran awhile to see where its at

on a side note and this is the fault of the checker in quality control at fel-pro, the kit was short the oilpan gasket :cussing:
i have one so its not going to hurt my assembly and im pretty sure the parts store and or EPW will make it right either by discount or an oilpan set and then EPW can try to soak felpro.
1966 F250 4x4
1964 Rambler Ambassador 990
Rest in peace departed Slick family members
Cam Milam
Lesley Ferguson
Steve Lopes
John Sutton
User avatar
bird55
Posts: 558
Joined: February 16, 2009, 11:56 am
Location: Tulsa, Oklahoma
United States of America

Re: engine carnage with pics

Post by bird55 »

Ice, the good news is ,it is a yblock and will survive. It may smoke but it will keep on going!. I have one that has VERY worn cylinders and guides. Uses oil and smokes out the neighborhood for mosquitoes!. But it still gets a lot of work done. I have another used engine standing by that has very low miles 40,000 / 1964, f100. Looks like a new one inside. Next time let me know I bet with some patience we could have scrounged up the need rings for one cylinder.
User avatar
Toyz
Posts: 4334
Joined: March 22, 2011, 6:23 pm
Location: Baja Houston Taxes
United States of America

Re: engine carnage with pics

Post by Toyz »

Brian, not trying to be pessimistic, but I would still certainly perform a cooling system pressure test after re-assembly.
Paul
The Ford Orphanage
Life's too short for boring vehicles!
My quest to develop a universal solvent is held up by the lack of a storage container.
Paul
BarnieTrk
Posts: 1448
Joined: July 11, 2007, 2:37 pm
Location: Stanton, Michigan

Re: engine carnage with pics

Post by BarnieTrk »

ICEMAN6166 wrote:...also mentioned that if i removed the piston i might have to get rings if something happened and they come in sets of 8 so what an unneeded expense i could incur and what do you do with 7 sets of +.040 rings...
I realize that only the 292 Y-block had a 3.75" bore; but i am having a hard time believing that a single piston set of 0.040" file-to-fit rings cannot be purchased from someone/somewhere.

But since you've got it back together already, it is a moot point now.......

I hope you report back as to what results you get from the compression test......

Ryan
ICEMAN6166
Posts: 11470
Joined: July 11, 2006, 11:28 am
Location: Dove Creek, Co. elevation 6842
Poland

Re: engine carnage with pics

Post by ICEMAN6166 »

almost to the point of the compression test, will get there today
i do not have a pressure tester for the cooling system and there are no tool rentals nearby
1966 F250 4x4
1964 Rambler Ambassador 990
Rest in peace departed Slick family members
Cam Milam
Lesley Ferguson
Steve Lopes
John Sutton
ICEMAN6166
Posts: 11470
Joined: July 11, 2006, 11:28 am
Location: Dove Creek, Co. elevation 6842
Poland

Re: engine carnage with pics update 3-24

Post by ICEMAN6166 »

so far so good
got everything back together and fired it up last night
ran it for an hour at varying idle speeds with no unusual noise, overheating , or leaks and no milky oil afterwards
hope this ends this issue
still not quite ready for a road test as not all of the lights are hooked up and therfes tape and paper covering the windows for painting
hoping i can get in some road time this weekend
1966 F250 4x4
1964 Rambler Ambassador 990
Rest in peace departed Slick family members
Cam Milam
Lesley Ferguson
Steve Lopes
John Sutton
BarnieTrk
Posts: 1448
Joined: July 11, 2007, 2:37 pm
Location: Stanton, Michigan

Re: engine carnage with pics update 3-24

Post by BarnieTrk »

You're making EXCELLENT progress, ICEMAN! :cheers:
Keep us updated please! :thumright:
BarnieTrk :steering:
User avatar
skidoorulz
Posts: 359
Joined: April 11, 2013, 9:02 pm
Location: Billings MT
United States of America

Re: engine carnage with pics update 3-24

Post by skidoorulz »

There is a reason they are known as fail pro gaskets. I made the mistake of using them on my rebuild with the same results. Head gaskets leaking. Had to replace them within 600 miles. I used a set of Best gaskets and no problems. Don't give up on that engine Y's can be bored 90 over.
ICEMAN6166
Posts: 11470
Joined: July 11, 2006, 11:28 am
Location: Dove Creek, Co. elevation 6842
Poland

Re: engine carnage with pics update 3-24

Post by ICEMAN6166 »

skidoorulz wrote:There is a reason they are known as fail pro gaskets. I made the mistake of using them on my rebuild with the same results. Head gaskets leaking. Had to replace them within 600 miles. I used a set of Best gaskets and no problems. Don't give up on that engine Y's can be bored 90 over.
not sure what brand the blown gaskets were.
never had any fel-pro issues before and used them for lots of years
as to the +.090, i had an 390 fe bored out that much with a 428 crank and it was a screamin demon LOL
1966 F250 4x4
1964 Rambler Ambassador 990
Rest in peace departed Slick family members
Cam Milam
Lesley Ferguson
Steve Lopes
John Sutton
BarnieTrk
Posts: 1448
Joined: July 11, 2007, 2:37 pm
Location: Stanton, Michigan

Re: engine carnage with pics update 3-24

Post by BarnieTrk »

I wouldn't be so sure that ALL 292 or 390 blocks could go 0.090" overbore safety. The issue is core shift during production + thin wall casting = high risk for overheating if going more than 0.040" overbore.

ICEMAN, I realize you likely are not planning on trying to "race" your 292 or add some form of power adder (nitrous oxide injection, supercharger, turbo, etc.) but with something as simple and out of your control as todays' CRAP gasoline - which can be the cause for pre-detonation, (which can be like a grenade to thin cyl walls, too flexible to support the RPM &/or HP) you could crack a thin cylinder wall.

One option for folks who still want to go with the overbore is that they can opt for putting a block filler in it to help support iffy cylinder walls. For maybe more piece of mind, a fella may rather have the block cylinder walls sonic-checked on all 4 sides' (front, back, left, right) of each cylinder to determine the actual cylinder wall thicknesses before pulling the trigger on going with larger overbores. Just my :2cents:

BarnieTrk

P.S.
Regarding gaskets: I've had good luck with Fel-Pro gaskets (parent company is Federal Mogul Corp.) but if I have a choice, I prefer to opt for Victor-Reinz gaskets (parent company is DANA Holding Corp.)
Secondly, I know many do not advocate rechecking the torque of head gaskets after the first heat cycle, but I still do and recommend it. It can't hurt and it may help from having problems down the line.
ICEMAN6166
Posts: 11470
Joined: July 11, 2006, 11:28 am
Location: Dove Creek, Co. elevation 6842
Poland

Re: engine carnage with pics update 3-24

Post by ICEMAN6166 »

BarnieTrk wrote:ICEMAN, I realize you likely are not planning on trying to "race" your 292 or add some form of power adder (nitrous oxide injection, supercharger, turbo, etc.) but with something as simple and out of your control as todays' CRAP gasoline - which can be the cause for pre-detonation, (which can be like a grenade to thin cyl walls, too flexible to support the RPM &/or HP) you could crack a thin cylinder wall.
yes not a race truck, but it does carry heavy loads from time to time
still rarely if ever does it get to or pass 4k rpm
as for crap gas i have always used the lucas additive or non-ethanol gas since i have been down here (all gas in Alaska was ethanol free)
1966 F250 4x4
1964 Rambler Ambassador 990
Rest in peace departed Slick family members
Cam Milam
Lesley Ferguson
Steve Lopes
John Sutton
Post Reply