Door Seal help

The place to talk Slicks. All we ask is that discussion has something to do with slicks...

Moderators: Casey 65, Kid

Post Reply
Leeroy
Posts: 1115
Joined: July 12, 2009, 3:52 am
Location: Melbourne, Australia
Australia

Door Seal help

Post by Leeroy »

Hi all, been pretty busy the last few months so missing some of the action around her lately.... Thought I'd ask a question about door seals.

I bought a complete cab kit from Tom a few years back and fitted it all, really happy with the quality and fit of everything but I am having some trouble with the door seals. I'm wondering if I installed them incorrectly or if I'm missing something.

The door fits well, top around the vent windows is all perfect, small gap at the bottom rear corner.
But inside I am getting a small gap where the vent window edge of the door contacts the cab. Its the same on both driver and passenger sides.
It wouldn't really bother me very much but Ive been driving the slick a lot the last few months and it REALLY catches the wind noise around the gap. If I pull the door HARD whilst driving the seal closes up a bit more and the wind noise reduces dramatically.

The pic below is with the door completely closed.

Image


Image

Ive just cracked the door slightly here so you can see where the gap is right at the top where the sun is coming through.

Image
Image

This is how I've fitted the seal
Image
Image
User avatar
unibody madness
Posts: 2147
Joined: December 4, 2008, 4:33 pm
Location: Paradise,CALIFORNIA 95969
United States of America

Re: Door Seal help

Post by unibody madness »

I am guessing the door is twisted, if it fits right everywhere else roll down your window open your wing put a padded two x four between the truck cab and the opposite top of door and gently twisted the wing corner of the door towards the cab.
Turk build thread at:
http://slick60s.com/viewtopic.php?f=32&t=18944

It does not matter what you think, it only matters what you do about it!
tomrooster
Posts: 613
Joined: July 28, 2006, 8:31 pm
Location: Monroe NJ
United States of America

Re: Door Seal help

Post by tomrooster »

I have the same problem on the drivers door, not so much on the passenger side, rain comes in and wind noise , I also have new rubber seals. Tom
1966 F250 Camper Special parts truck
1966 F 100 w/391 ft
1965 F 100 project
1958 Edsel Pacer Convertible
1953 ford Customline 2 door
1952 8N
1967 triumph Bonneville

I'm still not a good welder but I've become a good grinder
64 f100
Posts: 2754
Joined: July 18, 2006, 7:23 am
Location: Carmi, Illinois, 62821

Re: Door Seal help

Post by 64 f100 »

There are several adjustments you can do to the door with the hinges. Sometimes these will work for you and sometimes you have to get creative. It looks to me as if you may have to bend the window frame some to make it fit. Basically the old use a piece of wood and apply force to the upper part which I believe someone else suggested.

Rich
Leeroy
Posts: 1115
Joined: July 12, 2009, 3:52 am
Location: Melbourne, Australia
Australia

Re: Door Seal help

Post by Leeroy »

Yes I thought that may be the case, but Im reluctant to bend the door as it fits very well into the cab frame. The window frame is perfect (for a 60's car) The only area I'd say that isn't is the bottom rear of the door where the curve is. Theres probably a 1/8 to MAYBE 1/4 that sits proud. So bending this part of the door I don't believe would assist the gap along the vent part?
Im thinking to seal that gap I'd need to bend the door frame in at least 1/8 maybe more to contact the seal. Which would then leave the door frame not flush with the pillar anymore. :cussing:
I wondered if there was something seal wise like a flat piece of rubber that would attach to the door frame of the cab to take up the gap?
bruceandersson
Posts: 906
Joined: August 12, 2009, 9:44 am
Location: Ohio

Re: Door Seal help

Post by bruceandersson »

I'd move the whole front of the door inwards to try and close the gap. My understanding of all ford doors int he 60s was that they were set a little inward from the fender/windshield in order to reduce wind noise. If you want to keep the alignment you have and don't want to bend the door, then you'll have to move the seal inward by placing something behind it. You could get a small piece of edpm roofing. Its about 1/16 thick so two layers would move the rubber out about 1/2 inch. You cold leave the w/s alone and just glue the same onto the body to bring its surface out.
Post Reply